lhye200/AIO_3D_Print_Web_Platform
1
0
Fork 0
Code Issues Pull Requests Actions Packages Projects Releases Wiki Activity

tmp prusa配置文件集

Browse Source 
Co-authored-by: Copilot <copilot@github.com>
This commit is contained in:
lhye200
2026-04-24 00:47:32 +08:00
parent 0416922a94
commit 22a6493e24
31 changed files with 2255 additions and 168 deletions
Download Patch File Download Diff File Expand all files Collapse all files

94
print_config/prusa_slicer/materials/CR-PETG.ini Normal file
View File

@@ -0,0 +1,94 @@
[metadata]
show_name = CR-PETG
material_type = petg
[settings]
filament_adhesiveness_category = 300
cool_plate_temp = 70
eng_plate_temp = 0
hot_plate_temp = 70
textured_plate_temp = 70
cool_plate_temp_initial_layer = 70
eng_plate_temp_initial_layer = 0
hot_plate_temp_initial_layer = 70
textured_plate_temp_initial_layer = 70
overhang_fan_threshold = 25%
overhang_fan_speed = 90
slow_down_for_layer_cooling = 1
close_fan_the_first_x_layers = 3
filament_end_gcode = ; filament end gcode \n
filament_flow_ratio = 0.95
reduce_fan_stop_start_freq = 1
fan_cooling_layer_time = 30
filament_cost = 14
filament_density = 1.23
filament_deretraction_speed = nil
filament_diameter = 1.75
filament_max_volumetric_speed = 9
filament_minimal_purge_on_wipe_tower = 15
filament_retraction_minimum_travel = nil
filament_retract_before_wipe = nil
filament_retract_when_changing_layer = nil
filament_retraction_length = nil
filament_z_hop = nil
filament_z_hop_types = nil
filament_retract_restart_extra = 0
filament_retraction_speed = nil
filament_settings_id =
filament_soluble = 0
filament_type = PETG
filament_vendor = Creality
filament_wipe = nil
filament_wipe_distance = nil
bed_type = Cool Plate
nozzle_temperature_initial_layer = 230
full_fan_speed_layer = 0
fan_max_speed = 40
fan_min_speed = 30
slow_down_min_speed = 10
slow_down_layer_time = 8
filament_start_gcode = ; filament start gcode\n
nozzle_temperature = 230
temperature_vitrification = 80
activate_air_filtration = 0
activate_chamber_temp_control = 0
additional_cooling_fan_speed = 0
chamber_temperature = 35
complete_print_exhaust_fan_speed = 80
cool_cds_fan_start_at_height = 0
cool_special_cds_fan_speed = 0
default_filament_colour = ""
during_print_exhaust_fan_speed = 60
enable_overhang_bridge_fan = 1
enable_pressure_advance = 1
enable_special_area_additional_cooling_fan = 0
epoxy_resin_plate_temp = 70
epoxy_resin_plate_temp_initial_layer = 70
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_is_support = 0
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_multitool_ramming = 0
filament_multitool_ramming_flow = 10
filament_multitool_ramming_volume = 10
filament_notes = ""
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_lift_above = 0
filament_retract_lift_below = 0
filament_retract_lift_enforce = All Surfaces
filament_shrink = 100%
filament_toolchange_delay = 0
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
material_flow_dependent_temperature = 0
material_flow_temp_graph = [[3.0,210], [10.0,220], [12.0,230]]
nozzle_temperature_range_high = 270
nozzle_temperature_range_low = 220
pressure_advance = 0.08
required_nozzle_HRC = 0
support_material_interface_fan_speed = -1

94
print_config/prusa_slicer/materials/CR-PLA.ini Normal file
View File

@@ -0,0 +1,94 @@
[metadata]
show_name = CR-PLA
material_type = pla
[settings]
cool_plate_temp = 50
eng_plate_temp = 45
hot_plate_temp = 50
textured_plate_temp = 50
cool_plate_temp_initial_layer = 50
eng_plate_temp_initial_layer = 45
hot_plate_temp_initial_layer = 50
textured_plate_temp_initial_layer = 50
overhang_fan_threshold = 50%
overhang_fan_speed = 100
slow_down_for_layer_cooling = 1
close_fan_the_first_x_layers = 1
filament_end_gcode = ;filament end gcode
filament_flow_ratio = 0.95
reduce_fan_stop_start_freq = 1
fan_cooling_layer_time = 100
filament_cost = 25
filament_density = 1.25
filament_deretraction_speed = nil
filament_diameter = 1.75
filament_max_volumetric_speed = 12
filament_minimal_purge_on_wipe_tower = 15
filament_retraction_minimum_travel = nil
filament_retract_before_wipe = nil
filament_retract_when_changing_layer = nil
filament_retraction_length = 1
filament_z_hop = 0.2
filament_z_hop_types = Slope Lift
filament_retract_restart_extra = 0
filament_retraction_speed = 40
filament_settings_id =
filament_soluble = 0
filament_type = PLA
filament_vendor = Creality
filament_wipe = nil
filament_wipe_distance = nil
bed_type = Cool Plate
nozzle_temperature_initial_layer = 190
full_fan_speed_layer = 0
fan_max_speed = 100
fan_min_speed = 100
slow_down_min_speed = 20
slow_down_layer_time = 6
filament_start_gcode = ;filament start gcode
nozzle_temperature = 190
temperature_vitrification = 100
filament_adhesiveness_category = 100
nozzle_temperature_range_low = 190
nozzle_temperature_range_high = 240
additional_cooling_fan_speed = 0
activate_air_filtration = 0
activate_chamber_temp_control = 0
chamber_temperature = 0
complete_print_exhaust_fan_speed = 80
cool_cds_fan_start_at_height = 0
cool_special_cds_fan_speed = 0
default_filament_colour = ""
during_print_exhaust_fan_speed = 60
enable_overhang_bridge_fan = 1
enable_pressure_advance = 0
enable_special_area_additional_cooling_fan = 0
epoxy_resin_plate_temp = 0
epoxy_resin_plate_temp_initial_layer = 0
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_is_support = 0
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_multitool_ramming = 0
filament_multitool_ramming_flow = 10
filament_multitool_ramming_volume = 10
filament_notes = ""
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_lift_above = 0
filament_retract_lift_below = 0
filament_retract_lift_enforce = All Surfaces
filament_shrink = 100%
filament_toolchange_delay = 0
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
material_flow_dependent_temperature = 0
material_flow_temp_graph = [[2.0,185],[4.0,190],[7.0,200]]
pressure_advance = 0.02
required_nozzle_HRC = 0
support_material_interface_fan_speed = -1

94
print_config/prusa_slicer/materials/Generic_PETG.ini Normal file
View File

@@ -0,0 +1,94 @@
[metadata]
show_name = Generic PETG
material_type = petg
[settings]
filament_adhesiveness_category = 300
cool_plate_temp = 60
eng_plate_temp = 0
hot_plate_temp = 70
textured_plate_temp = 70
cool_plate_temp_initial_layer = 60
eng_plate_temp_initial_layer = 0
hot_plate_temp_initial_layer = 70
textured_plate_temp_initial_layer = 70
overhang_fan_threshold = 25%
overhang_fan_speed = 90
slow_down_for_layer_cooling = 1
close_fan_the_first_x_layers = 3
filament_end_gcode = ;filament end gcode \n
filament_flow_ratio = 0.95
reduce_fan_stop_start_freq = 1
fan_cooling_layer_time = 30
filament_cost = 30
filament_density = 1.27
filament_deretraction_speed = nil
filament_diameter = 1.75
filament_max_volumetric_speed = 10
filament_minimal_purge_on_wipe_tower = 15
filament_retraction_minimum_travel = nil
filament_retract_before_wipe = nil
filament_retract_when_changing_layer = nil
filament_retraction_length = 1.2
filament_z_hop = 0.2
filament_z_hop_types = nil
filament_retract_restart_extra = 0
filament_retraction_speed = nil
filament_settings_id =
filament_soluble = 0
filament_type = PETG
filament_vendor = Creality
filament_wipe = nil
filament_wipe_distance = nil
bed_type = Cool Plate
nozzle_temperature_initial_layer = 220
full_fan_speed_layer = 0
fan_max_speed = 80
fan_min_speed = 40
slow_down_min_speed = 10
slow_down_layer_time = 8
filament_start_gcode = ;filament start gcode\n
nozzle_temperature = 220
temperature_vitrification = 80
activate_air_filtration = 0
activate_chamber_temp_control = 0
additional_cooling_fan_speed = 0
chamber_temperature = 0
complete_print_exhaust_fan_speed = 80
cool_cds_fan_start_at_height = 0
cool_special_cds_fan_speed = 0
default_filament_colour = ""
during_print_exhaust_fan_speed = 60
enable_overhang_bridge_fan = 1
enable_pressure_advance = 0
enable_special_area_additional_cooling_fan = 0
epoxy_resin_plate_temp = 0
epoxy_resin_plate_temp_initial_layer = 0
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_is_support = 0
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_multitool_ramming = 0
filament_multitool_ramming_flow = 10
filament_multitool_ramming_volume = 10
filament_notes = ""
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_lift_above = 0
filament_retract_lift_below = 0
filament_retract_lift_enforce = All Surfaces
filament_shrink = 100%
filament_toolchange_delay = 0
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
material_flow_dependent_temperature = 0
material_flow_temp_graph = [[3.5,200],[7.0,240]]
nozzle_temperature_range_high = 270
nozzle_temperature_range_low = 220
pressure_advance = 0.02
required_nozzle_HRC = 0
support_material_interface_fan_speed = -1

94
print_config/prusa_slicer/materials/Generic_TPU.ini Normal file
View File

@@ -0,0 +1,94 @@
[metadata]
show_name = Generic TPU
material_type = tpu
[settings]
cool_plate_temp = 30
eng_plate_temp = 30
hot_plate_temp = 30
textured_plate_temp = 30
cool_plate_temp_initial_layer = 30
eng_plate_temp_initial_layer = 30
hot_plate_temp_initial_layer = 30
textured_plate_temp_initial_layer = 30
overhang_fan_threshold = 95%
overhang_fan_speed = 100
slow_down_for_layer_cooling = 1
close_fan_the_first_x_layers = 1
filament_end_gcode = ;filament end gcode \n
filament_flow_ratio = 1
reduce_fan_stop_start_freq = 1
fan_cooling_layer_time = 100
filament_cost = 20
filament_density = 1.24
filament_deretraction_speed = nil
filament_diameter = 1.75
filament_max_volumetric_speed = 3
filament_minimal_purge_on_wipe_tower = 15
filament_retraction_minimum_travel = nil
filament_retract_before_wipe = nil
filament_retract_when_changing_layer = nil
filament_retraction_length = 2
filament_z_hop = 0.2
filament_z_hop_types = nil
filament_retract_restart_extra = 0
filament_retraction_speed = nil
filament_settings_id =
filament_soluble = 0
filament_type = TPU
filament_vendor = Generic
filament_wipe = nil
filament_wipe_distance = nil
bed_type = Cool Plate
nozzle_temperature_initial_layer = 200
full_fan_speed_layer = 0
fan_max_speed = 100
fan_min_speed = 100
slow_down_min_speed = 10
slow_down_layer_time = 12
filament_start_gcode = ;filament start gcode\n
nozzle_temperature = 200
temperature_vitrification = 60
filament_adhesiveness_category = 600
additional_cooling_fan_speed = 0
nozzle_temperature_range_low = 200
nozzle_temperature_range_high = 250
activate_air_filtration = 0
activate_chamber_temp_control = 0
chamber_temperature = 0
complete_print_exhaust_fan_speed = 80
cool_cds_fan_start_at_height = 0
cool_special_cds_fan_speed = 0
default_filament_colour = ""
during_print_exhaust_fan_speed = 60
enable_overhang_bridge_fan = 1
enable_pressure_advance = 0
enable_special_area_additional_cooling_fan = 0
epoxy_resin_plate_temp = 0
epoxy_resin_plate_temp_initial_layer = 0
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_is_support = 0
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_multitool_ramming = 0
filament_multitool_ramming_flow = 10
filament_multitool_ramming_volume = 10
filament_notes = ""
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_lift_above = 0
filament_retract_lift_below = 0
filament_retract_lift_enforce = All Surfaces
filament_shrink = 100%
filament_toolchange_delay = 0
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
material_flow_dependent_temperature = 0
material_flow_temp_graph = [[3.5,200],[7.0,240]]
pressure_advance = 0.02
required_nozzle_HRC = 0
support_material_interface_fan_speed = -1

96
print_config/prusa_slicer/materials/Hyper_L-W_PLA.ini Normal file
View File

@@ -0,0 +1,96 @@
[metadata]
show_name = Hyper L-W PLA
material_type = pla
[settings]
cool_plate_temp = 50
eng_plate_temp = 45
hot_plate_temp = 60
textured_plate_temp = 60
cool_plate_temp_initial_layer = 50
eng_plate_temp_initial_layer = 45
hot_plate_temp_initial_layer = 60
textured_plate_temp_initial_layer = 60
overhang_fan_threshold = 50%
overhang_fan_speed = 100
slow_down_for_layer_cooling = 1
close_fan_the_first_x_layers = 1
filament_end_gcode = ;filament end gcode
filament_flow_ratio = 0.75
reduce_fan_stop_start_freq = 1
fan_cooling_layer_time = 100
filament_cost = 48.9
filament_density = 1.21
filament_deretraction_speed = 15
filament_diameter = 1.75
filament_max_volumetric_speed = 4
filament_minimal_purge_on_wipe_tower = 15
filament_retraction_minimum_travel = 3
filament_retract_before_wipe = nil
filament_retract_when_changing_layer = nil
filament_retraction_length = 0.6
filament_z_hop = nil
filament_z_hop_types = nil
filament_retract_restart_extra = nil
filament_retraction_speed = 15
filament_settings_id =
filament_soluble = 0
filament_type = PLA
filament_vendor = Creality
filament_wipe = nil
filament_wipe_distance = nil
bed_type = Cool Plate
nozzle_temperature_initial_layer = 220
full_fan_speed_layer = 0
fan_max_speed = 100
fan_min_speed = 60
slow_down_min_speed = 10
slow_down_layer_time = 10
filament_start_gcode = ;filament start gcode
nozzle_temperature = 220
temperature_vitrification = 60
filament_adhesiveness_category = 100
nozzle_temperature_range_low = 200
nozzle_temperature_range_high = 270
additional_cooling_fan_speed = 0
activate_air_filtration = 0
activate_chamber_temp_control = 0
chamber_temperature = 0
complete_print_exhaust_fan_speed = 80
cool_cds_fan_start_at_height = 0.5
cool_special_cds_fan_speed = 0
customized_plate_temp = 60
customized_plate_temp_initial_layer = 60
default_filament_colour = ""
during_print_exhaust_fan_speed = 60
enable_overhang_bridge_fan = 1
enable_pressure_advance = 1
enable_special_area_additional_cooling_fan = 0
epoxy_resin_plate_temp = 60
epoxy_resin_plate_temp_initial_layer = 60
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_is_support = 0
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_multitool_ramming = 0
filament_multitool_ramming_flow = 10
filament_multitool_ramming_volume = 10
filament_notes = ""
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_lift_enforce = nil
filament_shrink = 100%
filament_shrinkage_compensation_z = 100%
filament_toolchange_delay = 0
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
material_flow_dependent_temperature = 0
pressure_advance = 0.1
required_nozzle_HRC = 0
support_material_interface_fan_speed = -1

97
print_config/prusa_slicer/materials/Hyper_Marble_PLA.ini Normal file
View File

@@ -0,0 +1,97 @@
[metadata]
show_name = Hyper Marble PLA
material_type = pla
[settings]
cool_plate_temp = 50
eng_plate_temp = 45
hot_plate_temp = 50
textured_plate_temp = 50
cool_plate_temp_initial_layer = 50
eng_plate_temp_initial_layer = 45
hot_plate_temp_initial_layer = 50
textured_plate_temp_initial_layer = 50
overhang_fan_threshold = 50%
overhang_fan_speed = 100
slow_down_for_layer_cooling = 1
close_fan_the_first_x_layers = 1
filament_end_gcode = ;filament end gcode
filament_flow_ratio = 0.95
reduce_fan_stop_start_freq = 1
fan_cooling_layer_time = 100
filament_cost = 23.9
filament_density = 1.25
filament_deretraction_speed = 15
filament_diameter = 1.75
filament_max_volumetric_speed = 18
filament_minimal_purge_on_wipe_tower = 15
filament_retraction_minimum_travel = 2
filament_retract_before_wipe = nil
filament_retract_when_changing_layer = nil
filament_retraction_length = 1.5
filament_z_hop = nil
filament_z_hop_types = nil
filament_retract_restart_extra = nil
filament_retraction_speed = 15
filament_settings_id =
filament_soluble = 0
filament_type = PLA
filament_vendor = Creality
filament_wipe = nil
filament_wipe_distance = 3
bed_type = Cool Plate
nozzle_temperature_initial_layer = 220
full_fan_speed_layer = 0
fan_max_speed = 100
fan_min_speed = 100
slow_down_min_speed = 20
slow_down_layer_time = 14
filament_start_gcode = ;filament start gcode
nozzle_temperature = 220
temperature_vitrification = 60
filament_adhesiveness_category = 100
nozzle_temperature_range_low = 190
nozzle_temperature_range_high = 240
additional_cooling_fan_speed = 0
activate_air_filtration = 0
activate_chamber_temp_control = 0
chamber_temperature = 0
complete_print_exhaust_fan_speed = 80
cool_cds_fan_start_at_height = 0
cool_special_cds_fan_speed = 0
customized_plate_temp = 50
customized_plate_temp_initial_layer = 50
default_filament_colour = ""
during_print_exhaust_fan_speed = 60
enable_overhang_bridge_fan = 1
enable_pressure_advance = 1
enable_special_area_additional_cooling_fan = 0
epoxy_resin_plate_temp = 50
epoxy_resin_plate_temp_initial_layer = 50
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_is_support = 0
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_multitool_ramming = 0
filament_multitool_ramming_flow = 10
filament_multitool_ramming_volume = 10
filament_notes = ""
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_lift_enforce = nil
filament_shrink = 100%
filament_shrinkage_compensation_z = 100%
filament_toolchange_delay = 0
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
material_flow_dependent_temperature = 0
material_flow_temp_graph = [[0.8,200],[1.0,200],[1.2,220]]
pressure_advance = 0.04
required_nozzle_HRC = 0
support_material_interface_fan_speed = -1

94
print_config/prusa_slicer/materials/Hyper_PETG.ini Normal file
View File

@@ -0,0 +1,94 @@
[metadata]
show_name = Hyper PETG
material_type = petg
[settings]
filament_adhesiveness_category = 300
cool_plate_temp = 60
eng_plate_temp = 0
hot_plate_temp = 70
textured_plate_temp = 70
cool_plate_temp_initial_layer = 60
eng_plate_temp_initial_layer = 0
hot_plate_temp_initial_layer = 70
textured_plate_temp_initial_layer = 70
overhang_fan_threshold = 25%
overhang_fan_speed = 90
slow_down_for_layer_cooling = 1
close_fan_the_first_x_layers = 3
filament_end_gcode = ;filament end gcode \n
filament_flow_ratio = 1.0
reduce_fan_stop_start_freq = 1
fan_cooling_layer_time = 30
filament_cost = 69
filament_density = 1.27
filament_deretraction_speed = nil
filament_diameter = 1.75
filament_max_volumetric_speed = 10
filament_minimal_purge_on_wipe_tower = 15
filament_retraction_minimum_travel = nil
filament_retract_before_wipe = nil
filament_retract_when_changing_layer = nil
filament_retraction_length = 1.2
filament_z_hop = 0.2
filament_z_hop_types = nil
filament_retract_restart_extra = 0
filament_retraction_speed = nil
filament_settings_id =
filament_soluble = 0
filament_type = PETG
filament_vendor = Creality
filament_wipe = nil
filament_wipe_distance = 2
bed_type = Cool Plate
nozzle_temperature_initial_layer = 235
full_fan_speed_layer = 0
fan_max_speed = 80
fan_min_speed = 40
slow_down_min_speed = 10
slow_down_layer_time = 8
filament_start_gcode = ;filament start gcode\n
nozzle_temperature = 240
temperature_vitrification = 80
activate_air_filtration = 0
activate_chamber_temp_control = 0
additional_cooling_fan_speed = 0
chamber_temperature = 0
complete_print_exhaust_fan_speed = 80
cool_cds_fan_start_at_height = 0
cool_special_cds_fan_speed = 0
default_filament_colour = ""
during_print_exhaust_fan_speed = 60
enable_overhang_bridge_fan = 1
enable_pressure_advance = 1
enable_special_area_additional_cooling_fan = 0
epoxy_resin_plate_temp = 0
epoxy_resin_plate_temp_initial_layer = 0
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_is_support = 0
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_multitool_ramming = 0
filament_multitool_ramming_flow = 10
filament_multitool_ramming_volume = 10
filament_notes = ""
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_lift_above = 0
filament_retract_lift_below = 0
filament_retract_lift_enforce = All Surfaces
filament_shrink = 100%
filament_toolchange_delay = 0
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
material_flow_dependent_temperature = 1
material_flow_temp_graph = [[3.0,230],[10.0,240],[20.0,250]]
nozzle_temperature_range_high = 270
nozzle_temperature_range_low = 220
pressure_advance = 0.07
required_nozzle_HRC = 0
support_material_interface_fan_speed = -1

94
print_config/prusa_slicer/materials/Hyper_PLA.ini Normal file
View File

@@ -0,0 +1,94 @@
[metadata]
show_name = Hyper PLA
material_type = pla
[settings]
cool_plate_temp = 50
eng_plate_temp = 45
hot_plate_temp = 50
textured_plate_temp = 50
cool_plate_temp_initial_layer = 50
eng_plate_temp_initial_layer = 45
hot_plate_temp_initial_layer = 50
textured_plate_temp_initial_layer = 50
overhang_fan_threshold = 50%
overhang_fan_speed = 100
slow_down_for_layer_cooling = 1
close_fan_the_first_x_layers = 1
filament_end_gcode = ;filament end gcode
filament_flow_ratio = 0.95
reduce_fan_stop_start_freq = 1
fan_cooling_layer_time = 100
filament_cost = 30
filament_density = 1.24
filament_deretraction_speed = nil
filament_diameter = 1.75
filament_max_volumetric_speed = 23
filament_minimal_purge_on_wipe_tower = 15
filament_retraction_minimum_travel = nil
filament_retract_before_wipe = nil
filament_retract_when_changing_layer = nil
filament_retraction_length = 1.2
filament_z_hop = 0.2
filament_z_hop_types = Slope Lift
filament_retract_restart_extra = 0
filament_retraction_speed = 40
filament_settings_id =
filament_soluble = 0
filament_type = PLA
filament_vendor = Creality
filament_wipe = nil
filament_wipe_distance = nil
bed_type = Cool Plate
nozzle_temperature_initial_layer = 190
full_fan_speed_layer = 0
fan_max_speed = 100
fan_min_speed = 100
slow_down_min_speed = 20
slow_down_layer_time = 6
filament_start_gcode = ;filament start gcode
nozzle_temperature = 190
temperature_vitrification = 100
filament_adhesiveness_category = 100
nozzle_temperature_range_low = 190
nozzle_temperature_range_high = 240
additional_cooling_fan_speed = 0
activate_air_filtration = 0
activate_chamber_temp_control = 0
chamber_temperature = 0
complete_print_exhaust_fan_speed = 80
cool_cds_fan_start_at_height = 0
cool_special_cds_fan_speed = 0
default_filament_colour = ""
during_print_exhaust_fan_speed = 60
enable_overhang_bridge_fan = 1
enable_pressure_advance = 0
enable_special_area_additional_cooling_fan = 0
epoxy_resin_plate_temp = 0
epoxy_resin_plate_temp_initial_layer = 0
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_is_support = 0
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_multitool_ramming = 0
filament_multitool_ramming_flow = 10
filament_multitool_ramming_volume = 10
filament_notes = ""
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_lift_above = 0
filament_retract_lift_below = 0
filament_retract_lift_enforce = All Surfaces
filament_shrink = 100%
filament_toolchange_delay = 0
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
material_flow_dependent_temperature = 0
material_flow_temp_graph = [[3.5,200],[7.0,240]]
pressure_advance = 0.02
required_nozzle_HRC = 0
support_material_interface_fan_speed = -1

97
print_config/prusa_slicer/materials/Hyper_Stardust_PLA.ini Normal file
View File

@@ -0,0 +1,97 @@
[metadata]
show_name = Hyper Stardust PLA
material_type = pla
[settings]
cool_plate_temp = 50
eng_plate_temp = 45
hot_plate_temp = 50
textured_plate_temp = 50
cool_plate_temp_initial_layer = 50
eng_plate_temp_initial_layer = 45
hot_plate_temp_initial_layer = 50
textured_plate_temp_initial_layer = 50
overhang_fan_threshold = 50%
overhang_fan_speed = 100
slow_down_for_layer_cooling = 1
close_fan_the_first_x_layers = 1
filament_end_gcode = ;filament end gcode
filament_flow_ratio = 0.95
reduce_fan_stop_start_freq = 1
fan_cooling_layer_time = 100
filament_cost = 26.9
filament_density = 1.24
filament_deretraction_speed = 15
filament_diameter = 1.75
filament_max_volumetric_speed = 18
filament_minimal_purge_on_wipe_tower = 15
filament_retraction_minimum_travel = 2
filament_retract_before_wipe = nil
filament_retract_when_changing_layer = nil
filament_retraction_length = 2
filament_z_hop = nil
filament_z_hop_types = nil
filament_retract_restart_extra = nil
filament_retraction_speed = 15
filament_settings_id =
filament_soluble = 0
filament_type = PLA
filament_vendor = Creality
filament_wipe = nil
filament_wipe_distance = 3
bed_type = Cool Plate
nozzle_temperature_initial_layer = 220
full_fan_speed_layer = 0
fan_max_speed = 100
fan_min_speed = 100
slow_down_min_speed = 10
slow_down_layer_time = 14
filament_start_gcode = ;filament start gcode
nozzle_temperature = 220
temperature_vitrification = 60
filament_adhesiveness_category = 100
nozzle_temperature_range_low = 190
nozzle_temperature_range_high = 240
additional_cooling_fan_speed = 0
activate_air_filtration = 0
activate_chamber_temp_control = 0
chamber_temperature = 0
complete_print_exhaust_fan_speed = 80
cool_cds_fan_start_at_height = 0.5
cool_special_cds_fan_speed = 0
customized_plate_temp = 50
customized_plate_temp_initial_layer = 50
default_filament_colour = ""
during_print_exhaust_fan_speed = 60
enable_overhang_bridge_fan = 1
enable_pressure_advance = 1
enable_special_area_additional_cooling_fan = 0
epoxy_resin_plate_temp = 50
epoxy_resin_plate_temp_initial_layer = 50
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_is_support = 0
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_multitool_ramming = 0
filament_multitool_ramming_flow = 10
filament_multitool_ramming_volume = 10
filament_notes = ""
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_lift_enforce = nil
filament_shrink = 100%
filament_shrinkage_compensation_z = 100%
filament_toolchange_delay = 0
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
material_flow_dependent_temperature = 0
material_flow_temp_graph = [[0.8,200],[1.0,200],[1.2,220]]
pressure_advance = 0.04
required_nozzle_HRC = 0
support_material_interface_fan_speed = -1

97
print_config/prusa_slicer/materials/Soleyin_Ultra_PLA.ini Normal file
View File

@@ -0,0 +1,97 @@
[metadata]
show_name = Soleyin Ultra PLA
material_type = pla
[settings]
cool_plate_temp = 50
eng_plate_temp = 45
hot_plate_temp = 50
textured_plate_temp = 50
cool_plate_temp_initial_layer = 50
eng_plate_temp_initial_layer = 45
hot_plate_temp_initial_layer = 50
textured_plate_temp_initial_layer = 50
overhang_fan_threshold = 50%
overhang_fan_speed = 100
slow_down_for_layer_cooling = 1
close_fan_the_first_x_layers = 1
filament_end_gcode = ;filament end gcode
filament_flow_ratio = 0.96
reduce_fan_stop_start_freq = 1
fan_cooling_layer_time = 100
filament_cost = 6
filament_density = 1.25
filament_deretraction_speed = 15
filament_diameter = 1.75
filament_max_volumetric_speed = 16
filament_minimal_purge_on_wipe_tower = 15
filament_retraction_minimum_travel = nil
filament_retract_before_wipe = 90%
filament_retract_when_changing_layer = nil
filament_retraction_length = nil
filament_z_hop = nil
filament_z_hop_types = nil
filament_retract_restart_extra = nil
filament_retraction_speed = 15
filament_settings_id =
filament_soluble = 0
filament_type = PLA
filament_vendor = Creality
filament_wipe = nil
filament_wipe_distance = nil
bed_type = Cool Plate
nozzle_temperature_initial_layer = 220
full_fan_speed_layer = 0
fan_max_speed = 100
fan_min_speed = 100
slow_down_min_speed = 20
slow_down_layer_time = 12
filament_start_gcode = ;filament start gcode
nozzle_temperature = 220
temperature_vitrification = 60
filament_adhesiveness_category = 100
nozzle_temperature_range_low = 190
nozzle_temperature_range_high = 240
additional_cooling_fan_speed = 0
activate_air_filtration = 0
activate_chamber_temp_control = 0
chamber_temperature = 0
complete_print_exhaust_fan_speed = 80
cool_cds_fan_start_at_height = 0
cool_special_cds_fan_speed = 0
customized_plate_temp = 60
customized_plate_temp_initial_layer = 60
default_filament_colour = ""
during_print_exhaust_fan_speed = 60
enable_overhang_bridge_fan = 1
enable_pressure_advance = 1
enable_special_area_additional_cooling_fan = 0
epoxy_resin_plate_temp = 60
epoxy_resin_plate_temp_initial_layer = 60
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_is_support = 0
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_multitool_ramming = 0
filament_multitool_ramming_flow = 10
filament_multitool_ramming_volume = 10
filament_notes = ""
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_lift_enforce = nil
filament_shrink = 100%
filament_shrinkage_compensation_z = 100%
filament_toolchange_delay = 0
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
material_flow_dependent_temperature = 0
material_flow_temp_graph = [[1.0,200],[1.1,200],[1.2,220]]
pressure_advance = 0.05
required_nozzle_HRC = 0
support_material_interface_fan_speed = -1

104
print_config/prusa_slicer/printers/Ender3_V3_SE.ini Normal file
View File

@@ -0,0 +1,104 @@
[metadata]
show_name = Ender3 V3 SE Model
[settings]
family = Creality
printer_technology = FFF
deretraction_speed = 30
extruder_colour = #FCE94F
extruder_offset = 0x0
gcode_flavor = marlin2
silent_mode = 0
support_chamber_temp_control = 0
support_air_filtration = 0
machine_max_acceleration_e = 5000,5000
machine_max_acceleration_extruding = 5000,5000
machine_max_acceleration_retracting = 2500,2500
machine_max_acceleration_x = 5000,5000
machine_max_acceleration_y = 5000,5000
machine_max_acceleration_z = 500,500
machine_max_speed_e = 100,100
machine_max_speed_x = 500,500
machine_max_speed_y = 500,500
machine_max_speed_z = 30,30
machine_max_jerk_e = 5,5
machine_max_jerk_x = 10,10
machine_max_jerk_y = 10,10
machine_max_jerk_z = 0.4,0.4
machine_min_extruding_rate = 0,0
machine_min_travel_rate = 0,0
max_layer_height = 0.36
min_layer_height = 0.08
printable_height = 250
extruder_clearance_radius = 90
extruder_clearance_height_to_rod = 47
extruder_clearance_height_to_lid = 34
nozzle_diameter = 0.4
printer_settings_id =
printer_variant = 0.4
retraction_minimum_travel = 1
retract_before_wipe = 100
retract_when_changing_layer = 1
retraction_length = 0.8
retract_length_toolchange = 1
z_hop = 0.4
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retraction_speed = 30
single_extruder_multi_material = 1
change_filament_gcode =
wipe = 1
z_hop_types = Slope Lift
before_layer_change_gcode = ;BEFORE_LAYER_CHANGE\n;[layer_z]\nG92 E0\n
default_print_profile = 0.20mm Standard @Creality Ender-3 V3 SE 0.4 nozzle
machine_start_gcode = M220 S100 ;Reset Feedrate \nM221 S100 ;Reset Flowrate \n \nM140 S[bed_temperature_initial_layer_single] ;Set final bed temp \nG28 ;Home \n \nG92 E0 ;Reset Extruder \nG1 Z2.0 F3000 ;Move Z Axis up \nM104 S[nozzle_temperature_initial_layer] ;Set final nozzle temp \nG1 X-2.1 Y20 Z0.28 F5000.0 ;Move to start position \nM190 S[bed_temperature_initial_layer_single] ;Wait for bed temp to stabilize \nM109 S[nozzle_temperature_initial_layer] ;Wait for nozzle temp to stabilize \nG1 X-2.1 Y145.0 Z0.28 F1500.0 E15 ;Draw the first line \nG1 X-2.4 Y145.0 Z0.28 F5000.0 ;Move to side a little \nG1 X-2.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line \nG92 E0 ;Reset Extruder \nG1 E-1.0000 F1800 ;Retract a bit \nG1 Z2.0 F3000 ;Move Z Axis up \nG1 E0.0000 F1800
machine_end_gcode = G91 ;Relative positionning \nG1 E-2 F2700 ;Retract a bit \nG1 E-2 Z0.2 F2400 ;Retract and raise Z \nG1 X5 Y5 F3000 ;Wipe out \nG1 Z10 ;Raise Z more \nG90 ;Absolute positionning \n \nG1 X0 Y220 ;Present print \nM106 S0 ;Turn-off fan \nM104 S0 ;Turn-off hotend \nM140 S0 ;Turn-off bed \n \nM84 X Y E ;Disable all steppers but Z
machine_max_acceleration_travel = 5000,5000
machine_pause_gcode = M25
bed_exclude_area = 0x0
layer_change_gcode =
scan_first_layer = 0
nozzle_type = brass
auxiliary_fan = 0
printer_model = Creality Ender-3 V3 SE
printer_structure = i3
bbl_use_printhost = 0
bed_mesh_max = 99999,99999
bed_mesh_min = -99999,-99999
bed_mesh_probe_distance = 50,50
best_object_pos = 0.5,0.5
cooling_tube_length = 5
cooling_tube_retraction = 91.5
creality_flush_time = 86.0
disable_m73 = 0
emit_machine_limits_to_gcode = 1
enable_filament_ramming = 1
extra_loading_move = -2
fan_kickstart = 0
fan_speedup_overhangs = 1
fan_speedup_time = 0
high_current_on_filament_swap = 0
machine_LED_light_exist = 0
machine_load_filament_time = 11
machine_platform_motion_enable = 0
machine_unload_filament_time = 0
manual_filament_change = 1
nozzle_hrc = 0
nozzle_volume = 0
parking_pos_retraction = 92
preferred_orientation = 0
printable_area = 0x0,220x0,220x220,0x220
purge_in_prime_tower = 1
support_multi_bed_types = 1
time_cost = 0
use_firmware_retraction = 0
use_relative_e_distances = 1
z_offset = 0
retract_lift_above = 0
retract_lift_below = 0
retract_lift_enforce = All Surfaces
wipe_distance = 2

216
print_config/prusa_slicer/quality/0.08mm_Extra_Fine.ini Normal file
View File

@@ -0,0 +1,216 @@
[metadata]
show_name = 0.08mm Extra Fine Quality
[settings]
adaptive_layer_height = 0
reduce_crossing_wall = 0
bridge_flow = 0.8
bridge_speed = 25
brim_width = 5
print_sequence = by layer
default_acceleration = 2500
bridge_no_support = 0
elefant_foot_compensation = 0.15
outer_wall_line_width = 0.42
outer_wall_speed = 60
line_width = 0.46
infill_direction = 45
sparse_infill_density = 10%
sparse_infill_pattern = zig-zag
initial_layer_line_width = 0.46
initial_layer_print_height = 0.2
initial_layer_speed = 60
gap_infill_speed = 50
infill_combination = 0
sparse_infill_line_width = 0.45
infill_wall_overlap = 15%
sparse_infill_speed = 180
interface_shells = 0
detect_overhang_wall = 1
reduce_infill_retraction = 1
wall_loops = 2
inner_wall_line_width = 0.45
inner_wall_speed = 90
print_settings_id =
raft_layers = 0
seam_position = aligned
skirt_distance = 2
skirt_height = 2
minimum_sparse_infill_area = 10
internal_solid_infill_line_width = 0.42
internal_solid_infill_speed = 180
spiral_mode = 0
standby_temperature_delta = -5
detect_thin_wall = 1
top_surface_line_width = 0.42
top_surface_speed = 50
travel_speed = 150
enable_prime_tower = 0
prime_tower_width = 60
xy_hole_compensation = 0
xy_contour_compensation = 0
max_travel_detour_distance = 0
bottom_surface_pattern = monotonic
bottom_shell_layers = 7
bottom_shell_thickness = 0
brim_object_gap = 0.1
compatible_printers_condition =
top_surface_acceleration = 2500
draft_shield = disabled
enable_arc_fitting = 0
wall_infill_order = inner wall/outer wall/infill
initial_layer_acceleration = 500
travel_acceleration = 2500
inner_wall_acceleration = 2000
ironing_flow = 15%
ironing_spacing = 0.1
ironing_speed = 20
ironing_type = no ironing
layer_height = 0.08
overhang_1_4_speed = 0
overhang_2_4_speed = 20
overhang_3_4_speed = 15
overhang_4_4_speed = 10
skirt_loops = 0
resolution = 0.012
top_surface_pattern = monotonicline
top_shell_layers = 9
top_shell_thickness = 0.8
initial_layer_infill_speed = 80
wipe_tower_no_sparse_layers = 0
accel_to_decel_enable = 1
accel_to_decel_factor = 50%
acceleration_limit_mess = [[0.5,1.0,100,6000],[1.0,1.5,80,5500],[1.5,2.0,60,5000]]
acceleration_limit_mess_enable = 0
alternate_extra_wall = 0
bottom_solid_infill_flow_ratio = 1
bridge_acceleration = 50%
bridge_angle = 0
bridge_density = 100%
brim_ears_detection_length = 1
brim_ears_max_angle = 125
brim_type = no_brim
default_jerk = 8
detect_narrow_internal_solid_infill = 1
elefant_foot_compensation_layers = 1
enable_overhang_speed = 1
enforce_support_layers = 0
ensure_vertical_shell_thickness = ensure_all
exclude_object = 0
extra_perimeters_on_overhangs = 0
filter_out_gap_fill = 0
flush_into_infill = 0
flush_into_objects = 0
flush_into_support = 1
fuzzy_skin = none
fuzzy_skin_first_layer = 0
fuzzy_skin_point_distance = 0.8
fuzzy_skin_thickness = 0.3
gcode_add_line_number = 0
gcode_comments = 0
gcode_label_objects = 1
hole_to_polyhole = 0
hole_to_polyhole_threshold = 0.01
hole_to_polyhole_twisted = 1
independent_support_layer_height = 1
infill_anchor = 400%
infill_anchor_max = 20
infill_jerk = 20
initial_layer_jerk = 8
initial_layer_min_bead_width = 85%
initial_layer_travel_speed = 100%
inner_wall_jerk = 20
internal_bridge_flow = 1
internal_bridge_speed = 150%
internal_solid_infill_acceleration = 100%
internal_solid_infill_pattern = monotonic
ironing_angle = -1
ironing_pattern = zig-zag
ironing_support_layer = 0
is_infill_first = 0
make_overhang_printable = 0
make_overhang_printable_angle = 55
make_overhang_printable_hole_size = 0
max_bridge_length = 10
max_volumetric_extrusion_rate_slope = 0
max_volumetric_extrusion_rate_slope_segment_length = 3
min_bead_width = 85%
min_feature_size = 25%
min_width_top_surface = 300%
minimum_support_area = 5
mmu_segmented_region_interlocking_depth = 0
mmu_segmented_region_max_width = 0
only_one_wall_first_layer = 0
only_one_wall_top = 0
ooze_prevention = 0
outer_wall_acceleration = 1000
outer_wall_jerk = 20
overhang_reverse = 0
overhang_reverse_internal_only = 0
overhang_reverse_threshold = 50%
overhang_speed_classic = 0
precise_outer_wall = 0
prime_tower_brim_width = 3
prime_tower_enhance_type = chamfer
prime_volume = 45
print_flow_ratio = 1
print_order = default
raft_contact_distance = 0.1
raft_expansion = 1.5
raft_first_layer_density = 90%
raft_first_layer_expansion = 2
role_based_wipe_speed = 1
scarf_angle_threshold = 155
scarf_joint_flow_ratio = 1
scarf_joint_speed = 100%
scarf_overhang_threshold = 40%
seam_gap = 10%
seam_slope_conditional = 0
seam_slope_entire_loop = 0
seam_slope_inner_walls = 0
seam_slope_min_length = 20
seam_slope_start_height = 0
seam_slope_steps = 10
seam_slope_type = none
single_extruder_multi_material_priming = 0
skirt_speed = 50
slice_closing_radius = 0.049
slicing_mode = regular
slow_down_layers = 0
slowdown_for_curled_perimeters = 0
small_area_infill_flow_compensation = 0
small_area_infill_flow_compensation_model = 0,0;\n0.2,0.4444;\n0.4,0.6145;\n0.6,0.7059;\n0.8,0.7619;\n1.5,0.8571;\n2,0.8889;\n3,0.9231;\n5,0.9520;\n10,1
small_perimeter_speed = 50%
small_perimeter_threshold = 0
solid_infill_filament = 1
sparse_infill_acceleration = 100%
sparse_infill_filament = 1
speed_limit_to_height = [[100,150,200,6000],[150,200,200,4000],[200,250,200,2000]]
speed_limit_to_height_enable = 0
spiral_mode_max_xy_smoothing = 200%
spiral_mode_smooth = 0
staggered_inner_seams = 1
thick_bridges = 0
thick_internal_bridges = 1
timelapse_type = 0
top_solid_infill_flow_ratio = 1
top_surface_jerk = 9
travel_jerk = 12
travel_speed_z = 0
wall_direction = auto
wall_distribution_count = 1
wall_filament = 1
wall_generator = arachne
wall_sequence = inner wall/outer wall
wall_transition_angle = 10
wall_transition_filter_deviation = 25%
wall_transition_length = 100%
wipe_before_external_loop = 0
wipe_on_loops = 0
wipe_speed = 80%
wipe_tower_bridging = 10
wipe_tower_cone_angle = 0
wipe_tower_extra_spacing = 100%
wipe_tower_rotation_angle = 0
wiping_volumes_extruders = 70,70,70,70,70,70,70,70,70,70

200
print_config/prusa_slicer/quality/0.12mm_Fine.ini Normal file
View File

@@ -0,0 +1,200 @@
[metadata]
show_name = 0.12mm Fine Quality
[settings]
adaptive_layer_height = 0
reduce_crossing_wall = 0
bridge_flow = 0.95
bridge_speed = 100
brim_width = 5
print_sequence = by layer
default_acceleration = 2500
bridge_no_support = 0
elefant_foot_compensation = 0
outer_wall_line_width = 0.42
outer_wall_speed = 60
line_width = 0.46
infill_direction = 45
sparse_infill_density = 15%
sparse_infill_pattern = grid
initial_layer_line_width = 0.46
initial_layer_print_height = 0.2
initial_layer_speed = 30
gap_infill_speed = 50
infill_combination = 0
sparse_infill_line_width = 0.45
infill_wall_overlap = 15%
sparse_infill_speed = 180
interface_shells = 0
detect_overhang_wall = 1
reduce_infill_retraction = 1
wall_loops = 2
inner_wall_line_width = 0.45
inner_wall_speed = 90
print_settings_id =
raft_layers = 0
seam_position = aligned
skirt_distance = 2
skirt_height = 2
minimum_sparse_infill_area = 10
internal_solid_infill_line_width = 0.42
internal_solid_infill_speed = 180
spiral_mode = 0
standby_temperature_delta = -5
detect_thin_wall = 1
top_surface_line_width = 0.42
top_surface_speed = 50
travel_speed = 150
enable_prime_tower = 0
prime_tower_width = 60
xy_hole_compensation = 0
xy_contour_compensation = 0
max_travel_detour_distance = 0
bottom_surface_pattern = monotonic
bottom_shell_layers = 5
bottom_shell_thickness = 0
brim_object_gap = 0.1
compatible_printers_condition =
top_surface_acceleration = 2500
draft_shield = disabled
enable_arc_fitting = 0
wall_infill_order = inner wall/outer wall/infill
initial_layer_acceleration = 500
travel_acceleration = 2500
inner_wall_acceleration = 2000
ironing_flow = 15%
ironing_spacing = 0.1
ironing_speed = 20
ironing_type = no ironing
layer_height = 0.12
overhang_1_4_speed = 0
overhang_2_4_speed = 20
overhang_3_4_speed = 15
overhang_4_4_speed = 10
skirt_loops = 0
resolution = 0.012
top_surface_pattern = monotonic
top_shell_layers = 5
top_shell_thickness = 0.8
initial_layer_infill_speed = 80
wipe_tower_no_sparse_layers = 0
accel_to_decel_enable = 1
accel_to_decel_factor = 50%
acceleration_limit_mess = [[0.5,1.0,100,6000],[1.0,1.5,80,5500],[1.5,2.0,60,5000]]
acceleration_limit_mess_enable = 0
alternate_extra_wall = 0
bottom_solid_infill_flow_ratio = 1
bridge_acceleration = 50%
bridge_angle = 0
bridge_density = 100%
brim_ears_detection_length = 1
brim_ears_max_angle = 125
brim_type = no_brim
default_jerk = 8
detect_narrow_internal_solid_infill = 1
elefant_foot_compensation_layers = 1
enable_overhang_speed = 1
enforce_support_layers = 0
ensure_vertical_shell_thickness = ensure_all
exclude_object = 0
extra_perimeters_on_overhangs = 0
filter_out_gap_fill = 0
flush_into_infill = 0
flush_into_objects = 0
flush_into_support = 1
fuzzy_skin = none
fuzzy_skin_first_layer = 0
fuzzy_skin_point_distance = 0.8
fuzzy_skin_thickness = 0.3
gcode_add_line_number = 0
gcode_comments = 0
gcode_label_objects = 1
hole_to_polyhole = 0
hole_to_polyhole_threshold = 0.01
hole_to_polyhole_twisted = 1
independent_support_layer_height = 1
infill_anchor = 400%
infill_anchor_max = 20
infill_jerk = 20
initial_layer_jerk = 8
initial_layer_min_bead_width = 85%
initial_layer_travel_speed = 100%
inner_wall_jerk = 20
internal_bridge_flow = 1
internal_bridge_speed = 150%
internal_solid_infill_acceleration = 100%
internal_solid_infill_pattern = monotonic
ironing_angle = -1
ironing_pattern = zig-zag
ironing_support_layer = 0
is_infill_first = 0
make_overhang_printable = 0
make_overhang_printable_angle = 55
make_overhang_printable_hole_size = 0
max_bridge_length = 10
max_volumetric_extrusion_rate_slope = 0
max_volumetric_extrusion_rate_slope_segment_length = 3
min_bead_width = 85%
min_feature_size = 25%
min_width_top_surface = 300%
minimum_support_area = 5
mmu_segmented_region_interlocking_depth = 0
mmu_segmented_region_max_width = 0
only_one_wall_first_layer = 0
only_one_wall_top = 0
ooze_prevention = 0
outer_wall_acceleration = 1000
outer_wall_jerk = 20
overhang_reverse = 0
overhang_reverse_internal_only = 0
overhang_reverse_threshold = 50%
overhang_speed_classic = 0
precise_outer_wall = 0
prime_tower_brim_width = 3
prime_volume = 45
print_flow_ratio = 1
raft_contact_distance = 0.1
raft_expansion = 1.5
raft_first_layer_density = 90%
raft_first_layer_expansion = 2
role_based_wipe_speed = 1
seam_gap = 10%
single_extruder_multi_material_priming = 0
skirt_speed = 50
slice_closing_radius = 0.049
slicing_mode = regular
slow_down_layers = 0
slowdown_for_curled_perimeters = 0
small_perimeter_speed = 50%
small_perimeter_threshold = 0
solid_infill_filament = 1
sparse_infill_acceleration = 100%
sparse_infill_filament = 1
speed_limit_to_height = [[100,150,100,6000],[150,200,80,5500],[200,250,60,5000]]
speed_limit_to_height_enable = 0
spiral_mode_max_xy_smoothing = 200%
spiral_mode_smooth = 0
staggered_inner_seams = 0
thick_bridges = 0
thick_internal_bridges = 1
timelapse_type = 0
top_solid_infill_flow_ratio = 1
top_surface_jerk = 20
travel_jerk = 8
travel_speed_z = 0
wall_distribution_count = 1
wall_filament = 1
wall_generator = arachne
wall_sequence = inner wall/outer wall
wall_transition_angle = 10
wall_transition_filter_deviation = 25%
wall_transition_length = 100%
wipe_before_external_loop = 0
wipe_on_loops = 0
wipe_speed = 80%
wipe_tower_bridging = 10
wipe_tower_cone_angle = 0
wipe_tower_extra_spacing = 100%
wipe_tower_rotation_angle = 0
wiping_volumes_extruders = 70,70,70,70,70,70,70,70,70,70

200
print_config/prusa_slicer/quality/0.16mm_Optimal.ini Normal file
View File

@@ -0,0 +1,200 @@
[metadata]
show_name = 0.16mm Optimal Quality
[settings]
adaptive_layer_height = 0
reduce_crossing_wall = 0
bridge_flow = 0.95
bridge_speed = 100
brim_width = 5
print_sequence = by layer
default_acceleration = 2500
bridge_no_support = 0
elefant_foot_compensation = 0
outer_wall_line_width = 0.42
outer_wall_speed = 60
line_width = 0.46
infill_direction = 45
sparse_infill_density = 15%
sparse_infill_pattern = grid
initial_layer_line_width = 0.46
initial_layer_print_height = 0.2
initial_layer_speed = 30
gap_infill_speed = 50
infill_combination = 0
sparse_infill_line_width = 0.45
infill_wall_overlap = 15%
sparse_infill_speed = 180
interface_shells = 0
detect_overhang_wall = 1
reduce_infill_retraction = 1
wall_loops = 2
inner_wall_line_width = 0.45
inner_wall_speed = 90
print_settings_id =
raft_layers = 0
seam_position = aligned
skirt_distance = 2
skirt_height = 2
minimum_sparse_infill_area = 10
internal_solid_infill_line_width = 0.42
internal_solid_infill_speed = 180
spiral_mode = 0
standby_temperature_delta = -5
detect_thin_wall = 1
top_surface_line_width = 0.42
top_surface_speed = 50
travel_speed = 150
enable_prime_tower = 0
prime_tower_width = 60
xy_hole_compensation = 0
xy_contour_compensation = 0
max_travel_detour_distance = 0
bottom_surface_pattern = monotonic
bottom_shell_layers = 4
bottom_shell_thickness = 0
brim_object_gap = 0.1
compatible_printers_condition =
top_surface_acceleration = 2500
draft_shield = disabled
enable_arc_fitting = 0
wall_infill_order = inner wall/outer wall/infill
initial_layer_acceleration = 500
travel_acceleration = 2500
inner_wall_acceleration = 2000
ironing_flow = 15%
ironing_spacing = 0.1
ironing_speed = 20
ironing_type = no ironing
layer_height = 0.16
overhang_1_4_speed = 0
overhang_2_4_speed = 20
overhang_3_4_speed = 15
overhang_4_4_speed = 10
skirt_loops = 0
resolution = 0.012
top_surface_pattern = monotonic
top_shell_layers = 6
top_shell_thickness = 0.8
initial_layer_infill_speed = 80
wipe_tower_no_sparse_layers = 0
accel_to_decel_enable = 1
accel_to_decel_factor = 50%
acceleration_limit_mess = [[0.5,1.0,100,6000],[1.0,1.5,80,5500],[1.5,2.0,60,5000]]
acceleration_limit_mess_enable = 0
alternate_extra_wall = 0
bottom_solid_infill_flow_ratio = 1
bridge_acceleration = 50%
bridge_angle = 0
bridge_density = 100%
brim_ears_detection_length = 1
brim_ears_max_angle = 125
brim_type = no_brim
default_jerk = 8
detect_narrow_internal_solid_infill = 1
elefant_foot_compensation_layers = 1
enable_overhang_speed = 1
enforce_support_layers = 0
ensure_vertical_shell_thickness = ensure_all
exclude_object = 0
extra_perimeters_on_overhangs = 0
filter_out_gap_fill = 0
flush_into_infill = 0
flush_into_objects = 0
flush_into_support = 1
fuzzy_skin = none
fuzzy_skin_first_layer = 0
fuzzy_skin_point_distance = 0.8
fuzzy_skin_thickness = 0.3
gcode_add_line_number = 0
gcode_comments = 0
gcode_label_objects = 1
hole_to_polyhole = 0
hole_to_polyhole_threshold = 0.01
hole_to_polyhole_twisted = 1
independent_support_layer_height = 1
infill_anchor = 400%
infill_anchor_max = 20
infill_jerk = 20
initial_layer_jerk = 8
initial_layer_min_bead_width = 85%
initial_layer_travel_speed = 100%
inner_wall_jerk = 20
internal_bridge_flow = 1
internal_bridge_speed = 150%
internal_solid_infill_acceleration = 100%
internal_solid_infill_pattern = monotonic
ironing_angle = -1
ironing_pattern = zig-zag
ironing_support_layer = 0
is_infill_first = 0
make_overhang_printable = 0
make_overhang_printable_angle = 55
make_overhang_printable_hole_size = 0
max_bridge_length = 10
max_volumetric_extrusion_rate_slope = 0
max_volumetric_extrusion_rate_slope_segment_length = 3
min_bead_width = 85%
min_feature_size = 25%
min_width_top_surface = 300%
minimum_support_area = 5
mmu_segmented_region_interlocking_depth = 0
mmu_segmented_region_max_width = 0
only_one_wall_first_layer = 0
only_one_wall_top = 0
ooze_prevention = 0
outer_wall_acceleration = 1000
outer_wall_jerk = 20
overhang_reverse = 0
overhang_reverse_internal_only = 0
overhang_reverse_threshold = 50%
overhang_speed_classic = 0
precise_outer_wall = 0
prime_tower_brim_width = 3
prime_volume = 45
print_flow_ratio = 1
raft_contact_distance = 0.1
raft_expansion = 1.5
raft_first_layer_density = 90%
raft_first_layer_expansion = 2
role_based_wipe_speed = 1
seam_gap = 10%
single_extruder_multi_material_priming = 0
skirt_speed = 50
slice_closing_radius = 0.049
slicing_mode = regular
slow_down_layers = 0
slowdown_for_curled_perimeters = 0
small_perimeter_speed = 50%
small_perimeter_threshold = 0
solid_infill_filament = 1
sparse_infill_acceleration = 100%
sparse_infill_filament = 1
speed_limit_to_height = [[100,150,100,6000],[150,200,80,5500],[200,250,60,5000]]
speed_limit_to_height_enable = 0
spiral_mode_max_xy_smoothing = 200%
spiral_mode_smooth = 0
staggered_inner_seams = 0
thick_bridges = 0
thick_internal_bridges = 1
timelapse_type = 0
top_solid_infill_flow_ratio = 1
top_surface_jerk = 20
travel_jerk = 8
travel_speed_z = 0
wall_distribution_count = 1
wall_filament = 1
wall_generator = arachne
wall_sequence = inner wall/outer wall
wall_transition_angle = 10
wall_transition_filter_deviation = 25%
wall_transition_length = 100%
wipe_before_external_loop = 0
wipe_on_loops = 0
wipe_speed = 80%
wipe_tower_bridging = 10
wipe_tower_cone_angle = 0
wipe_tower_extra_spacing = 100%
wipe_tower_rotation_angle = 0
wiping_volumes_extruders = 70,70,70,70,70,70,70,70,70,70

226
print_config/prusa_slicer/quality/0.20mm_Standard.ini Normal file
View File

@@ -0,0 +1,226 @@
[metadata]
show_name = 0.20mm Standard Quality
[settings]
adaptive_layer_height = 0
reduce_crossing_wall = 0
bridge_flow = 0.95
bridge_speed = 50
brim_width = 5
print_sequence = by layer
default_acceleration = 2500
bridge_no_support = 0
elefant_foot_compensation = 0.15
outer_wall_line_width = 0.42
outer_wall_speed = 60
line_width = 0.45
infill_direction = 45
sparse_infill_density = 15%
sparse_infill_pattern = zig-zag
initial_layer_line_width = 0.5
initial_layer_print_height = 0.2
initial_layer_speed = 30
gap_infill_speed = 50
infill_combination = 0
sparse_infill_line_width = 0.45
infill_wall_overlap = 30
sparse_infill_speed = 180
interface_shells = 0
detect_overhang_wall = 1
reduce_infill_retraction = 1
wall_loops = 2
inner_wall_line_width = 0.45
inner_wall_speed = 90
print_settings_id =
raft_layers = 0
seam_position = aligned
skirt_distance = 2
skirt_height = 2
minimum_sparse_infill_area = 10
internal_solid_infill_line_width = 0.42
internal_solid_infill_speed = 180
spiral_mode = 0
standby_temperature_delta = -5
detect_thin_wall = 0
top_surface_line_width = 0.42
top_surface_speed = 50
travel_speed = 150
enable_prime_tower = 0
prime_tower_width = 60
xy_hole_compensation = 0
xy_contour_compensation = 0
max_travel_detour_distance = 0
bottom_surface_pattern = monotonic
bottom_shell_layers = 4
bottom_shell_thickness = 0
brim_object_gap = 0.1
compatible_printers_condition =
top_surface_acceleration = 2500
draft_shield = disabled
enable_arc_fitting = 1
wall_infill_order = inner wall/outer wall/infill
initial_layer_acceleration = 500
travel_acceleration = 2500
inner_wall_acceleration = 2000
ironing_flow = 15%
ironing_spacing = 0.1
ironing_speed = 20
ironing_type = no ironing
layer_height = 0.2
overhang_1_4_speed = 0
overhang_2_4_speed = 60
overhang_3_4_speed = 30
overhang_4_4_speed = 10
skirt_loops = 0
resolution = 0.012
top_surface_pattern = monotonic
top_shell_layers = 4
top_shell_thickness = 0.8
initial_layer_infill_speed = 80
wipe_tower_no_sparse_layers = 0
accel_to_decel_enable = 1
accel_to_decel_factor = 25
acceleration_limit_mess = [[0.5,1.0,100,6000],[1.0,1.5,80,5500],[1.5,2.0,60,5000]]
acceleration_limit_mess_enable = 0
ai_infill = 0
alternate_extra_wall = 0
bottom_solid_infill_flow_ratio = 1
bridge_acceleration = 50%
bridge_angle = 0
bridge_density = 100%
brim_ears_detection_length = 1
brim_ears_max_angle = 125
brim_type = no_brim
counterbore_hole_bridging = none
default_jerk = 10
detect_narrow_internal_solid_infill = 1
dont_filter_internal_bridges = disabled
elefant_foot_compensation_layers = 1
enable_overhang_speed = 1
enforce_support_layers = 0
ensure_vertical_shell_thickness = ensure_all
exclude_object = 0
extra_perimeters_on_overhangs = 0
filter_out_gap_fill = 0
flush_into_infill = 0
flush_into_objects = 0
flush_into_support = 1
fuzzy_skin = none
fuzzy_skin_first_layer = 0
fuzzy_skin_point_distance = 0.8
fuzzy_skin_thickness = 0.3
gap_fill_target = everywhere
gcode_add_line_number = 0
gcode_comments = 0
gcode_label_objects = 1
hole_to_polyhole = 0
hole_to_polyhole_threshold = 0.01
hole_to_polyhole_twisted = 1
independent_support_layer_height = 1
infill_anchor = 400%
infill_anchor_max = 20
infill_jerk = 10
initial_layer_jerk = 10
initial_layer_min_bead_width = 85%
initial_layer_travel_speed = 100%
inner_wall_jerk = 10
internal_bridge_flow = 1
internal_bridge_speed = 150%
internal_solid_infill_acceleration = 100%
internal_solid_infill_pattern = monotonic
ironing_angle = -1
ironing_pattern = zig-zag
ironing_support_layer = 0
is_infill_first = 0
make_overhang_printable = 0
make_overhang_printable_angle = 55
make_overhang_printable_hole_size = 0
material_flow_dependent_temperature = 0
material_flow_temp_graph = [[3.0,210],[10.0,220],[12.0,230]]
max_bridge_length = 10
max_volumetric_extrusion_rate_slope = 0
max_volumetric_extrusion_rate_slope_segment_length = 3
min_bead_width = 85%
min_feature_size = 25%
min_length_factor = 0.5
min_width_top_surface = 300%
minimum_support_area = 5
mmu_segmented_region_interlocking_depth = 0
mmu_segmented_region_max_width = 0
only_one_wall_first_layer = 0
only_one_wall_top = 1
ooze_prevention = 0
outer_wall_acceleration = 1000
outer_wall_jerk = 10
overhang_reverse = 0
overhang_reverse_internal_only = 0
overhang_reverse_threshold = 50%
overhang_speed_classic = 0
precise_outer_wall = 0
prime_tower_brim_width = 3
prime_tower_enhance_type = chamfer
prime_volume = 45
print_flow_ratio = 1
print_order = default
raft_contact_distance = 0.1
raft_expansion = 1.5
raft_first_layer_density = 90%
raft_first_layer_expansion = 2
role_based_wipe_speed = 0
scarf_angle_threshold = 155
scarf_joint_flow_ratio = 1
scarf_joint_speed = 100%
scarf_overhang_threshold = 40%
seam_gap = 10%
seam_slope_conditional = 0
seam_slope_entire_loop = 0
seam_slope_inner_walls = 0
seam_slope_min_length = 20
seam_slope_start_height = 0
seam_slope_steps = 10
seam_slope_type = none
single_extruder_multi_material_priming = 0
skirt_speed = 50
slice_closing_radius = 0.049
slicing_mode = regular
slow_down_layers = 0
slowdown_for_curled_perimeters = 0
small_area_infill_flow_compensation = 0
small_area_infill_flow_compensation_model = 0,0;"\n0.2,0.4444";"\n0.4,0.6145";"\n0.6,0.7059";"\n0.8,0.7619";"\n1.5,0.8571";"\n2,0.8889";"\n3,0.9231";"\n5,0.9520";"\n10,1"
small_perimeter_speed = 50%
small_perimeter_threshold = 0
solid_infill_filament = 1
sparse_infill_acceleration = 100%
sparse_infill_filament = 1
speed_limit_to_height = [[100,150,100,6000],[150,200,80,5500],[200,250,60,5000]]
speed_limit_to_height_enable = 0
spiral_mode_max_xy_smoothing = 200%
spiral_mode_smooth = 0
staggered_inner_seams = 1
thick_bridges = 0
thick_internal_bridges = 1
timelapse_type = 0
top_solid_infill_flow_ratio = 1
top_surface_jerk = 8
travel_jerk = 10
travel_speed_z = 0
wall_direction = auto
wall_distribution_count = 1
wall_filament = 1
wall_generator = arachne
wall_sequence = inner wall/outer wall
wall_transition_angle = 10
wall_transition_filter_deviation = 25%
wall_transition_length = 100%
wipe_before_external_loop = 0
wipe_on_loops = 0
wipe_speed = 100%
wipe_tower_bridging = 10
wipe_tower_cone_angle = 0
wipe_tower_extra_spacing = 100%
wipe_tower_rotation_angle = 0
wiping_volumes_extruders = 70,70,70,70,70,70,70,70,70,70

50
print_config/prusa_slicer/supports/no_support.ini Normal file
View File

@@ -0,0 +1,50 @@
[metadata]
show_name = No Support
[settings]
enable_support = 0
support_filament = 0
support_line_width = 0.4
support_interface_filament = 0
support_on_build_plate_only = 0
support_top_z_distance = 0.2
support_interface_loop_pattern = 0
support_interface_top_layers = 2
support_interface_spacing = 0.5
support_interface_speed = 100%
support_base_pattern = rectilinear
support_base_pattern_spacing = 2.5
support_speed = 50
support_threshold_angle = 30
support_object_xy_distance = 0.35
support_type = normal(auto)
support_style = default
support_interface_bottom_layers = 2
tree_support_branch_angle = 45
tree_support_wall_count = 0
support_angle = 0
support_bottom_interface_spacing = 0.5
support_bottom_z_distance = 0.2
support_critical_regions_only = 0
support_expansion = 0
support_interface_not_for_body = 1
support_interface_pattern = auto
support_remove_small_overhang = 1
support_xy_overrides_z = xy_overrides_z
tree_support_adaptive_layer_height = 1
tree_support_angle_slow = 25
tree_support_auto_brim = 1
tree_support_branch_angle_organic = 40
tree_support_branch_diameter = 2
tree_support_branch_diameter_angle = 5
tree_support_branch_diameter_double_wall = 3
tree_support_branch_diameter_organic = 2
tree_support_branch_distance = 5
tree_support_branch_distance_organic = 1
tree_support_brim_width = 3
tree_support_tip_diameter = 0.8
tree_support_top_rate = 30%