准备大修参数

Co-authored-by: Copilot <copilot@github.com>

print_config/prusa_slicer/materials/CR-PETG.ini

@@ -51,10 +51,7 @@ slow_down_layer_time = 8
 filament_start_gcode = ; filament start gcode\n
 nozzle_temperature = 230
 temperature_vitrification = 80
-activate_air_filtration = 0
-activate_chamber_temp_control = 0
 additional_cooling_fan_speed = 0
-chamber_temperature = 35
 complete_print_exhaust_fan_speed = 80
 cool_cds_fan_start_at_height = 0
 cool_special_cds_fan_speed = 0

print_config/prusa_slicer/printers/Ender3_V3_SE.ini

@@ -5,13 +5,11 @@ show_name = Ender3 V3 SE Model
 [settings]
 family = Creality
 printer_technology = FFF
-deretraction_speed = 30
+deretract_speed = 30
 extruder_colour = #FCE94F
 extruder_offset = 0x0
 gcode_flavor = marlin2
 silent_mode = 0
-support_chamber_temp_control = 0
-support_air_filtration = 0
 machine_max_acceleration_e = 5000,5000
 machine_max_acceleration_extruding = 5000,5000
 machine_max_acceleration_retracting = 2500,2500
@@ -30,34 +28,33 @@ machine_min_extruding_rate = 0,0
 machine_min_travel_rate = 0,0
 max_layer_height = 0.36
 min_layer_height = 0.08
-printable_height = 250
+max_print_height = 250
 extruder_clearance_radius = 90
 extruder_clearance_height_to_rod = 47
 extruder_clearance_height_to_lid = 34
 nozzle_diameter = 0.4
-printer_settings_id = 
 printer_variant = 0.4
-retraction_minimum_travel = 1
+retract_before_travel = 1
 retract_before_wipe = 100
-retract_when_changing_layer = 1
-retraction_length = 0.8
+retract_layer_change = 1
+retract_length = 0.8
 retract_length_toolchange = 1
 z_hop = 0.4
 retract_restart_extra = 0
 retract_restart_extra_toolchange = 0
-retraction_speed = 30
+retract_speed = 30
 single_extruder_multi_material = 1
 change_filament_gcode = 
 wipe = 1
 z_hop_types = Slope Lift
-before_layer_change_gcode = ;BEFORE_LAYER_CHANGE\n;[layer_z]\nG92 E0\n
+before_layer_gcode = ;BEFORE_LAYER_CHANGE\n;[layer_z]\nG92 E0\n
 default_print_profile = 0.20mm Standard @Creality Ender-3 V3 SE 0.4 nozzle
 machine_start_gcode = M220 S100 ;Reset Feedrate \nM221 S100 ;Reset Flowrate \n \nM140 S[bed_temperature_initial_layer_single] ;Set final bed temp \nG28 ;Home \n \nG92 E0 ;Reset Extruder \nG1 Z2.0 F3000 ;Move Z Axis up \nM104 S[nozzle_temperature_initial_layer] ;Set final nozzle temp \nG1 X-2.1 Y20 Z0.28 F5000.0 ;Move to start position \nM190 S[bed_temperature_initial_layer_single] ;Wait for bed temp to stabilize \nM109 S[nozzle_temperature_initial_layer] ;Wait for nozzle temp to stabilize \nG1 X-2.1 Y145.0 Z0.28 F1500.0 E15 ;Draw the first line \nG1 X-2.4 Y145.0 Z0.28 F5000.0 ;Move to side a little \nG1 X-2.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line \nG92 E0  ;Reset Extruder \nG1 E-1.0000 F1800 ;Retract a bit \nG1 Z2.0 F3000 ;Move Z Axis up \nG1 E0.0000 F1800
 machine_end_gcode = G91 ;Relative positionning \nG1 E-2 F2700 ;Retract a bit \nG1 E-2 Z0.2 F2400 ;Retract and raise Z \nG1 X5 Y5 F3000 ;Wipe out \nG1 Z10 ;Raise Z more \nG90 ;Absolute positionning \n \nG1 X0 Y220 ;Present print \nM106 S0 ;Turn-off fan \nM104 S0 ;Turn-off hotend \nM140 S0 ;Turn-off bed \n \nM84 X Y E ;Disable all steppers but Z
 machine_max_acceleration_travel = 5000,5000
 machine_pause_gcode = M25
 bed_exclude_area = 0x0
-layer_change_gcode = 
+layer_gcode = 
 scan_first_layer = 0
 nozzle_type = brass
 auxiliary_fan = 0

print_config/prusa_slicer/quality/0.08mm_Extra_Fine.ini

@@ -66,7 +66,7 @@ inner_wall_acceleration = 2000
 ironing_flow = 15%
 ironing_spacing = 0.1
 ironing_speed = 20
-ironing_type = no ironing
+ironing_type = top
 layer_height = 0.08
 overhang_1_4_speed = 0
 overhang_2_4_speed = 20

print_config/prusa_slicer/quality/0.12mm_Fine.ini

@@ -66,7 +66,7 @@ inner_wall_acceleration = 2000
 ironing_flow = 15%
 ironing_spacing = 0.1
 ironing_speed = 20
-ironing_type = no ironing
+ironing_type = top
 layer_height = 0.12
 overhang_1_4_speed = 0
 overhang_2_4_speed = 20

print_config/prusa_slicer/quality/0.16mm_Optimal.ini

@@ -66,7 +66,7 @@ inner_wall_acceleration = 2000
 ironing_flow = 15%
 ironing_spacing = 0.1
 ironing_speed = 20
-ironing_type = no ironing
+ironing_type = top
 layer_height = 0.16
 overhang_1_4_speed = 0
 overhang_2_4_speed = 20

print_config/prusa_slicer/quality/0.20mm_Standard.ini

@@ -66,7 +66,7 @@ inner_wall_acceleration = 2000
 ironing_flow = 15%
 ironing_spacing = 0.1
 ironing_speed = 20
-ironing_type = no ironing
+ironing_type = top
 layer_height = 0.2
 overhang_1_4_speed = 0
 overhang_2_4_speed = 60

print_config/prusa_slicer/supports/grid_support.ini

@@ -3,8 +3,8 @@ show_name = Grid Support
 
 
 [settings]
-enable_support = 1
-support_filament = 0
+support_material = 1
+
 support_line_width = 0.4
 support_interface_filament = 0
 support_on_build_plate_only = 0
@@ -20,7 +20,7 @@ support_threshold_angle = 30
 support_object_xy_distance = 0.35
 
 support_type = normal(auto)
-support_style = Grid
+support_material_style = Grid
 support_interface_bottom_layers = 2
 tree_support_branch_angle = 45
 tree_support_wall_count = 0

print_config/prusa_slicer/supports/no_support.ini

@@ -3,8 +3,8 @@ show_name = No Support
 
 
 [settings]
-enable_support = 0
-support_filament = 0
+support_material = 0
+
 support_line_width = 0.4
 support_interface_filament = 0
 support_on_build_plate_only = 0
@@ -20,7 +20,7 @@ support_threshold_angle = 30
 support_object_xy_distance = 0.35
 
 support_type = normal(auto)
-support_style = default
+support_material_style = default
 support_interface_bottom_layers = 2
 tree_support_branch_angle = 45
 tree_support_wall_count = 0

print_config/prusa_slicer/supports/snug_support.ini

@@ -4,7 +4,7 @@ show_name = Snug Support
 
 [settings]
 enable_support = 1
-support_filament = 0
+
 support_line_width = 0.4
 support_interface_filament = 0
 support_on_build_plate_only = 0

print_config/prusa_slicer/supports/tree_support.ini

@@ -4,7 +4,7 @@ show_name = Tree Support
 
 [settings]
 enable_support = 1
-support_filament = 0
+
 support_line_width = 0.4
 support_interface_filament = 0
 support_on_build_plate_only = 0