修改部分参数

Co-authored-by: Copilot <copilot@github.com>

print_config/prusa_slicer/materials/CR-PETG.ini

@@ -6,6 +6,7 @@ filament_type = petg
 [settings]
 ; filament_adhesiveness_category = 300
 idle_temperature = 160
+bed_temperature = 70
 first_layer_bed_temperature = 70
 ;;;cool_plate_temp = 70
 ;;;eng_plate_temp = 0

print_config/prusa_slicer/materials/CR-PLA.ini

@@ -5,6 +5,7 @@ filament_type = pla
 
 [settings]
 idle_temperature = 150
+bed_temperature = 60
 first_layer_bed_temperature = 60
 ;;;cool_plate_temp = 50
 ;;;eng_plate_temp = 45

print_config/prusa_slicer/materials/Generic_PETG.ini

@@ -6,6 +6,7 @@ filament_type = petg
 [settings]
 ; filament_adhesiveness_category = 300
 idle_temperature = 160
+bed_temperature = 70
 first_layer_bed_temperature = 70
 ;;;cool_plate_temp = 60
 ;;;eng_plate_temp = 0

print_config/prusa_slicer/materials/Generic_TPU.ini

@@ -5,6 +5,7 @@ filament_type = tpu
 
 [settings]
 idle_temperature = 130
+bed_temperature = 55
 first_layer_bed_temperature = 55
 ;;;cool_plate_temp = 30
 ;;;eng_plate_temp = 30

print_config/prusa_slicer/materials/Hyper_L-W_PLA.ini

@@ -5,6 +5,7 @@ filament_type = pla
 
 [settings]
 idle_temperature = 150
+bed_temperature = 60
 first_layer_bed_temperature = 60
 ;;;cool_plate_temp = 50
 ;;;eng_plate_temp = 45

print_config/prusa_slicer/materials/Hyper_Marble_PLA.ini

@@ -5,6 +5,7 @@ filament_type = pla
 
 [settings]
 idle_temperature = 150
+bed_temperature = 60
 first_layer_bed_temperature = 60
 ;;;cool_plate_temp = 50
 ;;;eng_plate_temp = 45

print_config/prusa_slicer/materials/Hyper_PETG.ini

@@ -6,6 +6,8 @@ filament_type = petg
 [settings]
 ; filament_adhesiveness_category = 300
 idle_temperature = 160
+bed_temperature = 70
+first_layer_bed_temperature = 70
 ;;;cool_plate_temp = 60
 ;;;eng_plate_temp = 0
 ;;;hot_plate_temp = 70
@@ -49,8 +51,6 @@ max_fan_speed = 80
 min_fan_speed = 40
 ;;;slow_down_min_speed = 10
 slowdown_below_layer_time = 8
-bed_temperature = 70
-first_layer_bed_temperature = 70
 ;;;filament_start_gcode = ;filament start gcode\n
 temperature = 240
 ;;;temperature_vitrification = 80

print_config/prusa_slicer/materials/Hyper_PLA.ini

@@ -5,6 +5,7 @@ filament_type = pla
 
 [settings]
 idle_temperature = 150
+bed_temperature = 60
 first_layer_bed_temperature = 60
 ;;;cool_plate_temp = 50
 ;;;eng_plate_temp = 45

print_config/prusa_slicer/materials/Hyper_Stardust_PLA.ini

@@ -5,6 +5,7 @@ filament_type = pla
 
 [settings]
 idle_temperature = 150
+bed_temperature = 60
 first_layer_bed_temperature = 60
 ;;;cool_plate_temp = 50
 ;;;eng_plate_temp = 45

print_config/prusa_slicer/materials/Soleyin_Ultra_PLA.ini

@@ -5,6 +5,7 @@ filament_type = pla
 
 [settings]
 idle_temperature = 150
+bed_temperature = 60
 first_layer_bed_temperature = 60
 ;;;cool_plate_temp = 50
 ;;;eng_plate_temp = 45

print_config/prusa_slicer/printers/Ender3_V3_SE.ini

@@ -48,7 +48,7 @@ single_extruder_multi_material = 1
 start_filament_gcode = ;Do nothing
 wipe = 1
 before_layer_gcode = ;BEFORE_LAYER_CHANGE\n;[layer_z]\nG92 E0\n
-start_gcode = M220 S100 ;Reset Feedrate \nM221 S100 ;Reset Flowrate \n \nM140 S{first_layer_bed_temperature[0]} ;Set final bed temp \nG28 ;Home \n \nG92 E0 ;Reset Extruder \nG1 Z2.0 F3000 ;Move Z Axis up \nM104 S{first_layer_temperature[0]} ;Set final nozzle temp \nG1 X-10 Y20 Z3 F5000.0 ;Move to out position \nM190 S{first_layer_bed_temperature[0]} ;Wait for bed temp to stabilize \nM109 S{temperature[0]} ;Wait for nozzle temp to stabilize \nG1 X-2.1 Y20 Z0.28 F5000.0 ;Move to start position \n G1 X-2.1 Y145.0 Z0.28 F1500.0 E15 ;Draw the first line \nG1 X-2.4 Y145.0 Z0.28 F5000.0 ;Move to side a little \nG1 X-2.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line \nG92 E0  ;Reset Extruder \nG1 E-1.0000 F1800 ;Retract a bit \nG1 Z2.0 F3000 ;Move Z Axis up \nG1 E0.0000 F1800
+start_gcode = M220 S100 ;Reset Feedrate \nM221 S100 ;Reset Flowrate \n \nM140 S{first_layer_bed_temperature[0]} ;Set final bed temp \nG28 ;Home \n \nG92 E0 ;Reset Extruder \nG1 Z2.0 F3000 ;Move Z Axis up \nM104 S{first_layer_temperature[0]} ;Set final nozzle temp \nG1 X-13 Y20 Z3 F5000.0 ;Move to out position \nM190 S{first_layer_bed_temperature[0]} ;Wait for bed temp to stabilize \nM109 S{temperature[0]} ;Wait for nozzle temp to stabilize \nG1 X-2.1 Y20 Z0.28 F5000.0 ;Move to start position \n G1 X-2.1 Y145.0 Z0.28 F1500.0 E15 ;Draw the first line \nG1 X-2.4 Y145.0 Z0.28 F5000.0 ;Move to side a little \nG1 X-2.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line \nG92 E0  ;Reset Extruder \nG1 E-1.0000 F1800 ;Retract a bit \nG1 Z2.0 F3000 ;Move Z Axis up \nG1 E0.0000 F1800
 end_gcode = G91 ;Relative positionning \nG1 E-2 F2700 ;Retract a bit \nG1 E-2 Z0.2 F2400 ;Retract and raise Z \nG1 X5 Y5 F3000 ;Wipe out \nG1 Z10 ;Raise Z more \nG90 ;Absolute positionning \n \nG1 X0 Y220 ;Present print \nM106 S0 ;Turn-off fan \nM104 S0 ;Turn-off hotend \nM140 S0 ;Turn-off bed \n \nM84 X Y E ;Disable all steppers but Z
 machine_max_acceleration_travel = 2000,2000
 pause_print_gcode = M25