tmp prusa配置文件集

Co-authored-by: Copilot <copilot@github.com>

print_config/prusa_slicer/materials/CR-PETG.ini

@@ -0,0 +1,94 @@
+[metadata]
+show_name = CR-PETG
+material_type = petg
+
+
+[settings]
+filament_adhesiveness_category = 300
+cool_plate_temp = 70
+eng_plate_temp = 0
+hot_plate_temp = 70
+textured_plate_temp = 70
+cool_plate_temp_initial_layer = 70
+eng_plate_temp_initial_layer = 0
+hot_plate_temp_initial_layer = 70
+textured_plate_temp_initial_layer = 70
+overhang_fan_threshold = 25%
+overhang_fan_speed = 90
+slow_down_for_layer_cooling = 1
+close_fan_the_first_x_layers = 3
+filament_end_gcode = ; filament end gcode \n
+filament_flow_ratio = 0.95
+reduce_fan_stop_start_freq = 1
+fan_cooling_layer_time = 30
+filament_cost = 14
+filament_density = 1.23
+filament_deretraction_speed = nil
+filament_diameter = 1.75
+filament_max_volumetric_speed = 9
+filament_minimal_purge_on_wipe_tower = 15
+filament_retraction_minimum_travel = nil
+filament_retract_before_wipe = nil
+filament_retract_when_changing_layer = nil
+filament_retraction_length = nil
+filament_z_hop = nil
+filament_z_hop_types = nil
+filament_retract_restart_extra = 0
+filament_retraction_speed = nil
+filament_settings_id = 
+filament_soluble = 0
+filament_type = PETG
+filament_vendor = Creality
+filament_wipe = nil
+filament_wipe_distance = nil
+bed_type = Cool Plate
+nozzle_temperature_initial_layer = 230
+full_fan_speed_layer = 0
+fan_max_speed = 40
+fan_min_speed = 30
+slow_down_min_speed = 10
+slow_down_layer_time = 8
+filament_start_gcode = ; filament start gcode\n
+nozzle_temperature = 230
+temperature_vitrification = 80
+activate_air_filtration = 0
+activate_chamber_temp_control = 0
+additional_cooling_fan_speed = 0
+chamber_temperature = 35
+complete_print_exhaust_fan_speed = 80
+cool_cds_fan_start_at_height = 0
+cool_special_cds_fan_speed = 0
+default_filament_colour = ""
+during_print_exhaust_fan_speed = 60
+enable_overhang_bridge_fan = 1
+enable_pressure_advance = 1
+enable_special_area_additional_cooling_fan = 0
+epoxy_resin_plate_temp = 70
+epoxy_resin_plate_temp_initial_layer = 70
+filament_cooling_final_speed = 3.4
+filament_cooling_initial_speed = 2.2
+filament_cooling_moves = 4
+filament_is_support = 0
+filament_load_time = 0
+filament_loading_speed = 28
+filament_loading_speed_start = 3
+filament_multitool_ramming = 0
+filament_multitool_ramming_flow = 10
+filament_multitool_ramming_volume = 10
+filament_notes = ""
+filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
+filament_retract_lift_above = 0
+filament_retract_lift_below = 0
+filament_retract_lift_enforce = All Surfaces
+filament_shrink = 100%
+filament_toolchange_delay = 0
+filament_unload_time = 0
+filament_unloading_speed = 90
+filament_unloading_speed_start = 100
+material_flow_dependent_temperature = 0
+material_flow_temp_graph = [[3.0,210],  [10.0,220],  [12.0,230]]
+nozzle_temperature_range_high = 270
+nozzle_temperature_range_low = 220
+pressure_advance = 0.08
+required_nozzle_HRC = 0
+support_material_interface_fan_speed = -1

print_config/prusa_slicer/materials/CR-PLA.ini

@@ -0,0 +1,94 @@
+[metadata]
+show_name = CR-PLA
+material_type = pla
+
+
+[settings]
+cool_plate_temp = 50
+eng_plate_temp = 45
+hot_plate_temp = 50
+textured_plate_temp = 50
+cool_plate_temp_initial_layer = 50
+eng_plate_temp_initial_layer = 45
+hot_plate_temp_initial_layer = 50
+textured_plate_temp_initial_layer = 50
+overhang_fan_threshold = 50%
+overhang_fan_speed = 100
+slow_down_for_layer_cooling = 1
+close_fan_the_first_x_layers = 1
+filament_end_gcode = ;filament end gcode 
+filament_flow_ratio = 0.95
+reduce_fan_stop_start_freq = 1
+fan_cooling_layer_time = 100
+filament_cost = 25
+filament_density = 1.25
+filament_deretraction_speed = nil
+filament_diameter = 1.75
+filament_max_volumetric_speed = 12
+filament_minimal_purge_on_wipe_tower = 15
+filament_retraction_minimum_travel = nil
+filament_retract_before_wipe = nil
+filament_retract_when_changing_layer = nil
+filament_retraction_length = 1
+filament_z_hop = 0.2
+filament_z_hop_types = Slope Lift
+filament_retract_restart_extra = 0
+filament_retraction_speed = 40
+filament_settings_id = 
+filament_soluble = 0
+filament_type = PLA
+filament_vendor = Creality
+filament_wipe = nil
+filament_wipe_distance = nil
+bed_type = Cool Plate
+nozzle_temperature_initial_layer = 190
+full_fan_speed_layer = 0
+fan_max_speed = 100
+fan_min_speed = 100
+slow_down_min_speed = 20
+slow_down_layer_time = 6
+filament_start_gcode = ;filament start gcode
+nozzle_temperature = 190
+temperature_vitrification = 100
+filament_adhesiveness_category = 100
+nozzle_temperature_range_low = 190
+nozzle_temperature_range_high = 240
+additional_cooling_fan_speed = 0
+activate_air_filtration = 0
+activate_chamber_temp_control = 0
+chamber_temperature = 0
+complete_print_exhaust_fan_speed = 80
+cool_cds_fan_start_at_height = 0
+cool_special_cds_fan_speed = 0
+default_filament_colour = ""
+during_print_exhaust_fan_speed = 60
+enable_overhang_bridge_fan = 1
+enable_pressure_advance = 0
+enable_special_area_additional_cooling_fan = 0
+epoxy_resin_plate_temp = 0
+epoxy_resin_plate_temp_initial_layer = 0
+filament_cooling_final_speed = 3.4
+filament_cooling_initial_speed = 2.2
+filament_cooling_moves = 4
+filament_is_support = 0
+filament_load_time = 0
+filament_loading_speed = 28
+filament_loading_speed_start = 3
+filament_multitool_ramming = 0
+filament_multitool_ramming_flow = 10
+filament_multitool_ramming_volume = 10
+filament_notes = ""
+filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
+filament_retract_lift_above = 0
+filament_retract_lift_below = 0
+filament_retract_lift_enforce = All Surfaces
+filament_shrink = 100%
+filament_toolchange_delay = 0
+filament_unload_time = 0
+filament_unloading_speed = 90
+filament_unloading_speed_start = 100
+material_flow_dependent_temperature = 0
+material_flow_temp_graph = [[2.0,185],[4.0,190],[7.0,200]]
+pressure_advance = 0.02
+required_nozzle_HRC = 0
+support_material_interface_fan_speed = -1

print_config/prusa_slicer/materials/Generic_PETG.ini

@@ -0,0 +1,94 @@
+[metadata]
+show_name = Generic PETG
+material_type = petg
+
+
+[settings]
+filament_adhesiveness_category = 300
+cool_plate_temp = 60
+eng_plate_temp = 0
+hot_plate_temp = 70
+textured_plate_temp = 70
+cool_plate_temp_initial_layer = 60
+eng_plate_temp_initial_layer = 0
+hot_plate_temp_initial_layer = 70
+textured_plate_temp_initial_layer = 70
+overhang_fan_threshold = 25%
+overhang_fan_speed = 90
+slow_down_for_layer_cooling = 1
+close_fan_the_first_x_layers = 3
+filament_end_gcode = ;filament end gcode \n
+filament_flow_ratio = 0.95
+reduce_fan_stop_start_freq = 1
+fan_cooling_layer_time = 30
+filament_cost = 30
+filament_density = 1.27
+filament_deretraction_speed = nil
+filament_diameter = 1.75
+filament_max_volumetric_speed = 10
+filament_minimal_purge_on_wipe_tower = 15
+filament_retraction_minimum_travel = nil
+filament_retract_before_wipe = nil
+filament_retract_when_changing_layer = nil
+filament_retraction_length = 1.2
+filament_z_hop = 0.2
+filament_z_hop_types = nil
+filament_retract_restart_extra = 0
+filament_retraction_speed = nil
+filament_settings_id = 
+filament_soluble = 0
+filament_type = PETG
+filament_vendor = Creality
+filament_wipe = nil
+filament_wipe_distance = nil
+bed_type = Cool Plate
+nozzle_temperature_initial_layer = 220
+full_fan_speed_layer = 0
+fan_max_speed = 80
+fan_min_speed = 40
+slow_down_min_speed = 10
+slow_down_layer_time = 8
+filament_start_gcode = ;filament start gcode\n
+nozzle_temperature = 220
+temperature_vitrification = 80
+activate_air_filtration = 0
+activate_chamber_temp_control = 0
+additional_cooling_fan_speed = 0
+chamber_temperature = 0
+complete_print_exhaust_fan_speed = 80
+cool_cds_fan_start_at_height = 0
+cool_special_cds_fan_speed = 0
+default_filament_colour = ""
+during_print_exhaust_fan_speed = 60
+enable_overhang_bridge_fan = 1
+enable_pressure_advance = 0
+enable_special_area_additional_cooling_fan = 0
+epoxy_resin_plate_temp = 0
+epoxy_resin_plate_temp_initial_layer = 0
+filament_cooling_final_speed = 3.4
+filament_cooling_initial_speed = 2.2
+filament_cooling_moves = 4
+filament_is_support = 0
+filament_load_time = 0
+filament_loading_speed = 28
+filament_loading_speed_start = 3
+filament_multitool_ramming = 0
+filament_multitool_ramming_flow = 10
+filament_multitool_ramming_volume = 10
+filament_notes = ""
+filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
+filament_retract_lift_above = 0
+filament_retract_lift_below = 0
+filament_retract_lift_enforce = All Surfaces
+filament_shrink = 100%
+filament_toolchange_delay = 0
+filament_unload_time = 0
+filament_unloading_speed = 90
+filament_unloading_speed_start = 100
+material_flow_dependent_temperature = 0
+material_flow_temp_graph = [[3.5,200],[7.0,240]]
+nozzle_temperature_range_high = 270
+nozzle_temperature_range_low = 220
+pressure_advance = 0.02
+required_nozzle_HRC = 0
+support_material_interface_fan_speed = -1

print_config/prusa_slicer/materials/Generic_TPU.ini

@@ -0,0 +1,94 @@
+[metadata]
+show_name = Generic TPU
+material_type = tpu
+
+
+[settings]
+cool_plate_temp = 30
+eng_plate_temp = 30
+hot_plate_temp = 30
+textured_plate_temp = 30
+cool_plate_temp_initial_layer = 30
+eng_plate_temp_initial_layer = 30
+hot_plate_temp_initial_layer = 30
+textured_plate_temp_initial_layer = 30
+overhang_fan_threshold = 95%
+overhang_fan_speed = 100
+slow_down_for_layer_cooling = 1
+close_fan_the_first_x_layers = 1
+filament_end_gcode = ;filament end gcode \n
+filament_flow_ratio = 1
+reduce_fan_stop_start_freq = 1
+fan_cooling_layer_time = 100
+filament_cost = 20
+filament_density = 1.24
+filament_deretraction_speed = nil
+filament_diameter = 1.75
+filament_max_volumetric_speed = 3
+filament_minimal_purge_on_wipe_tower = 15
+filament_retraction_minimum_travel = nil
+filament_retract_before_wipe = nil
+filament_retract_when_changing_layer = nil
+filament_retraction_length = 2
+filament_z_hop = 0.2
+filament_z_hop_types = nil
+filament_retract_restart_extra = 0
+filament_retraction_speed = nil
+filament_settings_id = 
+filament_soluble = 0
+filament_type = TPU
+filament_vendor = Generic
+filament_wipe = nil
+filament_wipe_distance = nil
+bed_type = Cool Plate
+nozzle_temperature_initial_layer = 200
+full_fan_speed_layer = 0
+fan_max_speed = 100
+fan_min_speed = 100
+slow_down_min_speed = 10
+slow_down_layer_time = 12
+filament_start_gcode = ;filament start gcode\n
+nozzle_temperature = 200
+temperature_vitrification = 60
+filament_adhesiveness_category = 600
+additional_cooling_fan_speed = 0
+nozzle_temperature_range_low = 200
+nozzle_temperature_range_high = 250
+activate_air_filtration = 0
+activate_chamber_temp_control = 0
+chamber_temperature = 0
+complete_print_exhaust_fan_speed = 80
+cool_cds_fan_start_at_height = 0
+cool_special_cds_fan_speed = 0
+default_filament_colour = ""
+during_print_exhaust_fan_speed = 60
+enable_overhang_bridge_fan = 1
+enable_pressure_advance = 0
+enable_special_area_additional_cooling_fan = 0
+epoxy_resin_plate_temp = 0
+epoxy_resin_plate_temp_initial_layer = 0
+filament_cooling_final_speed = 3.4
+filament_cooling_initial_speed = 2.2
+filament_cooling_moves = 4
+filament_is_support = 0
+filament_load_time = 0
+filament_loading_speed = 28
+filament_loading_speed_start = 3
+filament_multitool_ramming = 0
+filament_multitool_ramming_flow = 10
+filament_multitool_ramming_volume = 10
+filament_notes = ""
+filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
+filament_retract_lift_above = 0
+filament_retract_lift_below = 0
+filament_retract_lift_enforce = All Surfaces
+filament_shrink = 100%
+filament_toolchange_delay = 0
+filament_unload_time = 0
+filament_unloading_speed = 90
+filament_unloading_speed_start = 100
+material_flow_dependent_temperature = 0
+material_flow_temp_graph = [[3.5,200],[7.0,240]]
+pressure_advance = 0.02
+required_nozzle_HRC = 0
+support_material_interface_fan_speed = -1

print_config/prusa_slicer/materials/Hyper_L-W_PLA.ini

@@ -0,0 +1,96 @@
+[metadata]
+show_name = Hyper L-W PLA
+material_type = pla
+
+
+[settings]
+cool_plate_temp = 50
+eng_plate_temp = 45
+hot_plate_temp = 60
+textured_plate_temp = 60
+cool_plate_temp_initial_layer = 50
+eng_plate_temp_initial_layer = 45
+hot_plate_temp_initial_layer = 60
+textured_plate_temp_initial_layer = 60
+overhang_fan_threshold = 50%
+overhang_fan_speed = 100
+slow_down_for_layer_cooling = 1
+close_fan_the_first_x_layers = 1
+filament_end_gcode = ;filament end gcode 
+filament_flow_ratio = 0.75
+reduce_fan_stop_start_freq = 1
+fan_cooling_layer_time = 100
+filament_cost = 48.9
+filament_density = 1.21
+filament_deretraction_speed = 15
+filament_diameter = 1.75
+filament_max_volumetric_speed = 4
+filament_minimal_purge_on_wipe_tower = 15
+filament_retraction_minimum_travel = 3
+filament_retract_before_wipe = nil
+filament_retract_when_changing_layer = nil
+filament_retraction_length = 0.6
+filament_z_hop = nil
+filament_z_hop_types = nil
+filament_retract_restart_extra = nil
+filament_retraction_speed = 15
+filament_settings_id = 
+filament_soluble = 0
+filament_type = PLA
+filament_vendor = Creality
+filament_wipe = nil
+filament_wipe_distance = nil
+bed_type = Cool Plate
+nozzle_temperature_initial_layer = 220
+full_fan_speed_layer = 0
+fan_max_speed = 100
+fan_min_speed = 60
+slow_down_min_speed = 10
+slow_down_layer_time = 10
+filament_start_gcode = ;filament start gcode
+nozzle_temperature = 220
+temperature_vitrification = 60
+filament_adhesiveness_category = 100
+nozzle_temperature_range_low = 200
+nozzle_temperature_range_high = 270
+additional_cooling_fan_speed = 0
+activate_air_filtration = 0
+activate_chamber_temp_control = 0
+chamber_temperature = 0
+complete_print_exhaust_fan_speed = 80
+cool_cds_fan_start_at_height = 0.5
+cool_special_cds_fan_speed = 0
+customized_plate_temp = 60
+customized_plate_temp_initial_layer = 60
+default_filament_colour = ""
+during_print_exhaust_fan_speed = 60
+enable_overhang_bridge_fan = 1
+enable_pressure_advance = 1
+enable_special_area_additional_cooling_fan = 0
+epoxy_resin_plate_temp = 60
+epoxy_resin_plate_temp_initial_layer = 60
+filament_cooling_final_speed = 3.4
+filament_cooling_initial_speed = 2.2
+filament_cooling_moves = 4
+filament_is_support = 0
+filament_load_time = 0
+filament_loading_speed = 28
+filament_loading_speed_start = 3
+filament_multitool_ramming = 0
+filament_multitool_ramming_flow = 10
+filament_multitool_ramming_volume = 10
+filament_notes = ""
+filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
+filament_retract_lift_above = nil
+filament_retract_lift_below = nil
+filament_retract_lift_enforce = nil
+filament_shrink = 100%
+filament_shrinkage_compensation_z = 100%
+filament_toolchange_delay = 0
+filament_unload_time = 0
+filament_unloading_speed = 90
+filament_unloading_speed_start = 100
+material_flow_dependent_temperature = 0
+pressure_advance = 0.1
+required_nozzle_HRC = 0
+support_material_interface_fan_speed = -1

print_config/prusa_slicer/materials/Hyper_Marble_PLA.ini

@@ -0,0 +1,97 @@
+[metadata]
+show_name = Hyper Marble PLA
+material_type = pla
+
+
+[settings]
+cool_plate_temp = 50
+eng_plate_temp = 45
+hot_plate_temp = 50
+textured_plate_temp = 50
+cool_plate_temp_initial_layer = 50
+eng_plate_temp_initial_layer = 45
+hot_plate_temp_initial_layer = 50
+textured_plate_temp_initial_layer = 50
+overhang_fan_threshold = 50%
+overhang_fan_speed = 100
+slow_down_for_layer_cooling = 1
+close_fan_the_first_x_layers = 1
+filament_end_gcode = ;filament end gcode 
+filament_flow_ratio = 0.95
+reduce_fan_stop_start_freq = 1
+fan_cooling_layer_time = 100
+filament_cost = 23.9
+filament_density = 1.25
+filament_deretraction_speed = 15
+filament_diameter = 1.75
+filament_max_volumetric_speed = 18
+filament_minimal_purge_on_wipe_tower = 15
+filament_retraction_minimum_travel = 2
+filament_retract_before_wipe = nil
+filament_retract_when_changing_layer = nil
+filament_retraction_length = 1.5
+filament_z_hop = nil
+filament_z_hop_types = nil
+filament_retract_restart_extra = nil
+filament_retraction_speed = 15
+filament_settings_id = 
+filament_soluble = 0
+filament_type = PLA
+filament_vendor = Creality
+filament_wipe = nil
+filament_wipe_distance = 3
+bed_type = Cool Plate
+nozzle_temperature_initial_layer = 220
+full_fan_speed_layer = 0
+fan_max_speed = 100
+fan_min_speed = 100
+slow_down_min_speed = 20
+slow_down_layer_time = 14
+filament_start_gcode = ;filament start gcode
+nozzle_temperature = 220
+temperature_vitrification = 60
+filament_adhesiveness_category = 100
+nozzle_temperature_range_low = 190
+nozzle_temperature_range_high = 240
+additional_cooling_fan_speed = 0
+activate_air_filtration = 0
+activate_chamber_temp_control = 0
+chamber_temperature = 0
+complete_print_exhaust_fan_speed = 80
+cool_cds_fan_start_at_height = 0
+cool_special_cds_fan_speed = 0
+customized_plate_temp = 50
+customized_plate_temp_initial_layer = 50
+default_filament_colour = ""
+during_print_exhaust_fan_speed = 60
+enable_overhang_bridge_fan = 1
+enable_pressure_advance = 1
+enable_special_area_additional_cooling_fan = 0
+epoxy_resin_plate_temp = 50
+epoxy_resin_plate_temp_initial_layer = 50
+filament_cooling_final_speed = 3.4
+filament_cooling_initial_speed = 2.2
+filament_cooling_moves = 4
+filament_is_support = 0
+filament_load_time = 0
+filament_loading_speed = 28
+filament_loading_speed_start = 3
+filament_multitool_ramming = 0
+filament_multitool_ramming_flow = 10
+filament_multitool_ramming_volume = 10
+filament_notes = ""
+filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
+filament_retract_lift_above = nil
+filament_retract_lift_below = nil
+filament_retract_lift_enforce = nil
+filament_shrink = 100%
+filament_shrinkage_compensation_z = 100%
+filament_toolchange_delay = 0
+filament_unload_time = 0
+filament_unloading_speed = 90
+filament_unloading_speed_start = 100
+material_flow_dependent_temperature = 0
+material_flow_temp_graph = [[0.8,200],[1.0,200],[1.2,220]]
+pressure_advance = 0.04
+required_nozzle_HRC = 0
+support_material_interface_fan_speed = -1

print_config/prusa_slicer/materials/Hyper_PETG.ini

@@ -0,0 +1,94 @@
+[metadata]
+show_name = Hyper PETG
+material_type = petg
+
+
+[settings]
+filament_adhesiveness_category = 300
+cool_plate_temp = 60
+eng_plate_temp = 0
+hot_plate_temp = 70
+textured_plate_temp = 70
+cool_plate_temp_initial_layer = 60
+eng_plate_temp_initial_layer = 0
+hot_plate_temp_initial_layer = 70
+textured_plate_temp_initial_layer = 70
+overhang_fan_threshold = 25%
+overhang_fan_speed = 90
+slow_down_for_layer_cooling = 1
+close_fan_the_first_x_layers = 3
+filament_end_gcode = ;filament end gcode \n
+filament_flow_ratio = 1.0
+reduce_fan_stop_start_freq = 1
+fan_cooling_layer_time = 30
+filament_cost = 69
+filament_density = 1.27
+filament_deretraction_speed = nil
+filament_diameter = 1.75
+filament_max_volumetric_speed = 10
+filament_minimal_purge_on_wipe_tower = 15
+filament_retraction_minimum_travel = nil
+filament_retract_before_wipe = nil
+filament_retract_when_changing_layer = nil
+filament_retraction_length = 1.2
+filament_z_hop = 0.2
+filament_z_hop_types = nil
+filament_retract_restart_extra = 0
+filament_retraction_speed = nil
+filament_settings_id = 
+filament_soluble = 0
+filament_type = PETG
+filament_vendor = Creality
+filament_wipe = nil
+filament_wipe_distance = 2
+bed_type = Cool Plate
+nozzle_temperature_initial_layer = 235
+full_fan_speed_layer = 0
+fan_max_speed = 80
+fan_min_speed = 40
+slow_down_min_speed = 10
+slow_down_layer_time = 8
+filament_start_gcode = ;filament start gcode\n
+nozzle_temperature = 240
+temperature_vitrification = 80
+activate_air_filtration = 0
+activate_chamber_temp_control = 0
+additional_cooling_fan_speed = 0
+chamber_temperature = 0
+complete_print_exhaust_fan_speed = 80
+cool_cds_fan_start_at_height = 0
+cool_special_cds_fan_speed = 0
+default_filament_colour = ""
+during_print_exhaust_fan_speed = 60
+enable_overhang_bridge_fan = 1
+enable_pressure_advance = 1
+enable_special_area_additional_cooling_fan = 0
+epoxy_resin_plate_temp = 0
+epoxy_resin_plate_temp_initial_layer = 0
+filament_cooling_final_speed = 3.4
+filament_cooling_initial_speed = 2.2
+filament_cooling_moves = 4
+filament_is_support = 0
+filament_load_time = 0
+filament_loading_speed = 28
+filament_loading_speed_start = 3
+filament_multitool_ramming = 0
+filament_multitool_ramming_flow = 10
+filament_multitool_ramming_volume = 10
+filament_notes = ""
+filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
+filament_retract_lift_above = 0
+filament_retract_lift_below = 0
+filament_retract_lift_enforce = All Surfaces
+filament_shrink = 100%
+filament_toolchange_delay = 0
+filament_unload_time = 0
+filament_unloading_speed = 90
+filament_unloading_speed_start = 100
+material_flow_dependent_temperature = 1
+material_flow_temp_graph = [[3.0,230],[10.0,240],[20.0,250]]
+nozzle_temperature_range_high = 270
+nozzle_temperature_range_low = 220
+pressure_advance = 0.07
+required_nozzle_HRC = 0
+support_material_interface_fan_speed = -1

print_config/prusa_slicer/materials/Hyper_PLA.ini

@@ -0,0 +1,94 @@
+[metadata]
+show_name = Hyper PLA
+material_type = pla
+
+
+[settings]
+cool_plate_temp = 50
+eng_plate_temp = 45
+hot_plate_temp = 50
+textured_plate_temp = 50
+cool_plate_temp_initial_layer = 50
+eng_plate_temp_initial_layer = 45
+hot_plate_temp_initial_layer = 50
+textured_plate_temp_initial_layer = 50
+overhang_fan_threshold = 50%
+overhang_fan_speed = 100
+slow_down_for_layer_cooling = 1
+close_fan_the_first_x_layers = 1
+filament_end_gcode = ;filament end gcode 
+filament_flow_ratio = 0.95
+reduce_fan_stop_start_freq = 1
+fan_cooling_layer_time = 100
+filament_cost = 30
+filament_density = 1.24
+filament_deretraction_speed = nil
+filament_diameter = 1.75
+filament_max_volumetric_speed = 23
+filament_minimal_purge_on_wipe_tower = 15
+filament_retraction_minimum_travel = nil
+filament_retract_before_wipe = nil
+filament_retract_when_changing_layer = nil
+filament_retraction_length = 1.2
+filament_z_hop = 0.2
+filament_z_hop_types = Slope Lift
+filament_retract_restart_extra = 0
+filament_retraction_speed = 40
+filament_settings_id = 
+filament_soluble = 0
+filament_type = PLA
+filament_vendor = Creality
+filament_wipe = nil
+filament_wipe_distance = nil
+bed_type = Cool Plate
+nozzle_temperature_initial_layer = 190
+full_fan_speed_layer = 0
+fan_max_speed = 100
+fan_min_speed = 100
+slow_down_min_speed = 20
+slow_down_layer_time = 6
+filament_start_gcode = ;filament start gcode
+nozzle_temperature = 190
+temperature_vitrification = 100
+filament_adhesiveness_category = 100
+nozzle_temperature_range_low = 190
+nozzle_temperature_range_high = 240
+additional_cooling_fan_speed = 0
+activate_air_filtration = 0
+activate_chamber_temp_control = 0
+chamber_temperature = 0
+complete_print_exhaust_fan_speed = 80
+cool_cds_fan_start_at_height = 0
+cool_special_cds_fan_speed = 0
+default_filament_colour = ""
+during_print_exhaust_fan_speed = 60
+enable_overhang_bridge_fan = 1
+enable_pressure_advance = 0
+enable_special_area_additional_cooling_fan = 0
+epoxy_resin_plate_temp = 0
+epoxy_resin_plate_temp_initial_layer = 0
+filament_cooling_final_speed = 3.4
+filament_cooling_initial_speed = 2.2
+filament_cooling_moves = 4
+filament_is_support = 0
+filament_load_time = 0
+filament_loading_speed = 28
+filament_loading_speed_start = 3
+filament_multitool_ramming = 0
+filament_multitool_ramming_flow = 10
+filament_multitool_ramming_volume = 10
+filament_notes = ""
+filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
+filament_retract_lift_above = 0
+filament_retract_lift_below = 0
+filament_retract_lift_enforce = All Surfaces
+filament_shrink = 100%
+filament_toolchange_delay = 0
+filament_unload_time = 0
+filament_unloading_speed = 90
+filament_unloading_speed_start = 100
+material_flow_dependent_temperature = 0
+material_flow_temp_graph = [[3.5,200],[7.0,240]]
+pressure_advance = 0.02
+required_nozzle_HRC = 0
+support_material_interface_fan_speed = -1

print_config/prusa_slicer/materials/Hyper_Stardust_PLA.ini

@@ -0,0 +1,97 @@
+[metadata]
+show_name = Hyper Stardust PLA
+material_type = pla
+
+
+[settings]
+cool_plate_temp = 50
+eng_plate_temp = 45
+hot_plate_temp = 50
+textured_plate_temp = 50
+cool_plate_temp_initial_layer = 50
+eng_plate_temp_initial_layer = 45
+hot_plate_temp_initial_layer = 50
+textured_plate_temp_initial_layer = 50
+overhang_fan_threshold = 50%
+overhang_fan_speed = 100
+slow_down_for_layer_cooling = 1
+close_fan_the_first_x_layers = 1
+filament_end_gcode = ;filament end gcode 
+filament_flow_ratio = 0.95
+reduce_fan_stop_start_freq = 1
+fan_cooling_layer_time = 100
+filament_cost = 26.9
+filament_density = 1.24
+filament_deretraction_speed = 15
+filament_diameter = 1.75
+filament_max_volumetric_speed = 18
+filament_minimal_purge_on_wipe_tower = 15
+filament_retraction_minimum_travel = 2
+filament_retract_before_wipe = nil
+filament_retract_when_changing_layer = nil
+filament_retraction_length = 2
+filament_z_hop = nil
+filament_z_hop_types = nil
+filament_retract_restart_extra = nil
+filament_retraction_speed = 15
+filament_settings_id = 
+filament_soluble = 0
+filament_type = PLA
+filament_vendor = Creality
+filament_wipe = nil
+filament_wipe_distance = 3
+bed_type = Cool Plate
+nozzle_temperature_initial_layer = 220
+full_fan_speed_layer = 0
+fan_max_speed = 100
+fan_min_speed = 100
+slow_down_min_speed = 10
+slow_down_layer_time = 14
+filament_start_gcode = ;filament start gcode
+nozzle_temperature = 220
+temperature_vitrification = 60
+filament_adhesiveness_category = 100
+nozzle_temperature_range_low = 190
+nozzle_temperature_range_high = 240
+additional_cooling_fan_speed = 0
+activate_air_filtration = 0
+activate_chamber_temp_control = 0
+chamber_temperature = 0
+complete_print_exhaust_fan_speed = 80
+cool_cds_fan_start_at_height = 0.5
+cool_special_cds_fan_speed = 0
+customized_plate_temp = 50
+customized_plate_temp_initial_layer = 50
+default_filament_colour = ""
+during_print_exhaust_fan_speed = 60
+enable_overhang_bridge_fan = 1
+enable_pressure_advance = 1
+enable_special_area_additional_cooling_fan = 0
+epoxy_resin_plate_temp = 50
+epoxy_resin_plate_temp_initial_layer = 50
+filament_cooling_final_speed = 3.4
+filament_cooling_initial_speed = 2.2
+filament_cooling_moves = 4
+filament_is_support = 0
+filament_load_time = 0
+filament_loading_speed = 28
+filament_loading_speed_start = 3
+filament_multitool_ramming = 0
+filament_multitool_ramming_flow = 10
+filament_multitool_ramming_volume = 10
+filament_notes = ""
+filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
+filament_retract_lift_above = nil
+filament_retract_lift_below = nil
+filament_retract_lift_enforce = nil
+filament_shrink = 100%
+filament_shrinkage_compensation_z = 100%
+filament_toolchange_delay = 0
+filament_unload_time = 0
+filament_unloading_speed = 90
+filament_unloading_speed_start = 100
+material_flow_dependent_temperature = 0
+material_flow_temp_graph = [[0.8,200],[1.0,200],[1.2,220]]
+pressure_advance = 0.04
+required_nozzle_HRC = 0
+support_material_interface_fan_speed = -1

print_config/prusa_slicer/materials/Soleyin_Ultra_PLA.ini

@@ -0,0 +1,97 @@
+[metadata]
+show_name = Soleyin Ultra PLA
+material_type = pla
+
+
+[settings]
+cool_plate_temp = 50
+eng_plate_temp = 45
+hot_plate_temp = 50
+textured_plate_temp = 50
+cool_plate_temp_initial_layer = 50
+eng_plate_temp_initial_layer = 45
+hot_plate_temp_initial_layer = 50
+textured_plate_temp_initial_layer = 50
+overhang_fan_threshold = 50%
+overhang_fan_speed = 100
+slow_down_for_layer_cooling = 1
+close_fan_the_first_x_layers = 1
+filament_end_gcode = ;filament end gcode 
+filament_flow_ratio = 0.96
+reduce_fan_stop_start_freq = 1
+fan_cooling_layer_time = 100
+filament_cost = 6
+filament_density = 1.25
+filament_deretraction_speed = 15
+filament_diameter = 1.75
+filament_max_volumetric_speed = 16
+filament_minimal_purge_on_wipe_tower = 15
+filament_retraction_minimum_travel = nil
+filament_retract_before_wipe = 90%
+filament_retract_when_changing_layer = nil
+filament_retraction_length = nil
+filament_z_hop = nil
+filament_z_hop_types = nil
+filament_retract_restart_extra = nil
+filament_retraction_speed = 15
+filament_settings_id = 
+filament_soluble = 0
+filament_type = PLA
+filament_vendor = Creality
+filament_wipe = nil
+filament_wipe_distance = nil
+bed_type = Cool Plate
+nozzle_temperature_initial_layer = 220
+full_fan_speed_layer = 0
+fan_max_speed = 100
+fan_min_speed = 100
+slow_down_min_speed = 20
+slow_down_layer_time = 12
+filament_start_gcode = ;filament start gcode
+nozzle_temperature = 220
+temperature_vitrification = 60
+filament_adhesiveness_category = 100
+nozzle_temperature_range_low = 190
+nozzle_temperature_range_high = 240
+additional_cooling_fan_speed = 0
+activate_air_filtration = 0
+activate_chamber_temp_control = 0
+chamber_temperature = 0
+complete_print_exhaust_fan_speed = 80
+cool_cds_fan_start_at_height = 0
+cool_special_cds_fan_speed = 0
+customized_plate_temp = 60
+customized_plate_temp_initial_layer = 60
+default_filament_colour = ""
+during_print_exhaust_fan_speed = 60
+enable_overhang_bridge_fan = 1
+enable_pressure_advance = 1
+enable_special_area_additional_cooling_fan = 0
+epoxy_resin_plate_temp = 60
+epoxy_resin_plate_temp_initial_layer = 60
+filament_cooling_final_speed = 3.4
+filament_cooling_initial_speed = 2.2
+filament_cooling_moves = 4
+filament_is_support = 0
+filament_load_time = 0
+filament_loading_speed = 28
+filament_loading_speed_start = 3
+filament_multitool_ramming = 0
+filament_multitool_ramming_flow = 10
+filament_multitool_ramming_volume = 10
+filament_notes = ""
+filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
+filament_retract_lift_above = nil
+filament_retract_lift_below = nil
+filament_retract_lift_enforce = nil
+filament_shrink = 100%
+filament_shrinkage_compensation_z = 100%
+filament_toolchange_delay = 0
+filament_unload_time = 0
+filament_unloading_speed = 90
+filament_unloading_speed_start = 100
+material_flow_dependent_temperature = 0
+material_flow_temp_graph = [[1.0,200],[1.1,200],[1.2,220]]
+pressure_advance = 0.05
+required_nozzle_HRC = 0
+support_material_interface_fan_speed = -1

print_config/prusa_slicer/printers/Ender3_V3_SE.ini

@@ -0,0 +1,104 @@
+[metadata]
+show_name = Ender3 V3 SE Model
+
+
+[settings]
+family = Creality
+printer_technology = FFF
+deretraction_speed = 30
+extruder_colour = #FCE94F
+extruder_offset = 0x0
+gcode_flavor = marlin2
+silent_mode = 0
+support_chamber_temp_control = 0
+support_air_filtration = 0
+machine_max_acceleration_e = 5000,5000
+machine_max_acceleration_extruding = 5000,5000
+machine_max_acceleration_retracting = 2500,2500
+machine_max_acceleration_x = 5000,5000
+machine_max_acceleration_y = 5000,5000
+machine_max_acceleration_z = 500,500
+machine_max_speed_e = 100,100
+machine_max_speed_x = 500,500
+machine_max_speed_y = 500,500
+machine_max_speed_z = 30,30
+machine_max_jerk_e = 5,5
+machine_max_jerk_x = 10,10
+machine_max_jerk_y = 10,10
+machine_max_jerk_z = 0.4,0.4
+machine_min_extruding_rate = 0,0
+machine_min_travel_rate = 0,0
+max_layer_height = 0.36
+min_layer_height = 0.08
+printable_height = 250
+extruder_clearance_radius = 90
+extruder_clearance_height_to_rod = 47
+extruder_clearance_height_to_lid = 34
+nozzle_diameter = 0.4
+printer_settings_id = 
+printer_variant = 0.4
+retraction_minimum_travel = 1
+retract_before_wipe = 100
+retract_when_changing_layer = 1
+retraction_length = 0.8
+retract_length_toolchange = 1
+z_hop = 0.4
+retract_restart_extra = 0
+retract_restart_extra_toolchange = 0
+retraction_speed = 30
+single_extruder_multi_material = 1
+change_filament_gcode = 
+wipe = 1
+z_hop_types = Slope Lift
+before_layer_change_gcode = ;BEFORE_LAYER_CHANGE\n;[layer_z]\nG92 E0\n
+default_print_profile = 0.20mm Standard @Creality Ender-3 V3 SE 0.4 nozzle
+machine_start_gcode = M220 S100 ;Reset Feedrate \nM221 S100 ;Reset Flowrate \n \nM140 S[bed_temperature_initial_layer_single] ;Set final bed temp \nG28 ;Home \n \nG92 E0 ;Reset Extruder \nG1 Z2.0 F3000 ;Move Z Axis up \nM104 S[nozzle_temperature_initial_layer] ;Set final nozzle temp \nG1 X-2.1 Y20 Z0.28 F5000.0 ;Move to start position \nM190 S[bed_temperature_initial_layer_single] ;Wait for bed temp to stabilize \nM109 S[nozzle_temperature_initial_layer] ;Wait for nozzle temp to stabilize \nG1 X-2.1 Y145.0 Z0.28 F1500.0 E15 ;Draw the first line \nG1 X-2.4 Y145.0 Z0.28 F5000.0 ;Move to side a little \nG1 X-2.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line \nG92 E0  ;Reset Extruder \nG1 E-1.0000 F1800 ;Retract a bit \nG1 Z2.0 F3000 ;Move Z Axis up \nG1 E0.0000 F1800
+machine_end_gcode = G91 ;Relative positionning \nG1 E-2 F2700 ;Retract a bit \nG1 E-2 Z0.2 F2400 ;Retract and raise Z \nG1 X5 Y5 F3000 ;Wipe out \nG1 Z10 ;Raise Z more \nG90 ;Absolute positionning \n \nG1 X0 Y220 ;Present print \nM106 S0 ;Turn-off fan \nM104 S0 ;Turn-off hotend \nM140 S0 ;Turn-off bed \n \nM84 X Y E ;Disable all steppers but Z
+machine_max_acceleration_travel = 5000,5000
+machine_pause_gcode = M25
+bed_exclude_area = 0x0
+layer_change_gcode = 
+scan_first_layer = 0
+nozzle_type = brass
+auxiliary_fan = 0
+printer_model = Creality Ender-3 V3 SE
+printer_structure = i3
+bbl_use_printhost = 0
+bed_mesh_max = 99999,99999
+bed_mesh_min = -99999,-99999
+bed_mesh_probe_distance = 50,50
+best_object_pos = 0.5,0.5
+cooling_tube_length = 5
+cooling_tube_retraction = 91.5
+creality_flush_time = 86.0
+disable_m73 = 0
+emit_machine_limits_to_gcode = 1
+enable_filament_ramming = 1
+extra_loading_move = -2
+fan_kickstart = 0
+fan_speedup_overhangs = 1
+fan_speedup_time = 0
+high_current_on_filament_swap = 0
+machine_LED_light_exist = 0
+machine_load_filament_time = 11
+machine_platform_motion_enable = 0
+machine_unload_filament_time = 0
+manual_filament_change = 1
+nozzle_hrc = 0
+nozzle_volume = 0
+parking_pos_retraction = 92
+preferred_orientation = 0
+printable_area = 0x0,220x0,220x220,0x220
+purge_in_prime_tower = 1
+support_multi_bed_types = 1
+time_cost = 0
+use_firmware_retraction = 0
+use_relative_e_distances = 1
+z_offset = 0
+retract_lift_above = 0
+retract_lift_below = 0
+retract_lift_enforce = All Surfaces
+wipe_distance = 2
+
+
+

print_config/prusa_slicer/quality/0.08mm_Extra_Fine.ini

@@ -0,0 +1,216 @@
+[metadata]
+show_name = 0.08mm Extra Fine Quality
+
+
+[settings]
+adaptive_layer_height = 0
+reduce_crossing_wall = 0
+bridge_flow = 0.8
+bridge_speed = 25
+brim_width = 5
+print_sequence = by layer
+default_acceleration = 2500
+bridge_no_support = 0
+elefant_foot_compensation = 0.15
+outer_wall_line_width = 0.42
+outer_wall_speed = 60
+line_width = 0.46
+infill_direction = 45
+sparse_infill_density = 10%
+sparse_infill_pattern = zig-zag
+initial_layer_line_width = 0.46
+initial_layer_print_height = 0.2
+initial_layer_speed = 60
+gap_infill_speed = 50
+infill_combination = 0
+sparse_infill_line_width = 0.45
+infill_wall_overlap = 15%
+sparse_infill_speed = 180
+interface_shells = 0
+detect_overhang_wall = 1
+reduce_infill_retraction = 1
+wall_loops = 2
+inner_wall_line_width = 0.45
+inner_wall_speed = 90
+print_settings_id = 
+raft_layers = 0
+seam_position = aligned
+skirt_distance = 2
+skirt_height = 2
+minimum_sparse_infill_area = 10
+internal_solid_infill_line_width = 0.42
+internal_solid_infill_speed = 180
+spiral_mode = 0
+standby_temperature_delta = -5
+detect_thin_wall = 1
+top_surface_line_width = 0.42
+top_surface_speed = 50
+travel_speed = 150
+enable_prime_tower = 0
+prime_tower_width = 60
+xy_hole_compensation = 0
+xy_contour_compensation = 0
+max_travel_detour_distance = 0
+bottom_surface_pattern = monotonic
+bottom_shell_layers = 7
+bottom_shell_thickness = 0
+brim_object_gap = 0.1
+compatible_printers_condition = 
+top_surface_acceleration = 2500
+draft_shield = disabled
+enable_arc_fitting = 0
+wall_infill_order = inner wall/outer wall/infill
+initial_layer_acceleration = 500
+travel_acceleration = 2500
+inner_wall_acceleration = 2000
+ironing_flow = 15%
+ironing_spacing = 0.1
+ironing_speed = 20
+ironing_type = no ironing
+layer_height = 0.08
+overhang_1_4_speed = 0
+overhang_2_4_speed = 20
+overhang_3_4_speed = 15
+overhang_4_4_speed = 10
+skirt_loops = 0
+resolution = 0.012
+top_surface_pattern = monotonicline
+top_shell_layers = 9
+top_shell_thickness = 0.8
+initial_layer_infill_speed = 80
+wipe_tower_no_sparse_layers = 0
+accel_to_decel_enable = 1
+accel_to_decel_factor = 50%
+acceleration_limit_mess = [[0.5,1.0,100,6000],[1.0,1.5,80,5500],[1.5,2.0,60,5000]]
+acceleration_limit_mess_enable = 0
+alternate_extra_wall = 0
+bottom_solid_infill_flow_ratio = 1
+bridge_acceleration = 50%
+bridge_angle = 0
+bridge_density = 100%
+brim_ears_detection_length = 1
+brim_ears_max_angle = 125
+brim_type = no_brim
+default_jerk = 8
+detect_narrow_internal_solid_infill = 1
+elefant_foot_compensation_layers = 1
+enable_overhang_speed = 1
+enforce_support_layers = 0
+ensure_vertical_shell_thickness = ensure_all
+exclude_object = 0
+extra_perimeters_on_overhangs = 0
+filter_out_gap_fill = 0
+flush_into_infill = 0
+flush_into_objects = 0
+flush_into_support = 1
+fuzzy_skin = none
+fuzzy_skin_first_layer = 0
+fuzzy_skin_point_distance = 0.8
+fuzzy_skin_thickness = 0.3
+gcode_add_line_number = 0
+gcode_comments = 0
+gcode_label_objects = 1
+hole_to_polyhole = 0
+hole_to_polyhole_threshold = 0.01
+hole_to_polyhole_twisted = 1
+independent_support_layer_height = 1
+infill_anchor = 400%
+infill_anchor_max = 20
+infill_jerk = 20
+initial_layer_jerk = 8
+initial_layer_min_bead_width = 85%
+initial_layer_travel_speed = 100%
+inner_wall_jerk = 20
+internal_bridge_flow = 1
+internal_bridge_speed = 150%
+internal_solid_infill_acceleration = 100%
+internal_solid_infill_pattern = monotonic
+ironing_angle = -1
+ironing_pattern = zig-zag
+ironing_support_layer = 0
+is_infill_first = 0
+make_overhang_printable = 0
+make_overhang_printable_angle = 55
+make_overhang_printable_hole_size = 0
+max_bridge_length = 10
+max_volumetric_extrusion_rate_slope = 0
+max_volumetric_extrusion_rate_slope_segment_length = 3
+min_bead_width = 85%
+min_feature_size = 25%
+min_width_top_surface = 300%
+minimum_support_area = 5
+mmu_segmented_region_interlocking_depth = 0
+mmu_segmented_region_max_width = 0
+only_one_wall_first_layer = 0
+only_one_wall_top = 0
+ooze_prevention = 0
+outer_wall_acceleration = 1000
+outer_wall_jerk = 20
+overhang_reverse = 0
+overhang_reverse_internal_only = 0
+overhang_reverse_threshold = 50%
+overhang_speed_classic = 0
+precise_outer_wall = 0
+prime_tower_brim_width = 3
+prime_tower_enhance_type = chamfer
+prime_volume = 45
+print_flow_ratio = 1
+print_order = default
+raft_contact_distance = 0.1
+raft_expansion = 1.5
+raft_first_layer_density = 90%
+raft_first_layer_expansion = 2
+role_based_wipe_speed = 1
+scarf_angle_threshold = 155
+scarf_joint_flow_ratio = 1
+scarf_joint_speed = 100%
+scarf_overhang_threshold = 40%
+seam_gap = 10%
+seam_slope_conditional = 0
+seam_slope_entire_loop = 0
+seam_slope_inner_walls = 0
+seam_slope_min_length = 20
+seam_slope_start_height = 0
+seam_slope_steps = 10
+seam_slope_type = none
+single_extruder_multi_material_priming = 0
+skirt_speed = 50
+slice_closing_radius = 0.049
+slicing_mode = regular
+slow_down_layers = 0
+slowdown_for_curled_perimeters = 0
+small_area_infill_flow_compensation = 0
+small_area_infill_flow_compensation_model = 0,0;\n0.2,0.4444;\n0.4,0.6145;\n0.6,0.7059;\n0.8,0.7619;\n1.5,0.8571;\n2,0.8889;\n3,0.9231;\n5,0.9520;\n10,1
+small_perimeter_speed = 50%
+small_perimeter_threshold = 0
+solid_infill_filament = 1
+sparse_infill_acceleration = 100%
+sparse_infill_filament = 1
+speed_limit_to_height = [[100,150,200,6000],[150,200,200,4000],[200,250,200,2000]]
+speed_limit_to_height_enable = 0
+spiral_mode_max_xy_smoothing = 200%
+spiral_mode_smooth = 0
+staggered_inner_seams = 1
+thick_bridges = 0
+thick_internal_bridges = 1
+timelapse_type = 0
+top_solid_infill_flow_ratio = 1
+top_surface_jerk = 9
+travel_jerk = 12
+travel_speed_z = 0
+wall_direction = auto
+wall_distribution_count = 1
+wall_filament = 1
+wall_generator = arachne
+wall_sequence = inner wall/outer wall
+wall_transition_angle = 10
+wall_transition_filter_deviation = 25%
+wall_transition_length = 100%
+wipe_before_external_loop = 0
+wipe_on_loops = 0
+wipe_speed = 80%
+wipe_tower_bridging = 10
+wipe_tower_cone_angle = 0
+wipe_tower_extra_spacing = 100%
+wipe_tower_rotation_angle = 0
+wiping_volumes_extruders = 70,70,70,70,70,70,70,70,70,70

print_config/prusa_slicer/quality/0.12mm_Fine.ini

@@ -0,0 +1,200 @@
+[metadata]
+show_name = 0.12mm Fine Quality
+
+
+[settings]
+adaptive_layer_height = 0
+reduce_crossing_wall = 0
+bridge_flow = 0.95
+bridge_speed = 100
+brim_width = 5
+print_sequence = by layer
+default_acceleration = 2500
+bridge_no_support = 0
+elefant_foot_compensation = 0
+outer_wall_line_width = 0.42
+outer_wall_speed = 60
+line_width = 0.46
+infill_direction = 45
+sparse_infill_density = 15%
+sparse_infill_pattern = grid
+initial_layer_line_width = 0.46
+initial_layer_print_height = 0.2
+initial_layer_speed = 30
+gap_infill_speed = 50
+infill_combination = 0
+sparse_infill_line_width = 0.45
+infill_wall_overlap = 15%
+sparse_infill_speed = 180
+interface_shells = 0
+detect_overhang_wall = 1
+reduce_infill_retraction = 1
+wall_loops = 2
+inner_wall_line_width = 0.45
+inner_wall_speed = 90
+print_settings_id = 
+raft_layers = 0
+seam_position = aligned
+skirt_distance = 2
+skirt_height = 2
+minimum_sparse_infill_area = 10
+internal_solid_infill_line_width = 0.42
+internal_solid_infill_speed = 180
+spiral_mode = 0
+standby_temperature_delta = -5
+detect_thin_wall = 1
+top_surface_line_width = 0.42
+top_surface_speed = 50
+travel_speed = 150
+enable_prime_tower = 0
+prime_tower_width = 60
+xy_hole_compensation = 0
+xy_contour_compensation = 0
+max_travel_detour_distance = 0
+bottom_surface_pattern = monotonic
+bottom_shell_layers = 5
+bottom_shell_thickness = 0
+brim_object_gap = 0.1
+compatible_printers_condition = 
+top_surface_acceleration = 2500
+draft_shield = disabled
+enable_arc_fitting = 0
+wall_infill_order = inner wall/outer wall/infill
+initial_layer_acceleration = 500
+travel_acceleration = 2500
+inner_wall_acceleration = 2000
+ironing_flow = 15%
+ironing_spacing = 0.1
+ironing_speed = 20
+ironing_type = no ironing
+layer_height = 0.12
+overhang_1_4_speed = 0
+overhang_2_4_speed = 20
+overhang_3_4_speed = 15
+overhang_4_4_speed = 10
+skirt_loops = 0
+resolution = 0.012
+top_surface_pattern = monotonic
+top_shell_layers = 5
+top_shell_thickness = 0.8
+initial_layer_infill_speed = 80
+wipe_tower_no_sparse_layers = 0
+accel_to_decel_enable = 1
+accel_to_decel_factor = 50%
+acceleration_limit_mess = [[0.5,1.0,100,6000],[1.0,1.5,80,5500],[1.5,2.0,60,5000]]
+acceleration_limit_mess_enable = 0
+alternate_extra_wall = 0
+bottom_solid_infill_flow_ratio = 1
+bridge_acceleration = 50%
+bridge_angle = 0
+bridge_density = 100%
+brim_ears_detection_length = 1
+brim_ears_max_angle = 125
+brim_type = no_brim
+default_jerk = 8
+detect_narrow_internal_solid_infill = 1
+elefant_foot_compensation_layers = 1
+enable_overhang_speed = 1
+enforce_support_layers = 0
+ensure_vertical_shell_thickness = ensure_all
+exclude_object = 0
+extra_perimeters_on_overhangs = 0
+filter_out_gap_fill = 0
+flush_into_infill = 0
+flush_into_objects = 0
+flush_into_support = 1
+fuzzy_skin = none
+fuzzy_skin_first_layer = 0
+fuzzy_skin_point_distance = 0.8
+fuzzy_skin_thickness = 0.3
+gcode_add_line_number = 0
+gcode_comments = 0
+gcode_label_objects = 1
+hole_to_polyhole = 0
+hole_to_polyhole_threshold = 0.01
+hole_to_polyhole_twisted = 1
+independent_support_layer_height = 1
+infill_anchor = 400%
+infill_anchor_max = 20
+infill_jerk = 20
+initial_layer_jerk = 8
+initial_layer_min_bead_width = 85%
+initial_layer_travel_speed = 100%
+inner_wall_jerk = 20
+internal_bridge_flow = 1
+internal_bridge_speed = 150%
+internal_solid_infill_acceleration = 100%
+internal_solid_infill_pattern = monotonic
+ironing_angle = -1
+ironing_pattern = zig-zag
+ironing_support_layer = 0
+is_infill_first = 0
+make_overhang_printable = 0
+make_overhang_printable_angle = 55
+make_overhang_printable_hole_size = 0
+max_bridge_length = 10
+max_volumetric_extrusion_rate_slope = 0
+max_volumetric_extrusion_rate_slope_segment_length = 3
+min_bead_width = 85%
+min_feature_size = 25%
+min_width_top_surface = 300%
+minimum_support_area = 5
+mmu_segmented_region_interlocking_depth = 0
+mmu_segmented_region_max_width = 0
+only_one_wall_first_layer = 0
+only_one_wall_top = 0
+ooze_prevention = 0
+outer_wall_acceleration = 1000
+outer_wall_jerk = 20
+overhang_reverse = 0
+overhang_reverse_internal_only = 0
+overhang_reverse_threshold = 50%
+overhang_speed_classic = 0
+precise_outer_wall = 0
+prime_tower_brim_width = 3
+prime_volume = 45
+print_flow_ratio = 1
+raft_contact_distance = 0.1
+raft_expansion = 1.5
+raft_first_layer_density = 90%
+raft_first_layer_expansion = 2
+role_based_wipe_speed = 1
+seam_gap = 10%
+single_extruder_multi_material_priming = 0
+skirt_speed = 50
+slice_closing_radius = 0.049
+slicing_mode = regular
+slow_down_layers = 0
+slowdown_for_curled_perimeters = 0
+small_perimeter_speed = 50%
+small_perimeter_threshold = 0
+solid_infill_filament = 1
+sparse_infill_acceleration = 100%
+sparse_infill_filament = 1
+speed_limit_to_height = [[100,150,100,6000],[150,200,80,5500],[200,250,60,5000]]
+speed_limit_to_height_enable = 0
+spiral_mode_max_xy_smoothing = 200%
+spiral_mode_smooth = 0
+staggered_inner_seams = 0
+thick_bridges = 0
+thick_internal_bridges = 1
+timelapse_type = 0
+top_solid_infill_flow_ratio = 1
+top_surface_jerk = 20
+travel_jerk = 8
+travel_speed_z = 0
+wall_distribution_count = 1
+wall_filament = 1
+wall_generator = arachne
+wall_sequence = inner wall/outer wall
+wall_transition_angle = 10
+wall_transition_filter_deviation = 25%
+wall_transition_length = 100%
+wipe_before_external_loop = 0
+wipe_on_loops = 0
+wipe_speed = 80%
+wipe_tower_bridging = 10
+wipe_tower_cone_angle = 0
+wipe_tower_extra_spacing = 100%
+wipe_tower_rotation_angle = 0
+wiping_volumes_extruders = 70,70,70,70,70,70,70,70,70,70

print_config/prusa_slicer/quality/0.16mm_Optimal.ini

@@ -0,0 +1,200 @@
+[metadata]
+show_name = 0.16mm Optimal Quality
+
+
+[settings]
+adaptive_layer_height = 0
+reduce_crossing_wall = 0
+bridge_flow = 0.95
+bridge_speed = 100
+brim_width = 5
+print_sequence = by layer
+default_acceleration = 2500
+bridge_no_support = 0
+elefant_foot_compensation = 0
+outer_wall_line_width = 0.42
+outer_wall_speed = 60
+line_width = 0.46
+infill_direction = 45
+sparse_infill_density = 15%
+sparse_infill_pattern = grid
+initial_layer_line_width = 0.46
+initial_layer_print_height = 0.2
+initial_layer_speed = 30
+gap_infill_speed = 50
+infill_combination = 0
+sparse_infill_line_width = 0.45
+infill_wall_overlap = 15%
+sparse_infill_speed = 180
+interface_shells = 0
+detect_overhang_wall = 1
+reduce_infill_retraction = 1
+wall_loops = 2
+inner_wall_line_width = 0.45
+inner_wall_speed = 90
+print_settings_id = 
+raft_layers = 0
+seam_position = aligned
+skirt_distance = 2
+skirt_height = 2
+minimum_sparse_infill_area = 10
+internal_solid_infill_line_width = 0.42
+internal_solid_infill_speed = 180
+spiral_mode = 0
+standby_temperature_delta = -5
+detect_thin_wall = 1
+top_surface_line_width = 0.42
+top_surface_speed = 50
+travel_speed = 150
+enable_prime_tower = 0
+prime_tower_width = 60
+xy_hole_compensation = 0
+xy_contour_compensation = 0
+max_travel_detour_distance = 0
+bottom_surface_pattern = monotonic
+bottom_shell_layers = 4
+bottom_shell_thickness = 0
+brim_object_gap = 0.1
+compatible_printers_condition = 
+top_surface_acceleration = 2500
+draft_shield = disabled
+enable_arc_fitting = 0
+wall_infill_order = inner wall/outer wall/infill
+initial_layer_acceleration = 500
+travel_acceleration = 2500
+inner_wall_acceleration = 2000
+ironing_flow = 15%
+ironing_spacing = 0.1
+ironing_speed = 20
+ironing_type = no ironing
+layer_height = 0.16
+overhang_1_4_speed = 0
+overhang_2_4_speed = 20
+overhang_3_4_speed = 15
+overhang_4_4_speed = 10
+skirt_loops = 0
+resolution = 0.012
+top_surface_pattern = monotonic
+top_shell_layers = 6
+top_shell_thickness = 0.8
+initial_layer_infill_speed = 80
+wipe_tower_no_sparse_layers = 0
+accel_to_decel_enable = 1
+accel_to_decel_factor = 50%
+acceleration_limit_mess = [[0.5,1.0,100,6000],[1.0,1.5,80,5500],[1.5,2.0,60,5000]]
+acceleration_limit_mess_enable = 0
+alternate_extra_wall = 0
+bottom_solid_infill_flow_ratio = 1
+bridge_acceleration = 50%
+bridge_angle = 0
+bridge_density = 100%
+brim_ears_detection_length = 1
+brim_ears_max_angle = 125
+brim_type = no_brim
+default_jerk = 8
+detect_narrow_internal_solid_infill = 1
+elefant_foot_compensation_layers = 1
+enable_overhang_speed = 1
+enforce_support_layers = 0
+ensure_vertical_shell_thickness = ensure_all
+exclude_object = 0
+extra_perimeters_on_overhangs = 0
+filter_out_gap_fill = 0
+flush_into_infill = 0
+flush_into_objects = 0
+flush_into_support = 1
+fuzzy_skin = none
+fuzzy_skin_first_layer = 0
+fuzzy_skin_point_distance = 0.8
+fuzzy_skin_thickness = 0.3
+gcode_add_line_number = 0
+gcode_comments = 0
+gcode_label_objects = 1
+hole_to_polyhole = 0
+hole_to_polyhole_threshold = 0.01
+hole_to_polyhole_twisted = 1
+independent_support_layer_height = 1
+infill_anchor = 400%
+infill_anchor_max = 20
+infill_jerk = 20
+initial_layer_jerk = 8
+initial_layer_min_bead_width = 85%
+initial_layer_travel_speed = 100%
+inner_wall_jerk = 20
+internal_bridge_flow = 1
+internal_bridge_speed = 150%
+internal_solid_infill_acceleration = 100%
+internal_solid_infill_pattern = monotonic
+ironing_angle = -1
+ironing_pattern = zig-zag
+ironing_support_layer = 0
+is_infill_first = 0
+make_overhang_printable = 0
+make_overhang_printable_angle = 55
+make_overhang_printable_hole_size = 0
+max_bridge_length = 10
+max_volumetric_extrusion_rate_slope = 0
+max_volumetric_extrusion_rate_slope_segment_length = 3
+min_bead_width = 85%
+min_feature_size = 25%
+min_width_top_surface = 300%
+minimum_support_area = 5
+mmu_segmented_region_interlocking_depth = 0
+mmu_segmented_region_max_width = 0
+only_one_wall_first_layer = 0
+only_one_wall_top = 0
+ooze_prevention = 0
+outer_wall_acceleration = 1000
+outer_wall_jerk = 20
+overhang_reverse = 0
+overhang_reverse_internal_only = 0
+overhang_reverse_threshold = 50%
+overhang_speed_classic = 0
+precise_outer_wall = 0
+prime_tower_brim_width = 3
+prime_volume = 45
+print_flow_ratio = 1
+raft_contact_distance = 0.1
+raft_expansion = 1.5
+raft_first_layer_density = 90%
+raft_first_layer_expansion = 2
+role_based_wipe_speed = 1
+seam_gap = 10%
+single_extruder_multi_material_priming = 0
+skirt_speed = 50
+slice_closing_radius = 0.049
+slicing_mode = regular
+slow_down_layers = 0
+slowdown_for_curled_perimeters = 0
+small_perimeter_speed = 50%
+small_perimeter_threshold = 0
+solid_infill_filament = 1
+sparse_infill_acceleration = 100%
+sparse_infill_filament = 1
+speed_limit_to_height = [[100,150,100,6000],[150,200,80,5500],[200,250,60,5000]]
+speed_limit_to_height_enable = 0
+spiral_mode_max_xy_smoothing = 200%
+spiral_mode_smooth = 0
+staggered_inner_seams = 0
+thick_bridges = 0
+thick_internal_bridges = 1
+timelapse_type = 0
+top_solid_infill_flow_ratio = 1
+top_surface_jerk = 20
+travel_jerk = 8
+travel_speed_z = 0
+wall_distribution_count = 1
+wall_filament = 1
+wall_generator = arachne
+wall_sequence = inner wall/outer wall
+wall_transition_angle = 10
+wall_transition_filter_deviation = 25%
+wall_transition_length = 100%
+wipe_before_external_loop = 0
+wipe_on_loops = 0
+wipe_speed = 80%
+wipe_tower_bridging = 10
+wipe_tower_cone_angle = 0
+wipe_tower_extra_spacing = 100%
+wipe_tower_rotation_angle = 0
+wiping_volumes_extruders = 70,70,70,70,70,70,70,70,70,70

print_config/prusa_slicer/quality/0.20mm_Standard.ini

@@ -0,0 +1,226 @@
+[metadata]
+show_name = 0.20mm Standard Quality
+
+
+[settings]
+adaptive_layer_height = 0
+reduce_crossing_wall = 0
+bridge_flow = 0.95
+bridge_speed = 50
+brim_width = 5
+print_sequence = by layer
+default_acceleration = 2500
+bridge_no_support = 0
+elefant_foot_compensation = 0.15
+outer_wall_line_width = 0.42
+outer_wall_speed = 60
+line_width = 0.45
+infill_direction = 45
+sparse_infill_density = 15%
+sparse_infill_pattern = zig-zag
+initial_layer_line_width = 0.5
+initial_layer_print_height = 0.2
+initial_layer_speed = 30
+gap_infill_speed = 50
+infill_combination = 0
+sparse_infill_line_width = 0.45
+infill_wall_overlap = 30
+sparse_infill_speed = 180
+interface_shells = 0
+detect_overhang_wall = 1
+reduce_infill_retraction = 1
+wall_loops = 2
+inner_wall_line_width = 0.45
+inner_wall_speed = 90
+print_settings_id = 
+raft_layers = 0
+seam_position = aligned
+skirt_distance = 2
+skirt_height = 2
+minimum_sparse_infill_area = 10
+internal_solid_infill_line_width = 0.42
+internal_solid_infill_speed = 180
+spiral_mode = 0
+standby_temperature_delta = -5
+detect_thin_wall = 0
+top_surface_line_width = 0.42
+top_surface_speed = 50
+travel_speed = 150
+enable_prime_tower = 0
+prime_tower_width = 60
+xy_hole_compensation = 0
+xy_contour_compensation = 0
+max_travel_detour_distance = 0
+bottom_surface_pattern = monotonic
+bottom_shell_layers = 4
+bottom_shell_thickness = 0
+brim_object_gap = 0.1
+compatible_printers_condition = 
+top_surface_acceleration = 2500
+draft_shield = disabled
+enable_arc_fitting = 1
+wall_infill_order = inner wall/outer wall/infill
+initial_layer_acceleration = 500
+travel_acceleration = 2500
+inner_wall_acceleration = 2000
+ironing_flow = 15%
+ironing_spacing = 0.1
+ironing_speed = 20
+ironing_type = no ironing
+layer_height = 0.2
+overhang_1_4_speed = 0
+overhang_2_4_speed = 60
+overhang_3_4_speed = 30
+overhang_4_4_speed = 10
+skirt_loops = 0
+resolution = 0.012
+
+top_surface_pattern = monotonic
+top_shell_layers = 4
+top_shell_thickness = 0.8
+initial_layer_infill_speed = 80
+wipe_tower_no_sparse_layers = 0
+accel_to_decel_enable = 1
+accel_to_decel_factor = 25
+acceleration_limit_mess = [[0.5,1.0,100,6000],[1.0,1.5,80,5500],[1.5,2.0,60,5000]]
+acceleration_limit_mess_enable = 0
+ai_infill = 0
+alternate_extra_wall = 0
+bottom_solid_infill_flow_ratio = 1
+bridge_acceleration = 50%
+bridge_angle = 0
+bridge_density = 100%
+brim_ears_detection_length = 1
+brim_ears_max_angle = 125
+brim_type = no_brim
+counterbore_hole_bridging = none
+default_jerk = 10
+detect_narrow_internal_solid_infill = 1
+dont_filter_internal_bridges = disabled
+elefant_foot_compensation_layers = 1
+enable_overhang_speed = 1
+enforce_support_layers = 0
+ensure_vertical_shell_thickness = ensure_all
+exclude_object = 0
+extra_perimeters_on_overhangs = 0
+filter_out_gap_fill = 0
+flush_into_infill = 0
+flush_into_objects = 0
+flush_into_support = 1
+fuzzy_skin = none
+fuzzy_skin_first_layer = 0
+fuzzy_skin_point_distance = 0.8
+fuzzy_skin_thickness = 0.3
+gap_fill_target = everywhere
+gcode_add_line_number = 0
+gcode_comments = 0
+gcode_label_objects = 1
+hole_to_polyhole = 0
+hole_to_polyhole_threshold = 0.01
+hole_to_polyhole_twisted = 1
+independent_support_layer_height = 1
+infill_anchor = 400%
+infill_anchor_max = 20
+infill_jerk = 10
+initial_layer_jerk = 10
+initial_layer_min_bead_width = 85%
+initial_layer_travel_speed = 100%
+inner_wall_jerk = 10
+internal_bridge_flow = 1
+internal_bridge_speed = 150%
+internal_solid_infill_acceleration = 100%
+internal_solid_infill_pattern = monotonic
+ironing_angle = -1
+ironing_pattern = zig-zag
+ironing_support_layer = 0
+is_infill_first = 0
+make_overhang_printable = 0
+make_overhang_printable_angle = 55
+make_overhang_printable_hole_size = 0
+material_flow_dependent_temperature = 0
+material_flow_temp_graph = [[3.0,210],[10.0,220],[12.0,230]]
+max_bridge_length = 10
+max_volumetric_extrusion_rate_slope = 0
+max_volumetric_extrusion_rate_slope_segment_length = 3
+min_bead_width = 85%
+min_feature_size = 25%
+min_length_factor = 0.5
+min_width_top_surface = 300%
+minimum_support_area = 5
+mmu_segmented_region_interlocking_depth = 0
+mmu_segmented_region_max_width = 0
+only_one_wall_first_layer = 0
+only_one_wall_top = 1
+ooze_prevention = 0
+outer_wall_acceleration = 1000
+outer_wall_jerk = 10
+overhang_reverse = 0
+overhang_reverse_internal_only = 0
+overhang_reverse_threshold = 50%
+overhang_speed_classic = 0
+precise_outer_wall = 0
+prime_tower_brim_width = 3
+prime_tower_enhance_type = chamfer
+prime_volume = 45
+print_flow_ratio = 1
+print_order = default
+raft_contact_distance = 0.1
+raft_expansion = 1.5
+raft_first_layer_density = 90%
+raft_first_layer_expansion = 2
+role_based_wipe_speed = 0
+scarf_angle_threshold = 155
+scarf_joint_flow_ratio = 1
+scarf_joint_speed = 100%
+scarf_overhang_threshold = 40%
+seam_gap = 10%
+seam_slope_conditional = 0
+seam_slope_entire_loop = 0
+seam_slope_inner_walls = 0
+seam_slope_min_length = 20
+seam_slope_start_height = 0
+seam_slope_steps = 10
+seam_slope_type = none
+single_extruder_multi_material_priming = 0
+skirt_speed = 50
+slice_closing_radius = 0.049
+slicing_mode = regular
+slow_down_layers = 0
+slowdown_for_curled_perimeters = 0
+small_area_infill_flow_compensation = 0
+small_area_infill_flow_compensation_model = 0,0;"\n0.2,0.4444";"\n0.4,0.6145";"\n0.6,0.7059";"\n0.8,0.7619";"\n1.5,0.8571";"\n2,0.8889";"\n3,0.9231";"\n5,0.9520";"\n10,1"
+small_perimeter_speed = 50%
+small_perimeter_threshold = 0
+solid_infill_filament = 1
+sparse_infill_acceleration = 100%
+sparse_infill_filament = 1
+speed_limit_to_height = [[100,150,100,6000],[150,200,80,5500],[200,250,60,5000]]
+speed_limit_to_height_enable = 0
+spiral_mode_max_xy_smoothing = 200%
+spiral_mode_smooth = 0
+staggered_inner_seams = 1
+
+thick_bridges = 0
+thick_internal_bridges = 1
+timelapse_type = 0
+top_solid_infill_flow_ratio = 1
+top_surface_jerk = 8
+travel_jerk = 10
+travel_speed_z = 0
+
+wall_direction = auto
+wall_distribution_count = 1
+wall_filament = 1
+wall_generator = arachne
+wall_sequence = inner wall/outer wall
+wall_transition_angle = 10
+wall_transition_filter_deviation = 25%
+wall_transition_length = 100%
+wipe_before_external_loop = 0
+wipe_on_loops = 0
+wipe_speed = 100%
+wipe_tower_bridging = 10
+wipe_tower_cone_angle = 0
+wipe_tower_extra_spacing = 100%
+wipe_tower_rotation_angle = 0
+wiping_volumes_extruders = 70,70,70,70,70,70,70,70,70,70

print_config/prusa_slicer/supports/no_support.ini

@@ -0,0 +1,50 @@
+[metadata]
+show_name = No Support
+
+
+[settings]
+enable_support = 0
+support_filament = 0
+support_line_width = 0.4
+support_interface_filament = 0
+support_on_build_plate_only = 0
+support_top_z_distance = 0.2
+support_interface_loop_pattern = 0
+support_interface_top_layers = 2
+support_interface_spacing = 0.5
+support_interface_speed = 100%
+support_base_pattern = rectilinear
+support_base_pattern_spacing = 2.5
+support_speed = 50
+support_threshold_angle = 30
+support_object_xy_distance = 0.35
+
+support_type = normal(auto)
+support_style = default
+support_interface_bottom_layers = 2
+tree_support_branch_angle = 45
+tree_support_wall_count = 0
+
+support_angle = 0
+support_bottom_interface_spacing = 0.5
+support_bottom_z_distance = 0.2
+support_critical_regions_only = 0
+support_expansion = 0
+support_interface_not_for_body = 1
+support_interface_pattern = auto
+support_remove_small_overhang = 1
+support_xy_overrides_z = xy_overrides_z
+
+tree_support_adaptive_layer_height = 1
+tree_support_angle_slow = 25
+tree_support_auto_brim = 1
+tree_support_branch_angle_organic = 40
+tree_support_branch_diameter = 2
+tree_support_branch_diameter_angle = 5
+tree_support_branch_diameter_double_wall = 3
+tree_support_branch_diameter_organic = 2
+tree_support_branch_distance = 5
+tree_support_branch_distance_organic = 1
+tree_support_brim_width = 3
+tree_support_tip_diameter = 0.8
+tree_support_top_rate = 30%