修改了质量参数、添加了账户管理功能

Co-authored-by: Copilot <copilot@github.com>

print_config/prusa_slicer/materials/CR-PETG.ini

@@ -1,73 +1,73 @@
 [metadata]
 show_name = CR-PETG
-material_type = petg
+filament_type = petg
 
 
 [settings]
 ; filament_adhesiveness_category = 300
 idle_temperature = 160
 first_layer_bed_temperature = 70
-cool_plate_temp = 70
-eng_plate_temp = 0
-hot_plate_temp = 70
-textured_plate_temp = 70
-cool_plate_temp_initial_layer = 70
-eng_plate_temp_initial_layer = 0
-hot_plate_temp_initial_layer = 70
-textured_plate_temp_initial_layer = 70
-overhang_fan_threshold = 25%
-overhang_fan_speed = 90
-slow_down_for_layer_cooling = 1
-close_fan_the_first_x_layers = 3
-filament_end_gcode = ; filament end gcode \n
-filament_flow_ratio = 0.95
-reduce_fan_stop_start_freq = 1
-fan_cooling_layer_time = 30
+;;;cool_plate_temp = 70
+;;;eng_plate_temp = 0
+;;;hot_plate_temp = 70
+;;;textured_plate_temp = 70
+;;;cool_plate_temp_initial_layer = 70
+;;;eng_plate_temp_initial_layer = 0
+;;;hot_plate_temp_initial_layer = 70
+;;;textured_plate_temp_initial_layer = 70
+;;;overhang_fan_threshold = 25%
+;;;overhang_fan_speed = 90
+;;;slow_down_for_layer_cooling = 1
+;;;close_fan_the_first_x_layers = 3
+;;;filament_end_gcode = ; filament end gcode \n
+extrusion_multiplier = 0.95
+;;;reduce_fan_stop_start_freq = 1
+;;;fan_cooling_layer_time = 30
 filament_cost = 14
 filament_density = 1.23
-filament_deretraction_speed = nil
+filament_deretract_speed = nil
 filament_diameter = 1.75
 filament_max_volumetric_speed = 9
 filament_minimal_purge_on_wipe_tower = 15
-filament_retraction_minimum_travel = nil
+;;;filament_retraction_minimum_travel = nil
 filament_retract_before_wipe = nil
-filament_retract_when_changing_layer = nil
-filament_retraction_length = nil
-filament_z_hop = nil
-filament_z_hop_types = nil
+;;;filament_retract_when_changing_layer = nil
+filament_retract_length = nil
+;;;filament_z_hop = nil
+;;;filament_z_hop_types = nil
 filament_retract_restart_extra = 0
-filament_retraction_speed = nil
-filament_settings_id = 
+filament_retract_speed = nil
+;;;filament_settings_id = 
 filament_soluble = 0
 filament_type = PETG
-filament_vendor = Creality
+;;;filament_vendor = Creality
 filament_wipe = nil
-filament_wipe_distance = nil
-bed_type = Cool Plate
-nozzle_temperature_initial_layer = 230
+;;;filament_wipe_distance = nil
+;;;bed_type = Cool Plate
+first_layer_temperature = 230
 full_fan_speed_layer = 0
-fan_max_speed = 40
-fan_min_speed = 30
-slow_down_min_speed = 10
-slow_down_layer_time = 8
-filament_start_gcode = ; filament start gcode\n
-nozzle_temperature = 230
-temperature_vitrification = 80
-additional_cooling_fan_speed = 0
-complete_print_exhaust_fan_speed = 80
-cool_cds_fan_start_at_height = 0
-cool_special_cds_fan_speed = 0
+max_fan_speed = 40
+min_fan_speed = 30
+;;;slow_down_min_speed = 10
+slowdown_below_layer_time = 8
+;;;filament_start_gcode = ; filament start gcode\n
+temperature = 230
+;;;temperature_vitrification = 80
+;;;additional_cooling_fan_speed = 0
+;;;complete_print_exhaust_fan_speed = 80
+;;;cool_cds_fan_start_at_height = 0
+;;;cool_special_cds_fan_speed = 0
 default_filament_colour = ""
-during_print_exhaust_fan_speed = 60
-enable_overhang_bridge_fan = 1
-enable_pressure_advance = 1
-enable_special_area_additional_cooling_fan = 0
-epoxy_resin_plate_temp = 70
-epoxy_resin_plate_temp_initial_layer = 70
+;;;during_print_exhaust_fan_speed = 60
+;;;enable_overhang_bridge_fan = 1
+;;;enable_pressure_advance = 1
+;;;enable_special_area_additional_cooling_fan = 0
+;;;epoxy_resin_plate_temp = 70
+;;;epoxy_resin_plate_temp_initial_layer = 70
 filament_cooling_final_speed = 3.4
 filament_cooling_initial_speed = 2.2
 filament_cooling_moves = 4
-filament_is_support = 0
+;;;filament_is_support = 0
 filament_load_time = 0
 filament_loading_speed = 28
 filament_loading_speed_start = 3
@@ -78,16 +78,16 @@ filament_notes = ""
 filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
 filament_retract_lift_above = 0
 filament_retract_lift_below = 0
-filament_retract_lift_enforce = All Surfaces
-filament_shrink = 100%
+;;;filament_retract_lift_enforce = All Surfaces
+;;;filament_shrink = 100%
 filament_toolchange_delay = 0
 filament_unload_time = 0
 filament_unloading_speed = 90
 filament_unloading_speed_start = 100
-material_flow_dependent_temperature = 0
-material_flow_temp_graph = [[3.0,210],  [10.0,220],  [12.0,230]]
-nozzle_temperature_range_high = 270
-nozzle_temperature_range_low = 220
-pressure_advance = 0.08
-required_nozzle_HRC = 0
-support_material_interface_fan_speed = -1
+;;;material_flow_dependent_temperature = 0
+;;;material_flow_temp_graph = [[3.0,210],  [10.0,220],  [12.0,230]]
+;;;nozzle_temperature_range_high = 270
+;;;nozzle_temperature_range_low = 220
+;;;pressure_advance = 0.08
+;;;required_nozzle_HRC = 0
+;;;support_material_interface_fan_speed = -1

print_config/prusa_slicer/materials/CR-PLA.ini

@@ -1,78 +1,78 @@
 [metadata]
 show_name = CR-PLA
-material_type = pla
+filament_type = pla
 
 
 [settings]
 idle_temperature = 150
 first_layer_bed_temperature = 60
-cool_plate_temp = 50
-eng_plate_temp = 45
-hot_plate_temp = 50
-textured_plate_temp = 50
-cool_plate_temp_initial_layer = 50
-eng_plate_temp_initial_layer = 45
-hot_plate_temp_initial_layer = 50
-textured_plate_temp_initial_layer = 50
-overhang_fan_threshold = 50%
-overhang_fan_speed = 100
-slow_down_for_layer_cooling = 1
-close_fan_the_first_x_layers = 1
-filament_end_gcode = ;filament end gcode 
-filament_flow_ratio = 0.95
-reduce_fan_stop_start_freq = 1
-fan_cooling_layer_time = 100
+;;;cool_plate_temp = 50
+;;;eng_plate_temp = 45
+;;;hot_plate_temp = 50
+;;;textured_plate_temp = 50
+;;;cool_plate_temp_initial_layer = 50
+;;;eng_plate_temp_initial_layer = 45
+;;;hot_plate_temp_initial_layer = 50
+;;;textured_plate_temp_initial_layer = 50
+;;;overhang_fan_threshold = 50%
+;;;overhang_fan_speed = 100
+;;;slow_down_for_layer_cooling = 1
+;;;close_fan_the_first_x_layers = 1
+;;;filament_end_gcode = ;filament end gcode
+extrusion_multiplier = 0.95
+;;;reduce_fan_stop_start_freq = 1
+;;;fan_cooling_layer_time = 100
 filament_cost = 25
 filament_density = 1.25
-filament_deretraction_speed = nil
+filament_deretract_speed = nil
 filament_diameter = 1.75
 filament_max_volumetric_speed = 12
 filament_minimal_purge_on_wipe_tower = 15
-filament_retraction_minimum_travel = nil
+;;;filament_retraction_minimum_travel = nil
 filament_retract_before_wipe = nil
-filament_retract_when_changing_layer = nil
-filament_retraction_length = 1
-filament_z_hop = 0.2
-filament_z_hop_types = Slope Lift
+;;;filament_retract_when_changing_layer = nil
+filament_retract_length = 1
+;;;filament_z_hop = 0.2
+;;;filament_z_hop_types = Slope Lift
 filament_retract_restart_extra = 0
-filament_retraction_speed = 40
-filament_settings_id = 
+filament_retract_speed = 40
+;;;filament_settings_id = 
 filament_soluble = 0
 filament_type = PLA
-filament_vendor = Creality
+;;;filament_vendor = Creality
 filament_wipe = nil
-filament_wipe_distance = nil
-bed_type = Cool Plate
-nozzle_temperature_initial_layer = 190
+;;;filament_wipe_distance = nil
+;;;bed_type = Cool Plate
+first_layer_temperature = 190
 full_fan_speed_layer = 0
-fan_max_speed = 100
-fan_min_speed = 100
-slow_down_min_speed = 20
-slow_down_layer_time = 6
-filament_start_gcode = ;filament start gcode
-nozzle_temperature = 190
-temperature_vitrification = 100
+max_fan_speed = 100
+min_fan_speed = 100
+;;;slow_down_min_speed = 20
+slowdown_below_layer_time = 6
+;;;filament_start_gcode = ;filament start gcode
+temperature = 190
+;;;temperature_vitrification = 100
 ; filament_adhesiveness_category = 100
-nozzle_temperature_range_low = 190
-nozzle_temperature_range_high = 240
-additional_cooling_fan_speed = 0
-activate_air_filtration = 0
-activate_chamber_temp_control = 0
+;;;nozzle_temperature_range_low = 190
+;;;nozzle_temperature_range_high = 240
+;;;additional_cooling_fan_speed = 0
+;;;activate_air_filtration = 0
+;;;activate_chamber_temp_control = 0
 chamber_temperature = 0
-complete_print_exhaust_fan_speed = 80
-cool_cds_fan_start_at_height = 0
-cool_special_cds_fan_speed = 0
+;;;complete_print_exhaust_fan_speed = 80
+;;;cool_cds_fan_start_at_height = 0
+;;;cool_special_cds_fan_speed = 0
 default_filament_colour = ""
-during_print_exhaust_fan_speed = 60
-enable_overhang_bridge_fan = 1
-enable_pressure_advance = 0
-enable_special_area_additional_cooling_fan = 0
-epoxy_resin_plate_temp = 0
-epoxy_resin_plate_temp_initial_layer = 0
+;;;during_print_exhaust_fan_speed = 60
+;;;enable_overhang_bridge_fan = 1
+;;;enable_pressure_advance = 0
+;;;enable_special_area_additional_cooling_fan = 0
+;;;epoxy_resin_plate_temp = 0
+;;;epoxy_resin_plate_temp_initial_layer = 0
 filament_cooling_final_speed = 3.4
 filament_cooling_initial_speed = 2.2
 filament_cooling_moves = 4
-filament_is_support = 0
+;;;filament_is_support = 0
 filament_load_time = 0
 filament_loading_speed = 28
 filament_loading_speed_start = 3
@@ -83,14 +83,14 @@ filament_notes = ""
 filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
 filament_retract_lift_above = 0
 filament_retract_lift_below = 0
-filament_retract_lift_enforce = All Surfaces
-filament_shrink = 100%
+;;;filament_retract_lift_enforce = All Surfaces
+;;;filament_shrink = 100%
 filament_toolchange_delay = 0
 filament_unload_time = 0
 filament_unloading_speed = 90
 filament_unloading_speed_start = 100
-material_flow_dependent_temperature = 0
-material_flow_temp_graph = [[2.0,185],[4.0,190],[7.0,200]]
-pressure_advance = 0.02
-required_nozzle_HRC = 0
-support_material_interface_fan_speed = -1
+;;;material_flow_dependent_temperature = 0
+;;;material_flow_temp_graph = [[2.0,185],[4.0,190],[7.0,200]]
+;;;pressure_advance = 0.02
+;;;required_nozzle_HRC = 0
+;;;support_material_interface_fan_speed = -1

print_config/prusa_slicer/materials/Generic_PETG.ini

@@ -1,76 +1,76 @@
 [metadata]
 show_name = Generic PETG
-material_type = petg
+filament_type = petg
 
 
 [settings]
 ; filament_adhesiveness_category = 300
 idle_temperature = 160
 first_layer_bed_temperature = 70
-cool_plate_temp = 60
-eng_plate_temp = 0
-hot_plate_temp = 70
-textured_plate_temp = 70
-cool_plate_temp_initial_layer = 60
-eng_plate_temp_initial_layer = 0
-hot_plate_temp_initial_layer = 70
-textured_plate_temp_initial_layer = 70
-overhang_fan_threshold = 25%
-overhang_fan_speed = 90
-slow_down_for_layer_cooling = 1
-close_fan_the_first_x_layers = 3
-filament_end_gcode = ;filament end gcode \n
-filament_flow_ratio = 0.95
-reduce_fan_stop_start_freq = 1
-fan_cooling_layer_time = 30
+;;;cool_plate_temp = 60
+;;;eng_plate_temp = 0
+;;;hot_plate_temp = 70
+;;;textured_plate_temp = 70
+;;;cool_plate_temp_initial_layer = 60
+;;;eng_plate_temp_initial_layer = 0
+;;;hot_plate_temp_initial_layer = 70
+;;;textured_plate_temp_initial_layer = 70
+;;;overhang_fan_threshold = 25%
+;;;overhang_fan_speed = 90
+;;;slow_down_for_layer_cooling = 1
+;;;close_fan_the_first_x_layers = 3
+;;;filament_end_gcode = ;filament end gcode \n
+extrusion_multiplier = 0.95
+;;;reduce_fan_stop_start_freq = 1
+;;;fan_cooling_layer_time = 30
 filament_cost = 30
 filament_density = 1.27
-filament_deretraction_speed = nil
+filament_deretract_speed = nil
 filament_diameter = 1.75
 filament_max_volumetric_speed = 10
 filament_minimal_purge_on_wipe_tower = 15
-filament_retraction_minimum_travel = nil
+;;;filament_retraction_minimum_travel = nil
 filament_retract_before_wipe = nil
-filament_retract_when_changing_layer = nil
-filament_retraction_length = 1.2
-filament_z_hop = 0.2
-filament_z_hop_types = nil
+;;;filament_retract_when_changing_layer = nil
+filament_retract_length = 1.2
+;;;filament_z_hop = 0.2
+;;;filament_z_hop_types = nil
 filament_retract_restart_extra = 0
-filament_retraction_speed = nil
-filament_settings_id = 
+filament_retract_speed = nil
+;;;filament_settings_id = 
 filament_soluble = 0
 filament_type = PETG
-filament_vendor = Creality
+;;;filament_vendor = Creality
 filament_wipe = nil
-filament_wipe_distance = nil
-bed_type = Cool Plate
-nozzle_temperature_initial_layer = 220
+;;;filament_wipe_distance = nil
+;;;bed_type = Cool Plate
+first_layer_temperature = 220
 full_fan_speed_layer = 0
-fan_max_speed = 80
-fan_min_speed = 40
-slow_down_min_speed = 10
-slow_down_layer_time = 8
-filament_start_gcode = ;filament start gcode\n
-nozzle_temperature = 220
-temperature_vitrification = 80
-activate_air_filtration = 0
-activate_chamber_temp_control = 0
-additional_cooling_fan_speed = 0
+max_fan_speed = 80
+min_fan_speed = 40
+;;;slow_down_min_speed = 10
+slowdown_below_layer_time = 8
+;;;filament_start_gcode = ;filament start gcode\n
+temperature = 220
+;;;temperature_vitrification = 80
+;;;activate_air_filtration = 0
+;;;activate_chamber_temp_control = 0
+;;;additional_cooling_fan_speed = 0
 chamber_temperature = 0
-complete_print_exhaust_fan_speed = 80
-cool_cds_fan_start_at_height = 0
-cool_special_cds_fan_speed = 0
+;;;complete_print_exhaust_fan_speed = 80
+;;;cool_cds_fan_start_at_height = 0
+;;;cool_special_cds_fan_speed = 0
 default_filament_colour = ""
-during_print_exhaust_fan_speed = 60
-enable_overhang_bridge_fan = 1
-enable_pressure_advance = 0
-enable_special_area_additional_cooling_fan = 0
-epoxy_resin_plate_temp = 0
-epoxy_resin_plate_temp_initial_layer = 0
+;;;during_print_exhaust_fan_speed = 60
+;;;enable_overhang_bridge_fan = 1
+;;;enable_pressure_advance = 0
+;;;enable_special_area_additional_cooling_fan = 0
+;;;epoxy_resin_plate_temp = 0
+;;;epoxy_resin_plate_temp_initial_layer = 0
 filament_cooling_final_speed = 3.4
 filament_cooling_initial_speed = 2.2
 filament_cooling_moves = 4
-filament_is_support = 0
+;;;filament_is_support = 0
 filament_load_time = 0
 filament_loading_speed = 28
 filament_loading_speed_start = 3
@@ -81,16 +81,16 @@ filament_notes = ""
 filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
 filament_retract_lift_above = 0
 filament_retract_lift_below = 0
-filament_retract_lift_enforce = All Surfaces
-filament_shrink = 100%
+;;;filament_retract_lift_enforce = All Surfaces
+;;;filament_shrink = 100%
 filament_toolchange_delay = 0
 filament_unload_time = 0
 filament_unloading_speed = 90
 filament_unloading_speed_start = 100
-material_flow_dependent_temperature = 0
-material_flow_temp_graph = [[3.5,200],[7.0,240]]
-nozzle_temperature_range_high = 270
-nozzle_temperature_range_low = 220
-pressure_advance = 0.02
-required_nozzle_HRC = 0
-support_material_interface_fan_speed = -1
+;;;material_flow_dependent_temperature = 0
+;;;material_flow_temp_graph = [[3.5,200],[7.0,240]]
+;;;nozzle_temperature_range_high = 270
+;;;nozzle_temperature_range_low = 220
+;;;pressure_advance = 0.02
+;;;required_nozzle_HRC = 0
+;;;support_material_interface_fan_speed = -1

print_config/prusa_slicer/materials/Generic_TPU.ini

@@ -1,78 +1,78 @@
 [metadata]
 show_name = Generic TPU
-material_type = tpu
+filament_type = tpu
 
 
 [settings]
 idle_temperature = 130
 first_layer_bed_temperature = 55
-cool_plate_temp = 30
-eng_plate_temp = 30
-hot_plate_temp = 30
-textured_plate_temp = 30
-cool_plate_temp_initial_layer = 30
-eng_plate_temp_initial_layer = 30
-hot_plate_temp_initial_layer = 30
-textured_plate_temp_initial_layer = 30
-overhang_fan_threshold = 95%
-overhang_fan_speed = 100
-slow_down_for_layer_cooling = 1
-close_fan_the_first_x_layers = 1
-filament_end_gcode = ;filament end gcode \n
-filament_flow_ratio = 1
-reduce_fan_stop_start_freq = 1
-fan_cooling_layer_time = 100
+;;;cool_plate_temp = 30
+;;;eng_plate_temp = 30
+;;;hot_plate_temp = 30
+;;;textured_plate_temp = 30
+;;;cool_plate_temp_initial_layer = 30
+;;;eng_plate_temp_initial_layer = 30
+;;;hot_plate_temp_initial_layer = 30
+;;;textured_plate_temp_initial_layer = 30
+;;;overhang_fan_threshold = 95%
+;;;overhang_fan_speed = 100
+;;;slow_down_for_layer_cooling = 1
+;;;close_fan_the_first_x_layers = 1
+;;;filament_end_gcode = ;filament end gcode \n
+extrusion_multiplier = 1
+;;;reduce_fan_stop_start_freq = 1
+;;;fan_cooling_layer_time = 100
 filament_cost = 20
 filament_density = 1.24
-filament_deretraction_speed = nil
+filament_deretract_speed = nil
 filament_diameter = 1.75
 filament_max_volumetric_speed = 3
 filament_minimal_purge_on_wipe_tower = 15
-filament_retraction_minimum_travel = nil
+;;;filament_retraction_minimum_travel = nil
 filament_retract_before_wipe = nil
-filament_retract_when_changing_layer = nil
-filament_retraction_length = 2
-filament_z_hop = 0.2
-filament_z_hop_types = nil
+;;;filament_retract_when_changing_layer = nil
+filament_retract_length = 2
+;;;filament_z_hop = 0.2
+;;;filament_z_hop_types = nil
 filament_retract_restart_extra = 0
-filament_retraction_speed = nil
-filament_settings_id = 
+filament_retract_speed = nil
+;;;filament_settings_id = 
 filament_soluble = 0
 filament_type = TPU
-filament_vendor = Generic
+;;;filament_vendor = Generic
 filament_wipe = nil
-filament_wipe_distance = nil
-bed_type = Cool Plate
-nozzle_temperature_initial_layer = 200
+;;;filament_wipe_distance = nil
+;;;bed_type = Cool Plate
+first_layer_temperature = 200
 full_fan_speed_layer = 0
-fan_max_speed = 100
-fan_min_speed = 100
-slow_down_min_speed = 10
-slow_down_layer_time = 12
-filament_start_gcode = ;filament start gcode\n
-nozzle_temperature = 200
-temperature_vitrification = 60
+max_fan_speed = 100
+min_fan_speed = 100
+;;;slow_down_min_speed = 10
+slowdown_below_layer_time = 12
+;;;filament_start_gcode = ;filament start gcode\n
+temperature = 200
+;;;temperature_vitrification = 60
 ; filament_adhesiveness_category = 600
-additional_cooling_fan_speed = 0
-nozzle_temperature_range_low = 200
-nozzle_temperature_range_high = 250
-activate_air_filtration = 0
-activate_chamber_temp_control = 0
+;;;additional_cooling_fan_speed = 0
+;;;nozzle_temperature_range_low = 200
+;;;nozzle_temperature_range_high = 250
+;;;activate_air_filtration = 0
+;;;activate_chamber_temp_control = 0
 chamber_temperature = 0
-complete_print_exhaust_fan_speed = 80
-cool_cds_fan_start_at_height = 0
-cool_special_cds_fan_speed = 0
+;;;complete_print_exhaust_fan_speed = 80
+;;;cool_cds_fan_start_at_height = 0
+;;;cool_special_cds_fan_speed = 0
 default_filament_colour = ""
-during_print_exhaust_fan_speed = 60
-enable_overhang_bridge_fan = 1
-enable_pressure_advance = 0
-enable_special_area_additional_cooling_fan = 0
-epoxy_resin_plate_temp = 0
-epoxy_resin_plate_temp_initial_layer = 0
+;;;during_print_exhaust_fan_speed = 60
+;;;enable_overhang_bridge_fan = 1
+;;;enable_pressure_advance = 0
+;;;enable_special_area_additional_cooling_fan = 0
+;;;epoxy_resin_plate_temp = 0
+;;;epoxy_resin_plate_temp_initial_layer = 0
 filament_cooling_final_speed = 3.4
 filament_cooling_initial_speed = 2.2
 filament_cooling_moves = 4
-filament_is_support = 0
+;;;filament_is_support = 0
 filament_load_time = 0
 filament_loading_speed = 28
 filament_loading_speed_start = 3
@@ -83,14 +83,14 @@ filament_notes = ""
 filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
 filament_retract_lift_above = 0
 filament_retract_lift_below = 0
-filament_retract_lift_enforce = All Surfaces
-filament_shrink = 100%
+;;;filament_retract_lift_enforce = All Surfaces
+;;;filament_shrink = 100%
 filament_toolchange_delay = 0
 filament_unload_time = 0
 filament_unloading_speed = 90
 filament_unloading_speed_start = 100
-material_flow_dependent_temperature = 0
-material_flow_temp_graph = [[3.5,200],[7.0,240]]
-pressure_advance = 0.02
-required_nozzle_HRC = 0
-support_material_interface_fan_speed = -1
+;;;material_flow_dependent_temperature = 0
+;;;material_flow_temp_graph = [[3.5,200],[7.0,240]]
+;;;pressure_advance = 0.02
+;;;required_nozzle_HRC = 0
+;;;support_material_interface_fan_speed = -1

print_config/prusa_slicer/materials/Hyper_L-W_PLA.ini

@@ -1,80 +1,80 @@
 [metadata]
 show_name = Hyper L-W PLA
-material_type = pla
+filament_type = pla
 
 
 [settings]
 idle_temperature = 150
 first_layer_bed_temperature = 60
-cool_plate_temp = 50
-eng_plate_temp = 45
-hot_plate_temp = 60
-textured_plate_temp = 60
-cool_plate_temp_initial_layer = 50
-eng_plate_temp_initial_layer = 45
-hot_plate_temp_initial_layer = 60
-textured_plate_temp_initial_layer = 60
-overhang_fan_threshold = 50%
-overhang_fan_speed = 100
-slow_down_for_layer_cooling = 1
-close_fan_the_first_x_layers = 1
-filament_end_gcode = ;filament end gcode 
-filament_flow_ratio = 0.75
-reduce_fan_stop_start_freq = 1
-fan_cooling_layer_time = 100
+;;;cool_plate_temp = 50
+;;;eng_plate_temp = 45
+;;;hot_plate_temp = 60
+;;;textured_plate_temp = 60
+;;;cool_plate_temp_initial_layer = 50
+;;;eng_plate_temp_initial_layer = 45
+;;;hot_plate_temp_initial_layer = 60
+;;;textured_plate_temp_initial_layer = 60
+;;;overhang_fan_threshold = 50%
+;;;overhang_fan_speed = 100
+;;;slow_down_for_layer_cooling = 1
+;;;close_fan_the_first_x_layers = 1
+;;;filament_end_gcode = ;filament end gcode
+extrusion_multiplier = 0.75
+;;;reduce_fan_stop_start_freq = 1
+;;;fan_cooling_layer_time = 100
 filament_cost = 48.9
 filament_density = 1.21
-filament_deretraction_speed = 15
+filament_deretract_speed = 15
 filament_diameter = 1.75
 filament_max_volumetric_speed = 4
 filament_minimal_purge_on_wipe_tower = 15
-filament_retraction_minimum_travel = 3
+;;;filament_retraction_minimum_travel = 3
 filament_retract_before_wipe = nil
-filament_retract_when_changing_layer = nil
-filament_retraction_length = 0.6
-filament_z_hop = nil
-filament_z_hop_types = nil
+;;;filament_retract_when_changing_layer = nil
+filament_retract_length = 0.6
+;;;filament_z_hop = nil
+;;;filament_z_hop_types = nil
 filament_retract_restart_extra = nil
-filament_retraction_speed = 15
-filament_settings_id = 
+filament_retract_speed = 15
+;;;filament_settings_id = 
 filament_soluble = 0
 filament_type = PLA
-filament_vendor = Creality
+;;;filament_vendor = Creality
 filament_wipe = nil
-filament_wipe_distance = nil
-bed_type = Cool Plate
-nozzle_temperature_initial_layer = 220
+;;;filament_wipe_distance = nil
+;;;bed_type = Cool Plate
+first_layer_temperature = 220
 full_fan_speed_layer = 0
-fan_max_speed = 100
-fan_min_speed = 60
-slow_down_min_speed = 10
-slow_down_layer_time = 10
-filament_start_gcode = ;filament start gcode
-nozzle_temperature = 220
-temperature_vitrification = 60
+max_fan_speed = 100
+min_fan_speed = 60
+;;;slow_down_min_speed = 10
+slowdown_below_layer_time = 10
+;;;filament_start_gcode = ;filament start gcode
+temperature = 220
+;;;temperature_vitrification = 60
 ; filament_adhesiveness_category = 100
-nozzle_temperature_range_low = 200
-nozzle_temperature_range_high = 270
-additional_cooling_fan_speed = 0
-activate_air_filtration = 0
-activate_chamber_temp_control = 0
+;;;nozzle_temperature_range_low = 200
+;;;nozzle_temperature_range_high = 270
+;;;additional_cooling_fan_speed = 0
+;;;activate_air_filtration = 0
+;;;activate_chamber_temp_control = 0
 chamber_temperature = 0
-complete_print_exhaust_fan_speed = 80
-cool_cds_fan_start_at_height = 0.5
-cool_special_cds_fan_speed = 0
-customized_plate_temp = 60
-customized_plate_temp_initial_layer = 60
+;;;complete_print_exhaust_fan_speed = 80
+;;;cool_cds_fan_start_at_height = 0.5
+;;;cool_special_cds_fan_speed = 0
+;;;customized_plate_temp = 60
+;;;customized_plate_temp_initial_layer = 60
 default_filament_colour = ""
-during_print_exhaust_fan_speed = 60
-enable_overhang_bridge_fan = 1
-enable_pressure_advance = 1
-enable_special_area_additional_cooling_fan = 0
-epoxy_resin_plate_temp = 60
-epoxy_resin_plate_temp_initial_layer = 60
+;;;during_print_exhaust_fan_speed = 60
+;;;enable_overhang_bridge_fan = 1
+;;;enable_pressure_advance = 1
+;;;enable_special_area_additional_cooling_fan = 0
+;;;epoxy_resin_plate_temp = 60
+;;;epoxy_resin_plate_temp_initial_layer = 60
 filament_cooling_final_speed = 3.4
 filament_cooling_initial_speed = 2.2
 filament_cooling_moves = 4
-filament_is_support = 0
+;;;filament_is_support = 0
 filament_load_time = 0
 filament_loading_speed = 28
 filament_loading_speed_start = 3
@@ -85,14 +85,14 @@ filament_notes = ""
 filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
 filament_retract_lift_above = nil
 filament_retract_lift_below = nil
-filament_retract_lift_enforce = nil
-filament_shrink = 100%
+;;;filament_retract_lift_enforce = nil
+;;;filament_shrink = 100%
 filament_shrinkage_compensation_z = 100%
 filament_toolchange_delay = 0
 filament_unload_time = 0
 filament_unloading_speed = 90
 filament_unloading_speed_start = 100
-material_flow_dependent_temperature = 0
-pressure_advance = 0.1
-required_nozzle_HRC = 0
-support_material_interface_fan_speed = -1
+;;;material_flow_dependent_temperature = 0
+;;;pressure_advance = 0.1
+;;;required_nozzle_HRC = 0
+;;;support_material_interface_fan_speed = -1

print_config/prusa_slicer/materials/Hyper_Marble_PLA.ini

@@ -1,80 +1,80 @@
 [metadata]
 show_name = Hyper Marble PLA
-material_type = pla
+filament_type = pla
 
 
 [settings]
 idle_temperature = 150
 first_layer_bed_temperature = 60
-cool_plate_temp = 50
-eng_plate_temp = 45
-hot_plate_temp = 50
-textured_plate_temp = 50
-cool_plate_temp_initial_layer = 50
-eng_plate_temp_initial_layer = 45
-hot_plate_temp_initial_layer = 50
-textured_plate_temp_initial_layer = 50
-overhang_fan_threshold = 50%
-overhang_fan_speed = 100
-slow_down_for_layer_cooling = 1
-close_fan_the_first_x_layers = 1
-filament_end_gcode = ;filament end gcode 
-filament_flow_ratio = 0.95
-reduce_fan_stop_start_freq = 1
-fan_cooling_layer_time = 100
+;;;cool_plate_temp = 50
+;;;eng_plate_temp = 45
+;;;hot_plate_temp = 50
+;;;textured_plate_temp = 50
+;;;cool_plate_temp_initial_layer = 50
+;;;eng_plate_temp_initial_layer = 45
+;;;hot_plate_temp_initial_layer = 50
+;;;textured_plate_temp_initial_layer = 50
+;;;overhang_fan_threshold = 50%
+;;;overhang_fan_speed = 100
+;;;slow_down_for_layer_cooling = 1
+;;;close_fan_the_first_x_layers = 1
+;;;filament_end_gcode = ;filament end gcode
+extrusion_multiplier = 0.95
+;;;reduce_fan_stop_start_freq = 1
+;;;fan_cooling_layer_time = 100
 filament_cost = 23.9
 filament_density = 1.25
-filament_deretraction_speed = 15
+filament_deretract_speed = 15
 filament_diameter = 1.75
 filament_max_volumetric_speed = 18
 filament_minimal_purge_on_wipe_tower = 15
-filament_retraction_minimum_travel = 2
+;;;filament_retraction_minimum_travel = 2
 filament_retract_before_wipe = nil
-filament_retract_when_changing_layer = nil
-filament_retraction_length = 1.5
-filament_z_hop = nil
-filament_z_hop_types = nil
+;;;filament_retract_when_changing_layer = nil
+filament_retract_length = 1.5
+;;;filament_z_hop = nil
+;;;filament_z_hop_types = nil
 filament_retract_restart_extra = nil
-filament_retraction_speed = 15
-filament_settings_id = 
+filament_retract_speed = 15
+;;;filament_settings_id = 
 filament_soluble = 0
 filament_type = PLA
-filament_vendor = Creality
+;;;filament_vendor = Creality
 filament_wipe = nil
-filament_wipe_distance = 3
-bed_type = Cool Plate
-nozzle_temperature_initial_layer = 220
+;;;filament_wipe_distance = 3
+;;;bed_type = Cool Plate
+first_layer_temperature = 220
 full_fan_speed_layer = 0
-fan_max_speed = 100
-fan_min_speed = 100
-slow_down_min_speed = 20
-slow_down_layer_time = 14
-filament_start_gcode = ;filament start gcode
-nozzle_temperature = 220
-temperature_vitrification = 60
+max_fan_speed = 100
+min_fan_speed = 100
+;;;slow_down_min_speed = 20
+slowdown_below_layer_time = 14
+;;;filament_start_gcode = ;filament start gcode
+temperature = 220
+;;;temperature_vitrification = 60
 ; filament_adhesiveness_category = 100
-nozzle_temperature_range_low = 190
-nozzle_temperature_range_high = 240
-additional_cooling_fan_speed = 0
-activate_air_filtration = 0
-activate_chamber_temp_control = 0
+;;;nozzle_temperature_range_low = 190
+;;;nozzle_temperature_range_high = 240
+;;;additional_cooling_fan_speed = 0
+;;;activate_air_filtration = 0
+;;;activate_chamber_temp_control = 0
 chamber_temperature = 0
-complete_print_exhaust_fan_speed = 80
-cool_cds_fan_start_at_height = 0
-cool_special_cds_fan_speed = 0
-customized_plate_temp = 50
-customized_plate_temp_initial_layer = 50
+;;;complete_print_exhaust_fan_speed = 80
+;;;cool_cds_fan_start_at_height = 0
+;;;cool_special_cds_fan_speed = 0
+;;;customized_plate_temp = 50
+;;;customized_plate_temp_initial_layer = 50
 default_filament_colour = ""
-during_print_exhaust_fan_speed = 60
-enable_overhang_bridge_fan = 1
-enable_pressure_advance = 1
-enable_special_area_additional_cooling_fan = 0
-epoxy_resin_plate_temp = 50
-epoxy_resin_plate_temp_initial_layer = 50
+;;;during_print_exhaust_fan_speed = 60
+;;;enable_overhang_bridge_fan = 1
+;;;enable_pressure_advance = 1
+;;;enable_special_area_additional_cooling_fan = 0
+;;;epoxy_resin_plate_temp = 50
+;;;epoxy_resin_plate_temp_initial_layer = 50
 filament_cooling_final_speed = 3.4
 filament_cooling_initial_speed = 2.2
 filament_cooling_moves = 4
-filament_is_support = 0
+;;;filament_is_support = 0
 filament_load_time = 0
 filament_loading_speed = 28
 filament_loading_speed_start = 3
@@ -85,15 +85,15 @@ filament_notes = ""
 filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
 filament_retract_lift_above = nil
 filament_retract_lift_below = nil
-filament_retract_lift_enforce = nil
-filament_shrink = 100%
+;;;filament_retract_lift_enforce = nil
+;;;filament_shrink = 100%
 filament_shrinkage_compensation_z = 100%
 filament_toolchange_delay = 0
 filament_unload_time = 0
 filament_unloading_speed = 90
 filament_unloading_speed_start = 100
-material_flow_dependent_temperature = 0
-material_flow_temp_graph = [[0.8,200],[1.0,200],[1.2,220]]
-pressure_advance = 0.04
-required_nozzle_HRC = 0
-support_material_interface_fan_speed = -1
+;;;material_flow_dependent_temperature = 0
+;;;material_flow_temp_graph = [[0.8,200],[1.0,200],[1.2,220]]
+;;;pressure_advance = 0.04
+;;;required_nozzle_HRC = 0
+;;;support_material_interface_fan_speed = -1

print_config/prusa_slicer/materials/Hyper_PETG.ini

@@ -1,75 +1,75 @@
 [metadata]
 show_name = Hyper PETG
-material_type = petg
+filament_type = petg
 
 
 [settings]
 ; filament_adhesiveness_category = 300
 idle_temperature = 160
-cool_plate_temp = 60
-eng_plate_temp = 0
-hot_plate_temp = 70
-textured_plate_temp = 70
-cool_plate_temp_initial_layer = 60
-eng_plate_temp_initial_layer = 0
-hot_plate_temp_initial_layer = 70
-textured_plate_temp_initial_layer = 70
-overhang_fan_threshold = 25%
-overhang_fan_speed = 90
-slow_down_for_layer_cooling = 1
-close_fan_the_first_x_layers = 3
-filament_end_gcode = ;filament end gcode \n
-filament_flow_ratio = 1.0
-reduce_fan_stop_start_freq = 1
-fan_cooling_layer_time = 30
+;;;cool_plate_temp = 60
+;;;eng_plate_temp = 0
+;;;hot_plate_temp = 70
+;;;textured_plate_temp = 70
+;;;cool_plate_temp_initial_layer = 60
+;;;eng_plate_temp_initial_layer = 0
+;;;hot_plate_temp_initial_layer = 70
+;;;textured_plate_temp_initial_layer = 70
+;;;overhang_fan_threshold = 25%
+;;;overhang_fan_speed = 90
+;;;slow_down_for_layer_cooling = 1
+;;;close_fan_the_first_x_layers = 3
+;;;filament_end_gcode = ;filament end gcode \n
+extrusion_multiplier = 1.0
+;;;reduce_fan_stop_start_freq = 1
+;;;fan_cooling_layer_time = 30
 filament_cost = 69
 filament_density = 1.27
-filament_deretraction_speed = nil
+filament_deretract_speed = nil
 filament_diameter = 1.75
 filament_max_volumetric_speed = 10
 filament_minimal_purge_on_wipe_tower = 15
-filament_retraction_minimum_travel = nil
+;;;filament_retraction_minimum_travel = nil
 filament_retract_before_wipe = nil
-filament_retract_when_changing_layer = nil
-filament_retraction_length = 1.2
-filament_z_hop = 0.2
-filament_z_hop_types = nil
+;;;filament_retract_when_changing_layer = nil
+filament_retract_length = 1.2
+;;;filament_z_hop = 0.2
+;;;filament_z_hop_types = nil
 filament_retract_restart_extra = 0
-filament_retraction_speed = nil
-filament_settings_id = 
+filament_retract_speed = nil
+;;;filament_settings_id = 
 filament_soluble = 0
 filament_type = PETG
-filament_vendor = Creality
+;;;filament_vendor = Creality
 filament_wipe = nil
-filament_wipe_distance = 2
-bed_type = Cool Plate
-nozzle_temperature_initial_layer = 235
+;;;filament_wipe_distance = 2
+;;;bed_type = Cool Plate
+first_layer_temperature = 235
 full_fan_speed_layer = 0
-fan_max_speed = 80
-fan_min_speed = 40
-slow_down_min_speed = 10
-slow_down_layer_time = 8
-filament_start_gcode = ;filament start gcode\n
-nozzle_temperature = 240
-temperature_vitrification = 80
-activate_air_filtration = 0
-activate_chamber_temp_control = 0
-additional_cooling_fan_speed = 0
+max_fan_speed = 80
+min_fan_speed = 40
+;;;slow_down_min_speed = 10
+slowdown_below_layer_time = 8
+;;;filament_start_gcode = ;filament start gcode\n
+temperature = 240
+;;;temperature_vitrification = 80
+;;;activate_air_filtration = 0
+;;;activate_chamber_temp_control = 0
+;;;additional_cooling_fan_speed = 0
 chamber_temperature = 0
-complete_print_exhaust_fan_speed = 80
-cool_cds_fan_start_at_height = 0
-cool_special_cds_fan_speed = 0
+;;;complete_print_exhaust_fan_speed = 80
+;;;cool_cds_fan_start_at_height = 0
+;;;cool_special_cds_fan_speed = 0
 default_filament_colour = ""
-during_print_exhaust_fan_speed = 60
-enable_overhang_bridge_fan = 1
-enable_pressure_advance = 1
-enable_special_area_additional_cooling_fan = 0
-epoxy_resin_plate_temp = 0
-epoxy_resin_plate_temp_initial_layer = 0
+;;;during_print_exhaust_fan_speed = 60
+;;;enable_overhang_bridge_fan = 1
+;;;enable_pressure_advance = 1
+;;;enable_special_area_additional_cooling_fan = 0
+;;;epoxy_resin_plate_temp = 0
+;;;epoxy_resin_plate_temp_initial_layer = 0
 filament_cooling_final_speed = 3.4
 filament_cooling_initial_speed = 2.2
 filament_cooling_moves = 4
-filament_is_support = 0
+;;;filament_is_support = 0
 filament_load_time = 0
 filament_loading_speed = 28
 filament_loading_speed_start = 3
@@ -80,16 +80,16 @@ filament_notes = ""
 filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
 filament_retract_lift_above = 0
 filament_retract_lift_below = 0
-filament_retract_lift_enforce = All Surfaces
-filament_shrink = 100%
+;;;filament_retract_lift_enforce = All Surfaces
+;;;filament_shrink = 100%
 filament_toolchange_delay = 0
 filament_unload_time = 0
 filament_unloading_speed = 90
 filament_unloading_speed_start = 100
-material_flow_dependent_temperature = 1
-material_flow_temp_graph = [[3.0,230],[10.0,240],[20.0,250]]
-nozzle_temperature_range_high = 270
-nozzle_temperature_range_low = 220
-pressure_advance = 0.07
-required_nozzle_HRC = 0
-support_material_interface_fan_speed = -1
+;;;material_flow_dependent_temperature = 1
+;;;material_flow_temp_graph = [[3.0,230],[10.0,240],[20.0,250]]
+;;;nozzle_temperature_range_high = 270
+;;;nozzle_temperature_range_low = 220
+;;;pressure_advance = 0.07
+;;;required_nozzle_HRC = 0
+;;;support_material_interface_fan_speed = -1

print_config/prusa_slicer/materials/Hyper_PLA.ini

@@ -1,78 +1,78 @@
 [metadata]
 show_name = Hyper PLA
-material_type = pla
+filament_type = pla
 
 
 [settings]
 idle_temperature = 150
 first_layer_bed_temperature = 60
-cool_plate_temp = 50
-eng_plate_temp = 45
-hot_plate_temp = 50
-textured_plate_temp = 50
-cool_plate_temp_initial_layer = 50
-eng_plate_temp_initial_layer = 45
-hot_plate_temp_initial_layer = 50
-textured_plate_temp_initial_layer = 50
-overhang_fan_threshold = 50%
-overhang_fan_speed = 100
-slow_down_for_layer_cooling = 1
-close_fan_the_first_x_layers = 1
-filament_end_gcode = ;filament end gcode 
-filament_flow_ratio = 0.95
-reduce_fan_stop_start_freq = 1
-fan_cooling_layer_time = 100
+;;;cool_plate_temp = 50
+;;;eng_plate_temp = 45
+;;;hot_plate_temp = 50
+;;;textured_plate_temp = 50
+;;;cool_plate_temp_initial_layer = 50
+;;;eng_plate_temp_initial_layer = 45
+;;;hot_plate_temp_initial_layer = 50
+;;;textured_plate_temp_initial_layer = 50
+;;;overhang_fan_threshold = 50%
+;;;overhang_fan_speed = 100
+;;;slow_down_for_layer_cooling = 1
+;;;close_fan_the_first_x_layers = 1
+;;;filament_end_gcode = ;filament end gcode
+extrusion_multiplier = 0.95
+;;;reduce_fan_stop_start_freq = 1
+;;;fan_cooling_layer_time = 100
 filament_cost = 30
 filament_density = 1.24
-filament_deretraction_speed = nil
+filament_deretract_speed = nil
 filament_diameter = 1.75
 filament_max_volumetric_speed = 23
 filament_minimal_purge_on_wipe_tower = 15
-filament_retraction_minimum_travel = nil
+;;;filament_retraction_minimum_travel = nil
 filament_retract_before_wipe = nil
-filament_retract_when_changing_layer = nil
-filament_retraction_length = 1.2
-filament_z_hop = 0.2
-filament_z_hop_types = Slope Lift
+;;;filament_retract_when_changing_layer = nil
+filament_retract_length = 1.2
+;;;filament_z_hop = 0.2
+;;;filament_z_hop_types = Slope Lift
 filament_retract_restart_extra = 0
-filament_retraction_speed = 40
-filament_settings_id = 
+filament_retract_speed = 40
+;;;filament_settings_id = 
 filament_soluble = 0
 filament_type = PLA
-filament_vendor = Creality
+;;;filament_vendor = Creality
 filament_wipe = nil
-filament_wipe_distance = nil
-bed_type = Cool Plate
-nozzle_temperature_initial_layer = 190
+;;;filament_wipe_distance = nil
+;;;bed_type = Cool Plate
+first_layer_temperature = 190
 full_fan_speed_layer = 0
-fan_max_speed = 100
-fan_min_speed = 100
-slow_down_min_speed = 20
-slow_down_layer_time = 6
-filament_start_gcode = ;filament start gcode
-nozzle_temperature = 190
-temperature_vitrification = 100
+max_fan_speed = 100
+min_fan_speed = 100
+;;;slow_down_min_speed = 20
+slowdown_below_layer_time = 6
+;;;filament_start_gcode = ;filament start gcode
+temperature = 190
+;;;temperature_vitrification = 100
 ; filament_adhesiveness_category = 100
-nozzle_temperature_range_low = 190
-nozzle_temperature_range_high = 240
-additional_cooling_fan_speed = 0
-activate_air_filtration = 0
-activate_chamber_temp_control = 0
+;;;nozzle_temperature_range_low = 190
+;;;nozzle_temperature_range_high = 240
+;;;additional_cooling_fan_speed = 0
+;;;activate_air_filtration = 0
+;;;activate_chamber_temp_control = 0
 chamber_temperature = 0
-complete_print_exhaust_fan_speed = 80
-cool_cds_fan_start_at_height = 0
-cool_special_cds_fan_speed = 0
+;;;complete_print_exhaust_fan_speed = 80
+;;;cool_cds_fan_start_at_height = 0
+;;;cool_special_cds_fan_speed = 0
 default_filament_colour = ""
-during_print_exhaust_fan_speed = 60
-enable_overhang_bridge_fan = 1
-enable_pressure_advance = 0
-enable_special_area_additional_cooling_fan = 0
-epoxy_resin_plate_temp = 0
-epoxy_resin_plate_temp_initial_layer = 0
+;;;during_print_exhaust_fan_speed = 60
+;;;enable_overhang_bridge_fan = 1
+;;;enable_pressure_advance = 0
+;;;enable_special_area_additional_cooling_fan = 0
+;;;epoxy_resin_plate_temp = 0
+;;;epoxy_resin_plate_temp_initial_layer = 0
 filament_cooling_final_speed = 3.4
 filament_cooling_initial_speed = 2.2
 filament_cooling_moves = 4
-filament_is_support = 0
+;;;filament_is_support = 0
 filament_load_time = 0
 filament_loading_speed = 28
 filament_loading_speed_start = 3
@@ -83,14 +83,14 @@ filament_notes = ""
 filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
 filament_retract_lift_above = 0
 filament_retract_lift_below = 0
-filament_retract_lift_enforce = All Surfaces
-filament_shrink = 100%
+;;;filament_retract_lift_enforce = All Surfaces
+;;;filament_shrink = 100%
 filament_toolchange_delay = 0
 filament_unload_time = 0
 filament_unloading_speed = 90
 filament_unloading_speed_start = 100
-material_flow_dependent_temperature = 0
-material_flow_temp_graph = [[3.5,200],[7.0,240]]
-pressure_advance = 0.02
-required_nozzle_HRC = 0
-support_material_interface_fan_speed = -1
+;;;material_flow_dependent_temperature = 0
+;;;material_flow_temp_graph = [[3.5,200],[7.0,240]]
+;;;pressure_advance = 0.02
+;;;required_nozzle_HRC = 0
+;;;support_material_interface_fan_speed = -1

print_config/prusa_slicer/materials/Hyper_Stardust_PLA.ini

@@ -1,80 +1,80 @@
 [metadata]
 show_name = Hyper Stardust PLA
-material_type = pla
+filament_type = pla
 
 
 [settings]
 idle_temperature = 150
 first_layer_bed_temperature = 60
-cool_plate_temp = 50
-eng_plate_temp = 45
-hot_plate_temp = 50
-textured_plate_temp = 50
-cool_plate_temp_initial_layer = 50
-eng_plate_temp_initial_layer = 45
-hot_plate_temp_initial_layer = 50
-textured_plate_temp_initial_layer = 50
-overhang_fan_threshold = 50%
-overhang_fan_speed = 100
-slow_down_for_layer_cooling = 1
-close_fan_the_first_x_layers = 1
-filament_end_gcode = ;filament end gcode 
-filament_flow_ratio = 0.95
-reduce_fan_stop_start_freq = 1
-fan_cooling_layer_time = 100
+;;;cool_plate_temp = 50
+;;;eng_plate_temp = 45
+;;;hot_plate_temp = 50
+;;;textured_plate_temp = 50
+;;;cool_plate_temp_initial_layer = 50
+;;;eng_plate_temp_initial_layer = 45
+;;;hot_plate_temp_initial_layer = 50
+;;;textured_plate_temp_initial_layer = 50
+;;;overhang_fan_threshold = 50%
+;;;overhang_fan_speed = 100
+;;;slow_down_for_layer_cooling = 1
+;;;close_fan_the_first_x_layers = 1
+;;;filament_end_gcode = ;filament end gcode
+extrusion_multiplier = 0.95
+;;;reduce_fan_stop_start_freq = 1
+;;;fan_cooling_layer_time = 100
 filament_cost = 26.9
 filament_density = 1.24
-filament_deretraction_speed = 15
+filament_deretract_speed = 15
 filament_diameter = 1.75
 filament_max_volumetric_speed = 18
 filament_minimal_purge_on_wipe_tower = 15
-filament_retraction_minimum_travel = 2
+;;;filament_retraction_minimum_travel = 2
 filament_retract_before_wipe = nil
-filament_retract_when_changing_layer = nil
-filament_retraction_length = 2
-filament_z_hop = nil
-filament_z_hop_types = nil
+;;;filament_retract_when_changing_layer = nil
+filament_retract_length = 2
+;;;filament_z_hop = nil
+;;;filament_z_hop_types = nil
 filament_retract_restart_extra = nil
-filament_retraction_speed = 15
-filament_settings_id = 
+filament_retract_speed = 15
+;;;filament_settings_id = 
 filament_soluble = 0
 filament_type = PLA
-filament_vendor = Creality
+;;;filament_vendor = Creality
 filament_wipe = nil
-filament_wipe_distance = 3
-bed_type = Cool Plate
-nozzle_temperature_initial_layer = 220
+;;;filament_wipe_distance = 3
+;;;bed_type = Cool Plate
+first_layer_temperature = 220
 full_fan_speed_layer = 0
-fan_max_speed = 100
-fan_min_speed = 100
-slow_down_min_speed = 10
-slow_down_layer_time = 14
-filament_start_gcode = ;filament start gcode
-nozzle_temperature = 220
-temperature_vitrification = 60
+max_fan_speed = 100
+min_fan_speed = 100
+;;;slow_down_min_speed = 10
+slowdown_below_layer_time = 14
+;;;filament_start_gcode = ;filament start gcode
+temperature = 220
+;;;temperature_vitrification = 60
 ; filament_adhesiveness_category = 100
-nozzle_temperature_range_low = 190
-nozzle_temperature_range_high = 240
-additional_cooling_fan_speed = 0
-activate_air_filtration = 0
-activate_chamber_temp_control = 0
+;;;nozzle_temperature_range_low = 190
+;;;nozzle_temperature_range_high = 240
+;;;additional_cooling_fan_speed = 0
+;;;activate_air_filtration = 0
+;;;activate_chamber_temp_control = 0
 chamber_temperature = 0
-complete_print_exhaust_fan_speed = 80
-cool_cds_fan_start_at_height = 0.5
-cool_special_cds_fan_speed = 0
-customized_plate_temp = 50
-customized_plate_temp_initial_layer = 50
+;;;complete_print_exhaust_fan_speed = 80
+;;;cool_cds_fan_start_at_height = 0.5
+;;;cool_special_cds_fan_speed = 0
+;;;customized_plate_temp = 50
+;;;customized_plate_temp_initial_layer = 50
 default_filament_colour = ""
-during_print_exhaust_fan_speed = 60
-enable_overhang_bridge_fan = 1
-enable_pressure_advance = 1
-enable_special_area_additional_cooling_fan = 0
-epoxy_resin_plate_temp = 50
-epoxy_resin_plate_temp_initial_layer = 50
+;;;during_print_exhaust_fan_speed = 60
+;;;enable_overhang_bridge_fan = 1
+;;;enable_pressure_advance = 1
+;;;enable_special_area_additional_cooling_fan = 0
+;;;epoxy_resin_plate_temp = 50
+;;;epoxy_resin_plate_temp_initial_layer = 50
 filament_cooling_final_speed = 3.4
 filament_cooling_initial_speed = 2.2
 filament_cooling_moves = 4
-filament_is_support = 0
+;;;filament_is_support = 0
 filament_load_time = 0
 filament_loading_speed = 28
 filament_loading_speed_start = 3
@@ -85,15 +85,15 @@ filament_notes = ""
 filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
 filament_retract_lift_above = nil
 filament_retract_lift_below = nil
-filament_retract_lift_enforce = nil
-filament_shrink = 100%
+;;;filament_retract_lift_enforce = nil
+;;;filament_shrink = 100%
 filament_shrinkage_compensation_z = 100%
 filament_toolchange_delay = 0
 filament_unload_time = 0
 filament_unloading_speed = 90
 filament_unloading_speed_start = 100
-material_flow_dependent_temperature = 0
-material_flow_temp_graph = [[0.8,200],[1.0,200],[1.2,220]]
-pressure_advance = 0.04
-required_nozzle_HRC = 0
-support_material_interface_fan_speed = -1
+;;;material_flow_dependent_temperature = 0
+;;;material_flow_temp_graph = [[0.8,200],[1.0,200],[1.2,220]]
+;;;pressure_advance = 0.04
+;;;required_nozzle_HRC = 0
+;;;support_material_interface_fan_speed = -1

print_config/prusa_slicer/materials/Soleyin_Ultra_PLA.ini

@@ -1,80 +1,80 @@
 [metadata]
 show_name = Soleyin Ultra PLA
-material_type = pla
+filament_type = pla
 
 
 [settings]
 idle_temperature = 150
 first_layer_bed_temperature = 60
-cool_plate_temp = 50
-eng_plate_temp = 45
-hot_plate_temp = 50
-textured_plate_temp = 50
-cool_plate_temp_initial_layer = 50
-eng_plate_temp_initial_layer = 45
-hot_plate_temp_initial_layer = 50
-textured_plate_temp_initial_layer = 50
-overhang_fan_threshold = 50%
-overhang_fan_speed = 100
-slow_down_for_layer_cooling = 1
-close_fan_the_first_x_layers = 1
-filament_end_gcode = ;filament end gcode 
-filament_flow_ratio = 0.96
-reduce_fan_stop_start_freq = 1
-fan_cooling_layer_time = 100
+;;;cool_plate_temp = 50
+;;;eng_plate_temp = 45
+;;;hot_plate_temp = 50
+;;;textured_plate_temp = 50
+;;;cool_plate_temp_initial_layer = 50
+;;;eng_plate_temp_initial_layer = 45
+;;;hot_plate_temp_initial_layer = 50
+;;;textured_plate_temp_initial_layer = 50
+;;;overhang_fan_threshold = 50%
+;;;overhang_fan_speed = 100
+;;;slow_down_for_layer_cooling = 1
+;;;close_fan_the_first_x_layers = 1
+;;;filament_end_gcode = ;filament end gcode
+extrusion_multiplier = 0.96
+;;;reduce_fan_stop_start_freq = 1
+;;;fan_cooling_layer_time = 100
 filament_cost = 6
 filament_density = 1.25
-filament_deretraction_speed = 15
+filament_deretract_speed = 15
 filament_diameter = 1.75
 filament_max_volumetric_speed = 16
 filament_minimal_purge_on_wipe_tower = 15
-filament_retraction_minimum_travel = nil
+;;;filament_retraction_minimum_travel = nil
 filament_retract_before_wipe = 90%
-filament_retract_when_changing_layer = nil
-filament_retraction_length = nil
-filament_z_hop = nil
-filament_z_hop_types = nil
+;;;filament_retract_when_changing_layer = nil
+filament_retract_length = nil
+;;;filament_z_hop = nil
+;;;filament_z_hop_types = nil
 filament_retract_restart_extra = nil
-filament_retraction_speed = 15
-filament_settings_id = 
+filament_retract_speed = 15
+;;;filament_settings_id = 
 filament_soluble = 0
 filament_type = PLA
-filament_vendor = Creality
+;;;filament_vendor = Creality
 filament_wipe = nil
-filament_wipe_distance = nil
-bed_type = Cool Plate
-nozzle_temperature_initial_layer = 220
+;;;filament_wipe_distance = nil
+;;;bed_type = Cool Plate
+first_layer_temperature = 220
 full_fan_speed_layer = 0
-fan_max_speed = 100
-fan_min_speed = 100
-slow_down_min_speed = 20
-slow_down_layer_time = 12
-filament_start_gcode = ;filament start gcode
-nozzle_temperature = 220
-temperature_vitrification = 60
+max_fan_speed = 100
+min_fan_speed = 100
+;;;slow_down_min_speed = 20
+slowdown_below_layer_time = 12
+;;;filament_start_gcode = ;filament start gcode
+temperature = 220
+;;;temperature_vitrification = 60
 ; filament_adhesiveness_category = 100
-nozzle_temperature_range_low = 190
-nozzle_temperature_range_high = 240
-additional_cooling_fan_speed = 0
-activate_air_filtration = 0
-activate_chamber_temp_control = 0
+;;;nozzle_temperature_range_low = 190
+;;;nozzle_temperature_range_high = 240
+;;;additional_cooling_fan_speed = 0
+;;;activate_air_filtration = 0
+;;;activate_chamber_temp_control = 0
 chamber_temperature = 0
-complete_print_exhaust_fan_speed = 80
-cool_cds_fan_start_at_height = 0
-cool_special_cds_fan_speed = 0
-customized_plate_temp = 60
-customized_plate_temp_initial_layer = 60
+;;;complete_print_exhaust_fan_speed = 80
+;;;cool_cds_fan_start_at_height = 0
+;;;cool_special_cds_fan_speed = 0
+;;;customized_plate_temp = 60
+;;;customized_plate_temp_initial_layer = 60
 default_filament_colour = ""
-during_print_exhaust_fan_speed = 60
-enable_overhang_bridge_fan = 1
-enable_pressure_advance = 1
-enable_special_area_additional_cooling_fan = 0
-epoxy_resin_plate_temp = 60
-epoxy_resin_plate_temp_initial_layer = 60
+;;;during_print_exhaust_fan_speed = 60
+;;;enable_overhang_bridge_fan = 1
+;;;enable_pressure_advance = 1
+;;;enable_special_area_additional_cooling_fan = 0
+;;;epoxy_resin_plate_temp = 60
+;;;epoxy_resin_plate_temp_initial_layer = 60
 filament_cooling_final_speed = 3.4
 filament_cooling_initial_speed = 2.2
 filament_cooling_moves = 4
-filament_is_support = 0
+;;;filament_is_support = 0
 filament_load_time = 0
 filament_loading_speed = 28
 filament_loading_speed_start = 3
@@ -85,15 +85,15 @@ filament_notes = ""
 filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
 filament_retract_lift_above = nil
 filament_retract_lift_below = nil
-filament_retract_lift_enforce = nil
-filament_shrink = 100%
+;;;filament_retract_lift_enforce = nil
+;;;filament_shrink = 100%
 filament_shrinkage_compensation_z = 100%
 filament_toolchange_delay = 0
 filament_unload_time = 0
 filament_unloading_speed = 90
 filament_unloading_speed_start = 100
-material_flow_dependent_temperature = 0
-material_flow_temp_graph = [[1.0,200],[1.1,200],[1.2,220]]
-pressure_advance = 0.05
-required_nozzle_HRC = 0
-support_material_interface_fan_speed = -1
+;;;material_flow_dependent_temperature = 0
+;;;material_flow_temp_graph = [[1.0,200],[1.1,200],[1.2,220]]
+;;;pressure_advance = 0.05
+;;;required_nozzle_HRC = 0
+;;;support_material_interface_fan_speed = -1

print_config/prusa_slicer/printers/Ender3_V3_SE.ini

@@ -30,8 +30,8 @@ max_layer_height = 0.36
 min_layer_height = 0.08
 max_print_height = 250
 extruder_clearance_radius = 90
-extruder_clearance_height_to_rod = 47
-extruder_clearance_height_to_lid = 34
+;;;extruder_clearance_height_to_rod = 47
+;;;extruder_clearance_height_to_lid = 34
 nozzle_diameter = 0.4
 printer_variant = 0.4
 retract_before_travel = 1
@@ -39,8 +39,8 @@ retract_before_wipe = 100
 retract_layer_change = 1
 retract_length = 0.8
 retract_length_toolchange = 1
-z_hop = 0.4
-z_hop_types = Slope Lift
+retract_lift = 0.4
+;;;z_hop_types = Slope Lift
 retract_restart_extra = 0
 retract_restart_extra_toolchange = 0
 retract_speed = 30

print_config/prusa_slicer/quality/0.08mm_Extra_Fine.ini

@@ -3,214 +3,214 @@ show_name = 0.08mm Extra Fine Quality
 
 
 [settings]
-adaptive_layer_height = 0
-reduce_crossing_wall = 0
-bridge_flow = 0.8
+variable_layer_height = 0
+avoid_crossing_perimeters = 0
+bridge_flow_ratio = 0.8
 bridge_speed = 25
 brim_width = 5
-print_sequence = by layer
+complete_objects = 0
 default_acceleration = 2500
-bridge_no_support = 0
+dont_support_bridges = 0
 elefant_foot_compensation = 0.15
-outer_wall_line_width = 0.42
-outer_wall_speed = 60
-line_width = 0.46
-infill_direction = 45
-sparse_infill_density = 10%
-sparse_infill_pattern = zig-zag
-initial_layer_line_width = 0.46
-initial_layer_print_height = 0.2
-initial_layer_speed = 60
-gap_infill_speed = 50
-infill_combination = 0
-sparse_infill_line_width = 0.45
-infill_wall_overlap = 15%
-sparse_infill_speed = 180
+external_perimeter_extrusion_width = 0.42
+external_perimeter_speed = 60
+extrusion_width = 0.46
+fill_angle = 45
+fill_density = 10%
+fill_pattern = zigzag
+first_layer_extrusion_width = 0.46
+first_layer_height = 0.2
+first_layer_speed = 60
+gap_fill_speed = 50
+solid_infill_every_layers = 0
+infill_extrusion_width = 0.45
+infill_overlap = 15%
+infill_speed = 180
 interface_shells = 0
-detect_overhang_wall = 1
-reduce_infill_retraction = 1
-wall_loops = 2
-inner_wall_line_width = 0.45
-inner_wall_speed = 90
-print_settings_id = 
+;;;detect_overhang_wall = 1
+;;;reduce_infill_retraction = 1
+perimeters = 2
+perimeter_extrusion_width = 0.45
+perimeter_speed = 90
+;;;print_settings_id = 
 raft_layers = 0
 seam_position = aligned
 skirt_distance = 2
 skirt_height = 2
-minimum_sparse_infill_area = 10
-internal_solid_infill_line_width = 0.42
-internal_solid_infill_speed = 180
-spiral_mode = 0
+solid_infill_below_area = 10
+solid_infill_extrusion_width = 0.42
+solid_infill_speed = 180
+spiral_vase = 0
 standby_temperature_delta = -5
-detect_thin_wall = 1
-top_surface_line_width = 0.42
-top_surface_speed = 50
+thin_walls = 1
+top_infill_extrusion_width = 0.42
+top_solid_infill_speed = 50
 travel_speed = 150
-enable_prime_tower = 0
-prime_tower_width = 60
-xy_hole_compensation = 0
-xy_contour_compensation = 0
-max_travel_detour_distance = 0
-bottom_surface_pattern = monotonic
-bottom_shell_layers = 7
-bottom_shell_thickness = 0
-brim_object_gap = 0.1
-compatible_printers_condition = 
-top_surface_acceleration = 2500
+wipe_tower = 0
+wipe_tower_width = 60
+xy_size_compensation = 0
+;;;xy_contour_compensation = 0
+;;;max_travel_detour_distance = 0
+bottom_fill_pattern = monotonic
+bottom_solid_layers = 7
+bottom_solid_min_thickness = 0
+;;;brim_object_gap = 0.1
+;;;compatible_printers_condition = 
+top_solid_infill_acceleration = 2500
 draft_shield = disabled
-enable_arc_fitting = 0
-wall_infill_order = inner wall/outer wall/infill
-initial_layer_acceleration = 500
+arc_fitting = disabled
+;;;wall_infill_order = inner wall/outer wall/infill
+first_layer_acceleration = 500
 travel_acceleration = 2500
-inner_wall_acceleration = 2000
-ironing_flow = 15%
+perimeter_acceleration = 2000
+ironing_flowrate = 15%
 ironing_spacing = 0.1
 ironing_speed = 20
 ironing_type = top
 layer_height = 0.08
-overhang_1_4_speed = 0
-overhang_2_4_speed = 20
-overhang_3_4_speed = 15
-overhang_4_4_speed = 10
-skirt_loops = 0
+overhang_speed_0 = 0
+overhang_speed_1 = 20
+overhang_speed_2 = 15
+overhang_speed_3 = 10
+skirts = 2
 resolution = 0.012
-top_surface_pattern = monotonicline
-top_shell_layers = 9
-top_shell_thickness = 0.8
-initial_layer_infill_speed = 80
+top_fill_pattern = monotonicline
+top_solid_layers = 9
+top_solid_min_thickness = 0.8
+first_layer_infill_speed = 80
 wipe_tower_no_sparse_layers = 0
-accel_to_decel_enable = 1
-accel_to_decel_factor = 50%
-acceleration_limit_mess = [[0.5,1.0,100,6000],[1.0,1.5,80,5500],[1.5,2.0,60,5000]]
-acceleration_limit_mess_enable = 0
-alternate_extra_wall = 0
-bottom_solid_infill_flow_ratio = 1
+;;;accel_to_decel_enable = 1
+;;;accel_to_decel_factor = 50%
+;;;acceleration_limit_mess = [[0.5,1.0,100,6000],[1.0,1.5,80,5500],[1.5,2.0,60,5000]]
+;;;acceleration_limit_mess_enable = 0
+;;;alternate_extra_wall = 0
+;;;bottom_solid_infill_flow_ratio = 1
 bridge_acceleration = 50%
 bridge_angle = 0
-bridge_density = 100%
-brim_ears_detection_length = 1
-brim_ears_max_angle = 125
+;;;bridge_density = 100%
+;;;brim_ears_detection_length = 1
+;;;brim_ears_max_angle = 125
 brim_type = no_brim
-default_jerk = 8
-detect_narrow_internal_solid_infill = 1
-elefant_foot_compensation_layers = 1
-enable_overhang_speed = 1
-enforce_support_layers = 0
+;;;default_jerk = 8
+;;;detect_narrow_internal_solid_infill = 1
+;;;elefant_foot_compensation_layers = 1
+enable_dynamic_overhang_speeds = 1
+support_material_enforce_layers = 0
 ensure_vertical_shell_thickness = ensure_all
-exclude_object = 0
+;;;exclude_object = 0
 extra_perimeters_on_overhangs = 0
-filter_out_gap_fill = 0
-flush_into_infill = 0
-flush_into_objects = 0
-flush_into_support = 1
+;;;filter_out_gap_fill = 0
+;;;flush_into_infill = 0
+;;;flush_into_objects = 0
+;;;flush_into_support = 1
 fuzzy_skin = none
-fuzzy_skin_first_layer = 0
-fuzzy_skin_point_distance = 0.8
+;;;fuzzy_skin_first_layer = 0
+fuzzy_skin_point_dist = 0.8
 fuzzy_skin_thickness = 0.3
-gcode_add_line_number = 0
+;;;gcode_add_line_number = 0
 gcode_comments = 0
 gcode_label_objects = 1
-hole_to_polyhole = 0
-hole_to_polyhole_threshold = 0.01
-hole_to_polyhole_twisted = 1
-independent_support_layer_height = 1
+;;;hole_to_polyhole = 0
+;;;hole_to_polyhole_threshold = 0.01
+;;;hole_to_polyhole_twisted = 1
+;;;independent_support_layer_height = 1
 infill_anchor = 400%
 infill_anchor_max = 20
-infill_jerk = 20
-initial_layer_jerk = 8
-initial_layer_min_bead_width = 85%
-initial_layer_travel_speed = 100%
-inner_wall_jerk = 20
-internal_bridge_flow = 1
-internal_bridge_speed = 150%
-internal_solid_infill_acceleration = 100%
-internal_solid_infill_pattern = monotonic
-ironing_angle = -1
-ironing_pattern = zig-zag
-ironing_support_layer = 0
-is_infill_first = 0
-make_overhang_printable = 0
-make_overhang_printable_angle = 55
-make_overhang_printable_hole_size = 0
-max_bridge_length = 10
-max_volumetric_extrusion_rate_slope = 0
-max_volumetric_extrusion_rate_slope_segment_length = 3
+;;;infill_jerk = 20
+;;;initial_layer_jerk = 8
+;;;initial_layer_min_bead_width = 85%
+;;;initial_layer_travel_speed = 100%
+;;;inner_wall_jerk = 20
+;;;internal_bridge_flow = 1
+;;;internal_bridge_speed = 150%
+solid_infill_acceleration = 100%
+solid_fill_pattern = monotonic
+;;;ironing_angle = -1
+;;;ironing_pattern = zigzag
+;;;ironing_support_layer = 0
+infill_first = 0
+;;;make_overhang_printable = 0
+;;;make_overhang_printable_angle = 55
+;;;make_overhang_printable_hole_size = 0
+;;;max_bridge_length = 10
+;;;max_volumetric_extrusion_rate_slope = 0
+;;;max_volumetric_extrusion_rate_slope_segment_length = 3
 min_bead_width = 85%
 min_feature_size = 25%
-min_width_top_surface = 300%
-minimum_support_area = 5
+;;;min_width_top_surface = 300%
+;;;minimum_support_area = 5
 mmu_segmented_region_interlocking_depth = 0
 mmu_segmented_region_max_width = 0
-only_one_wall_first_layer = 0
-only_one_wall_top = 0
+;;;only_one_wall_first_layer = 0
+top_one_perimeter_type = none
 ooze_prevention = 0
-outer_wall_acceleration = 1000
-outer_wall_jerk = 20
-overhang_reverse = 0
-overhang_reverse_internal_only = 0
-overhang_reverse_threshold = 50%
-overhang_speed_classic = 0
-precise_outer_wall = 0
-prime_tower_brim_width = 3
-prime_tower_enhance_type = chamfer
-prime_volume = 45
-print_flow_ratio = 1
-print_order = default
+external_perimeter_acceleration = 1000
+;;;outer_wall_jerk = 20
+;;;overhang_reverse = 0
+;;;overhang_reverse_internal_only = 0
+;;;overhang_reverse_threshold = 50%
+;;;overhang_speed_classic = 0
+;;;precise_outer_wall = 0
+wipe_tower_brim_width = 3
+;;;prime_tower_enhance_type = chamfer
+;;;prime_volume = 45
+;;;print_flow_ratio = 1
+;;;print_order = default
 raft_contact_distance = 0.1
 raft_expansion = 1.5
 raft_first_layer_density = 90%
 raft_first_layer_expansion = 2
-role_based_wipe_speed = 1
-scarf_angle_threshold = 155
-scarf_joint_flow_ratio = 1
-scarf_joint_speed = 100%
-scarf_overhang_threshold = 40%
-seam_gap = 10%
-seam_slope_conditional = 0
-seam_slope_entire_loop = 0
-seam_slope_inner_walls = 0
-seam_slope_min_length = 20
-seam_slope_start_height = 0
-seam_slope_steps = 10
-seam_slope_type = none
+;;;role_based_wipe_speed = 1
+;;;scarf_angle_threshold = 155
+;;;scarf_joint_flow_ratio = 1
+;;;scarf_joint_speed = 100%
+;;;scarf_overhang_threshold = 40%
+seam_gap_distance = 10%
+;;;seam_slope_conditional = 0
+scarf_seam_entire_loop = 0
+scarf_seam_on_inner_perimeters = 0
+scarf_seam_length = 20
+scarf_seam_start_height = 0
+;;;seam_slope_steps = 10
+;;;seam_slope_type = none
 single_extruder_multi_material_priming = 0
-skirt_speed = 50
+;;;skirt_speed = 50
 slice_closing_radius = 0.049
 slicing_mode = regular
-slow_down_layers = 0
-slowdown_for_curled_perimeters = 0
-small_area_infill_flow_compensation = 0
-small_area_infill_flow_compensation_model = 0,0;\n0.2,0.4444;\n0.4,0.6145;\n0.6,0.7059;\n0.8,0.7619;\n1.5,0.8571;\n2,0.8889;\n3,0.9231;\n5,0.9520;\n10,1
+;;;slow_down_layers = 0
+avoid_crossing_curled_overhangs = 0
+;;;small_area_infill_flow_compensation = 0
+;;;small_area_infill_flow_compensation_model = 0,0;\n0.2,0.4444;\n0.4,0.6145;\n0.6,0.7059;\n0.8,0.7619;\n1.5,0.8571;\n2,0.8889;\n3,0.9231;\n5,0.9520;\n10,1
 small_perimeter_speed = 50%
-small_perimeter_threshold = 0
-solid_infill_filament = 1
-sparse_infill_acceleration = 100%
-sparse_infill_filament = 1
-speed_limit_to_height = [[100,150,200,6000],[150,200,200,4000],[200,250,200,2000]]
-speed_limit_to_height_enable = 0
-spiral_mode_max_xy_smoothing = 200%
-spiral_mode_smooth = 0
+;;;small_perimeter_threshold = 0
+;;;solid_infill_filament = 1
+infill_acceleration = 100%
+;;;sparse_infill_filament = 1
+;;;speed_limit_to_height = [[100,150,200,6000],[150,200,200,4000],[200,250,200,2000]]
+;;;speed_limit_to_height_enable = 0
+;;;spiral_mode_max_xy_smoothing = 200%
+;;;spiral_mode_smooth = 0
 staggered_inner_seams = 1
 thick_bridges = 0
-thick_internal_bridges = 1
-timelapse_type = 0
-top_solid_infill_flow_ratio = 1
-top_surface_jerk = 9
-travel_jerk = 12
+;;;thick_internal_bridges = 1
+;;;timelapse_type = 0
+;;;top_solid_infill_flow_ratio = 1
+;;;top_surface_jerk = 9
+;;;travel_jerk = 12
 travel_speed_z = 0
-wall_direction = auto
+;;;wall_direction = auto
 wall_distribution_count = 1
-wall_filament = 1
-wall_generator = arachne
-wall_sequence = inner wall/outer wall
+;;;wall_filament = 1
+perimeter_generator = arachne
+;;;wall_sequence = inner wall/outer wall
 wall_transition_angle = 10
 wall_transition_filter_deviation = 25%
 wall_transition_length = 100%
-wipe_before_external_loop = 0
-wipe_on_loops = 0
-wipe_speed = 80%
+;;;wipe_before_external_loop = 0
+;;;wipe_on_loops = 0
+;;;wipe_speed = 80%
 wipe_tower_bridging = 10
 wipe_tower_cone_angle = 0
 wipe_tower_extra_spacing = 100%
-wipe_tower_rotation_angle = 0
-wiping_volumes_extruders = 70,70,70,70,70,70,70,70,70,70
+;;;wipe_tower_rotation_angle = 0
+;;;wiping_volumes_extruders = 70,70,70,70,70,70,70,70,70,70

print_config/prusa_slicer/quality/0.12mm_Fine.ini

@@ -3,198 +3,198 @@ show_name = 0.12mm Fine Quality
 
 
 [settings]
-adaptive_layer_height = 0
-reduce_crossing_wall = 0
-bridge_flow = 0.95
+variable_layer_height = 0
+avoid_crossing_perimeters = 0
+bridge_flow_ratio = 0.95
 bridge_speed = 100
 brim_width = 5
-print_sequence = by layer
+complete_objects = 0
 default_acceleration = 2500
-bridge_no_support = 0
+dont_support_bridges = 0
 elefant_foot_compensation = 0
-outer_wall_line_width = 0.42
-outer_wall_speed = 60
-line_width = 0.46
-infill_direction = 45
-sparse_infill_density = 15%
-sparse_infill_pattern = grid
-initial_layer_line_width = 0.46
-initial_layer_print_height = 0.2
-initial_layer_speed = 30
-gap_infill_speed = 50
-infill_combination = 0
-sparse_infill_line_width = 0.45
-infill_wall_overlap = 15%
-sparse_infill_speed = 180
+external_perimeter_extrusion_width = 0.42
+external_perimeter_speed = 60
+extrusion_width = 0.46
+fill_angle = 45
+fill_density = 15%
+fill_pattern = grid
+first_layer_extrusion_width = 0.46
+first_layer_height = 0.2
+first_layer_speed = 30
+gap_fill_speed = 50
+solid_infill_every_layers = 0
+infill_extrusion_width = 0.45
+infill_overlap = 15%
+infill_speed = 180
 interface_shells = 0
-detect_overhang_wall = 1
-reduce_infill_retraction = 1
-wall_loops = 2
-inner_wall_line_width = 0.45
-inner_wall_speed = 90
-print_settings_id = 
+;;;detect_overhang_wall = 1
+;;;reduce_infill_retraction = 1
+perimeters = 2
+perimeter_extrusion_width = 0.45
+perimeter_speed = 90
+;;;print_settings_id = 
 raft_layers = 0
 seam_position = aligned
 skirt_distance = 2
 skirt_height = 2
-minimum_sparse_infill_area = 10
-internal_solid_infill_line_width = 0.42
-internal_solid_infill_speed = 180
-spiral_mode = 0
+solid_infill_below_area = 10
+solid_infill_extrusion_width = 0.42
+solid_infill_speed = 180
+spiral_vase = 0
 standby_temperature_delta = -5
-detect_thin_wall = 1
-top_surface_line_width = 0.42
-top_surface_speed = 50
+thin_walls = 1
+top_infill_extrusion_width = 0.42
+top_solid_infill_speed = 50
 travel_speed = 150
-enable_prime_tower = 0
-prime_tower_width = 60
-xy_hole_compensation = 0
-xy_contour_compensation = 0
-max_travel_detour_distance = 0
-bottom_surface_pattern = monotonic
-bottom_shell_layers = 5
-bottom_shell_thickness = 0
-brim_object_gap = 0.1
-compatible_printers_condition = 
-top_surface_acceleration = 2500
+wipe_tower = 0
+wipe_tower_width = 60
+xy_size_compensation = 0
+;;;xy_contour_compensation = 0
+;;;max_travel_detour_distance = 0
+bottom_fill_pattern = monotonic
+bottom_solid_layers = 5
+bottom_solid_min_thickness = 0
+;;;brim_object_gap = 0.1
+;;;compatible_printers_condition = 
+top_solid_infill_acceleration = 2500
 draft_shield = disabled
-enable_arc_fitting = 0
-wall_infill_order = inner wall/outer wall/infill
-initial_layer_acceleration = 500
+arc_fitting = disabled
+;;;wall_infill_order = inner wall/outer wall/infill
+first_layer_acceleration = 500
 travel_acceleration = 2500
-inner_wall_acceleration = 2000
-ironing_flow = 15%
+perimeter_acceleration = 2000
+ironing_flowrate = 15%
 ironing_spacing = 0.1
 ironing_speed = 20
 ironing_type = top
 layer_height = 0.12
-overhang_1_4_speed = 0
-overhang_2_4_speed = 20
-overhang_3_4_speed = 15
-overhang_4_4_speed = 10
-skirt_loops = 0
+overhang_speed_0 = 0
+overhang_speed_1 = 20
+overhang_speed_2 = 15
+overhang_speed_3 = 10
+skirts = 2
 resolution = 0.012
-top_surface_pattern = monotonic
-top_shell_layers = 5
-top_shell_thickness = 0.8
-initial_layer_infill_speed = 80
+top_fill_pattern = monotonic
+top_solid_layers = 5
+top_solid_min_thickness = 0.8
+first_layer_infill_speed = 80
 wipe_tower_no_sparse_layers = 0
-accel_to_decel_enable = 1
-accel_to_decel_factor = 50%
-acceleration_limit_mess = [[0.5,1.0,100,6000],[1.0,1.5,80,5500],[1.5,2.0,60,5000]]
-acceleration_limit_mess_enable = 0
-alternate_extra_wall = 0
-bottom_solid_infill_flow_ratio = 1
+;;;accel_to_decel_enable = 1
+;;;accel_to_decel_factor = 50%
+;;;acceleration_limit_mess = [[0.5,1.0,100,6000],[1.0,1.5,80,5500],[1.5,2.0,60,5000]]
+;;;acceleration_limit_mess_enable = 0
+;;;alternate_extra_wall = 0
+;;;bottom_solid_infill_flow_ratio = 1
 bridge_acceleration = 50%
 bridge_angle = 0
-bridge_density = 100%
-brim_ears_detection_length = 1
-brim_ears_max_angle = 125
+;;;bridge_density = 100%
+;;;brim_ears_detection_length = 1
+;;;brim_ears_max_angle = 125
 brim_type = no_brim
-default_jerk = 8
-detect_narrow_internal_solid_infill = 1
-elefant_foot_compensation_layers = 1
-enable_overhang_speed = 1
-enforce_support_layers = 0
+;;;default_jerk = 8
+;;;detect_narrow_internal_solid_infill = 1
+;;;elefant_foot_compensation_layers = 1
+enable_dynamic_overhang_speeds = 1
+support_material_enforce_layers = 0
 ensure_vertical_shell_thickness = ensure_all
-exclude_object = 0
+;;;exclude_object = 0
 extra_perimeters_on_overhangs = 0
-filter_out_gap_fill = 0
-flush_into_infill = 0
-flush_into_objects = 0
-flush_into_support = 1
+;;;filter_out_gap_fill = 0
+;;;flush_into_infill = 0
+;;;flush_into_objects = 0
+;;;flush_into_support = 1
 fuzzy_skin = none
-fuzzy_skin_first_layer = 0
-fuzzy_skin_point_distance = 0.8
+;;;fuzzy_skin_first_layer = 0
+fuzzy_skin_point_dist = 0.8
 fuzzy_skin_thickness = 0.3
-gcode_add_line_number = 0
+;;;gcode_add_line_number = 0
 gcode_comments = 0
 gcode_label_objects = 1
-hole_to_polyhole = 0
-hole_to_polyhole_threshold = 0.01
-hole_to_polyhole_twisted = 1
-independent_support_layer_height = 1
+;;;hole_to_polyhole = 0
+;;;hole_to_polyhole_threshold = 0.01
+;;;hole_to_polyhole_twisted = 1
+;;;independent_support_layer_height = 1
 infill_anchor = 400%
 infill_anchor_max = 20
-infill_jerk = 20
-initial_layer_jerk = 8
-initial_layer_min_bead_width = 85%
-initial_layer_travel_speed = 100%
-inner_wall_jerk = 20
-internal_bridge_flow = 1
-internal_bridge_speed = 150%
-internal_solid_infill_acceleration = 100%
-internal_solid_infill_pattern = monotonic
-ironing_angle = -1
-ironing_pattern = zig-zag
-ironing_support_layer = 0
-is_infill_first = 0
-make_overhang_printable = 0
-make_overhang_printable_angle = 55
-make_overhang_printable_hole_size = 0
-max_bridge_length = 10
-max_volumetric_extrusion_rate_slope = 0
-max_volumetric_extrusion_rate_slope_segment_length = 3
+;;;infill_jerk = 20
+;;;initial_layer_jerk = 8
+;;;initial_layer_min_bead_width = 85%
+;;;initial_layer_travel_speed = 100%
+;;;inner_wall_jerk = 20
+;;;internal_bridge_flow = 1
+;;;internal_bridge_speed = 150%
+solid_infill_acceleration = 100%
+solid_fill_pattern = monotonic
+;;;ironing_angle = -1
+;;;ironing_pattern = zigzag
+;;;ironing_support_layer = 0
+infill_first = 0
+;;;make_overhang_printable = 0
+;;;make_overhang_printable_angle = 55
+;;;make_overhang_printable_hole_size = 0
+;;;max_bridge_length = 10
+;;;max_volumetric_extrusion_rate_slope = 0
+;;;max_volumetric_extrusion_rate_slope_segment_length = 3
 min_bead_width = 85%
 min_feature_size = 25%
-min_width_top_surface = 300%
-minimum_support_area = 5
+;;;min_width_top_surface = 300%
+;;;minimum_support_area = 5
 mmu_segmented_region_interlocking_depth = 0
 mmu_segmented_region_max_width = 0
-only_one_wall_first_layer = 0
-only_one_wall_top = 0
+;;;only_one_wall_first_layer = 0
+top_one_perimeter_type = none
 ooze_prevention = 0
-outer_wall_acceleration = 1000
-outer_wall_jerk = 20
-overhang_reverse = 0
-overhang_reverse_internal_only = 0
-overhang_reverse_threshold = 50%
-overhang_speed_classic = 0
-precise_outer_wall = 0
-prime_tower_brim_width = 3
-prime_volume = 45
-print_flow_ratio = 1
+external_perimeter_acceleration = 1000
+;;;outer_wall_jerk = 20
+;;;overhang_reverse = 0
+;;;overhang_reverse_internal_only = 0
+;;;overhang_reverse_threshold = 50%
+;;;overhang_speed_classic = 0
+;;;precise_outer_wall = 0
+wipe_tower_brim_width = 3
+;;;prime_volume = 45
+;;;print_flow_ratio = 1
 raft_contact_distance = 0.1
 raft_expansion = 1.5
 raft_first_layer_density = 90%
 raft_first_layer_expansion = 2
-role_based_wipe_speed = 1
-seam_gap = 10%
+;;;role_based_wipe_speed = 1
+seam_gap_distance = 10%
 single_extruder_multi_material_priming = 0
-skirt_speed = 50
+;;;skirt_speed = 50
 slice_closing_radius = 0.049
 slicing_mode = regular
-slow_down_layers = 0
-slowdown_for_curled_perimeters = 0
+;;;slow_down_layers = 0
+avoid_crossing_curled_overhangs = 0
 small_perimeter_speed = 50%
-small_perimeter_threshold = 0
-solid_infill_filament = 1
-sparse_infill_acceleration = 100%
-sparse_infill_filament = 1
-speed_limit_to_height = [[100,150,100,6000],[150,200,80,5500],[200,250,60,5000]]
-speed_limit_to_height_enable = 0
-spiral_mode_max_xy_smoothing = 200%
-spiral_mode_smooth = 0
+;;;small_perimeter_threshold = 0
+;;;solid_infill_filament = 1
+infill_acceleration = 100%
+;;;sparse_infill_filament = 1
+;;;speed_limit_to_height = [[100,150,100,6000],[150,200,80,5500],[200,250,60,5000]]
+;;;speed_limit_to_height_enable = 0
+;;;spiral_mode_max_xy_smoothing = 200%
+;;;spiral_mode_smooth = 0
 staggered_inner_seams = 0
 thick_bridges = 0
-thick_internal_bridges = 1
-timelapse_type = 0
-top_solid_infill_flow_ratio = 1
-top_surface_jerk = 20
-travel_jerk = 8
+;;;thick_internal_bridges = 1
+;;;timelapse_type = 0
+;;;top_solid_infill_flow_ratio = 1
+;;;top_surface_jerk = 20
+;;;travel_jerk = 8
 travel_speed_z = 0
 wall_distribution_count = 1
-wall_filament = 1
-wall_generator = arachne
-wall_sequence = inner wall/outer wall
+;;;wall_filament = 1
+perimeter_generator = arachne
+;;;wall_sequence = inner wall/outer wall
 wall_transition_angle = 10
 wall_transition_filter_deviation = 25%
 wall_transition_length = 100%
-wipe_before_external_loop = 0
-wipe_on_loops = 0
-wipe_speed = 80%
+;;;wipe_before_external_loop = 0
+;;;wipe_on_loops = 0
+;;;wipe_speed = 80%
 wipe_tower_bridging = 10
 wipe_tower_cone_angle = 0
 wipe_tower_extra_spacing = 100%
-wipe_tower_rotation_angle = 0
-wiping_volumes_extruders = 70,70,70,70,70,70,70,70,70,70
+;;;wipe_tower_rotation_angle = 0
+;;;wiping_volumes_extruders = 70,70,70,70,70,70,70,70,70,70

print_config/prusa_slicer/quality/0.16mm_Optimal.ini

@@ -3,198 +3,198 @@ show_name = 0.16mm Optimal Quality
 
 
 [settings]
-adaptive_layer_height = 0
-reduce_crossing_wall = 0
-bridge_flow = 0.95
+variable_layer_height = 0
+avoid_crossing_perimeters = 0
+bridge_flow_ratio = 0.95
 bridge_speed = 100
 brim_width = 5
-print_sequence = by layer
+complete_objects = 0
 default_acceleration = 2500
-bridge_no_support = 0
+dont_support_bridges = 0
 elefant_foot_compensation = 0
-outer_wall_line_width = 0.42
-outer_wall_speed = 60
-line_width = 0.46
-infill_direction = 45
-sparse_infill_density = 15%
-sparse_infill_pattern = grid
-initial_layer_line_width = 0.46
-initial_layer_print_height = 0.2
-initial_layer_speed = 30
-gap_infill_speed = 50
-infill_combination = 0
-sparse_infill_line_width = 0.45
-infill_wall_overlap = 15%
-sparse_infill_speed = 180
+external_perimeter_extrusion_width = 0.42
+external_perimeter_speed = 60
+extrusion_width = 0.46
+fill_angle = 45
+fill_density = 15%
+fill_pattern = grid
+first_layer_extrusion_width = 0.46
+first_layer_height = 0.2
+first_layer_speed = 30
+gap_fill_speed = 50
+solid_infill_every_layers = 0
+infill_extrusion_width = 0.45
+infill_overlap = 15%
+infill_speed = 180
 interface_shells = 0
-detect_overhang_wall = 1
-reduce_infill_retraction = 1
-wall_loops = 2
-inner_wall_line_width = 0.45
-inner_wall_speed = 90
-print_settings_id = 
+;;;detect_overhang_wall = 1
+;;;reduce_infill_retraction = 1
+perimeters = 2
+perimeter_extrusion_width = 0.45
+perimeter_speed = 90
+;;;print_settings_id = 
 raft_layers = 0
 seam_position = aligned
 skirt_distance = 2
 skirt_height = 2
-minimum_sparse_infill_area = 10
-internal_solid_infill_line_width = 0.42
-internal_solid_infill_speed = 180
-spiral_mode = 0
+solid_infill_below_area = 10
+solid_infill_extrusion_width = 0.42
+solid_infill_speed = 180
+spiral_vase = 0
 standby_temperature_delta = -5
-detect_thin_wall = 1
-top_surface_line_width = 0.42
-top_surface_speed = 50
+thin_walls = 1
+top_infill_extrusion_width = 0.42
+top_solid_infill_speed = 50
 travel_speed = 150
-enable_prime_tower = 0
-prime_tower_width = 60
-xy_hole_compensation = 0
-xy_contour_compensation = 0
-max_travel_detour_distance = 0
-bottom_surface_pattern = monotonic
-bottom_shell_layers = 4
-bottom_shell_thickness = 0
-brim_object_gap = 0.1
-compatible_printers_condition = 
-top_surface_acceleration = 2500
+wipe_tower = 0
+wipe_tower_width = 60
+xy_size_compensation = 0
+;;;xy_contour_compensation = 0
+;;;max_travel_detour_distance = 0
+bottom_fill_pattern = monotonic
+bottom_solid_layers = 4
+bottom_solid_min_thickness = 0
+;;;brim_object_gap = 0.1
+;;;compatible_printers_condition = 
+top_solid_infill_acceleration = 2500
 draft_shield = disabled
-enable_arc_fitting = 0
-wall_infill_order = inner wall/outer wall/infill
-initial_layer_acceleration = 500
+arc_fitting = disabled
+;;;wall_infill_order = inner wall/outer wall/infill
+first_layer_acceleration = 500
 travel_acceleration = 2500
-inner_wall_acceleration = 2000
-ironing_flow = 15%
+perimeter_acceleration = 2000
+ironing_flowrate = 15%
 ironing_spacing = 0.1
 ironing_speed = 20
 ironing_type = top
 layer_height = 0.16
-overhang_1_4_speed = 0
-overhang_2_4_speed = 20
-overhang_3_4_speed = 15
-overhang_4_4_speed = 10
-skirt_loops = 0
+overhang_speed_0 = 0
+overhang_speed_1 = 20
+overhang_speed_2 = 15
+overhang_speed_3 = 10
+skirts = 2
 resolution = 0.012
-top_surface_pattern = monotonic
-top_shell_layers = 6
-top_shell_thickness = 0.8
-initial_layer_infill_speed = 80
+top_fill_pattern = monotonic
+top_solid_layers = 6
+top_solid_min_thickness = 0.8
+first_layer_infill_speed = 80
 wipe_tower_no_sparse_layers = 0
-accel_to_decel_enable = 1
-accel_to_decel_factor = 50%
-acceleration_limit_mess = [[0.5,1.0,100,6000],[1.0,1.5,80,5500],[1.5,2.0,60,5000]]
-acceleration_limit_mess_enable = 0
-alternate_extra_wall = 0
-bottom_solid_infill_flow_ratio = 1
+;;;accel_to_decel_enable = 1
+;;;accel_to_decel_factor = 50%
+;;;acceleration_limit_mess = [[0.5,1.0,100,6000],[1.0,1.5,80,5500],[1.5,2.0,60,5000]]
+;;;acceleration_limit_mess_enable = 0
+;;;alternate_extra_wall = 0
+;;;bottom_solid_infill_flow_ratio = 1
 bridge_acceleration = 50%
 bridge_angle = 0
-bridge_density = 100%
-brim_ears_detection_length = 1
-brim_ears_max_angle = 125
+;;;bridge_density = 100%
+;;;brim_ears_detection_length = 1
+;;;brim_ears_max_angle = 125
 brim_type = no_brim
-default_jerk = 8
-detect_narrow_internal_solid_infill = 1
-elefant_foot_compensation_layers = 1
-enable_overhang_speed = 1
-enforce_support_layers = 0
+;;;default_jerk = 8
+;;;detect_narrow_internal_solid_infill = 1
+;;;elefant_foot_compensation_layers = 1
+enable_dynamic_overhang_speeds = 1
+support_material_enforce_layers = 0
 ensure_vertical_shell_thickness = ensure_all
-exclude_object = 0
+;;;exclude_object = 0
 extra_perimeters_on_overhangs = 0
-filter_out_gap_fill = 0
-flush_into_infill = 0
-flush_into_objects = 0
-flush_into_support = 1
+;;;filter_out_gap_fill = 0
+;;;flush_into_infill = 0
+;;;flush_into_objects = 0
+;;;flush_into_support = 1
 fuzzy_skin = none
-fuzzy_skin_first_layer = 0
-fuzzy_skin_point_distance = 0.8
+;;;fuzzy_skin_first_layer = 0
+fuzzy_skin_point_dist = 0.8
 fuzzy_skin_thickness = 0.3
-gcode_add_line_number = 0
+;;;gcode_add_line_number = 0
 gcode_comments = 0
 gcode_label_objects = 1
-hole_to_polyhole = 0
-hole_to_polyhole_threshold = 0.01
-hole_to_polyhole_twisted = 1
-independent_support_layer_height = 1
+;;;hole_to_polyhole = 0
+;;;hole_to_polyhole_threshold = 0.01
+;;;hole_to_polyhole_twisted = 1
+;;;independent_support_layer_height = 1
 infill_anchor = 400%
 infill_anchor_max = 20
-infill_jerk = 20
-initial_layer_jerk = 8
-initial_layer_min_bead_width = 85%
-initial_layer_travel_speed = 100%
-inner_wall_jerk = 20
-internal_bridge_flow = 1
-internal_bridge_speed = 150%
-internal_solid_infill_acceleration = 100%
-internal_solid_infill_pattern = monotonic
-ironing_angle = -1
-ironing_pattern = zig-zag
-ironing_support_layer = 0
-is_infill_first = 0
-make_overhang_printable = 0
-make_overhang_printable_angle = 55
-make_overhang_printable_hole_size = 0
-max_bridge_length = 10
-max_volumetric_extrusion_rate_slope = 0
-max_volumetric_extrusion_rate_slope_segment_length = 3
+;;;infill_jerk = 20
+;;;initial_layer_jerk = 8
+;;;initial_layer_min_bead_width = 85%
+;;;initial_layer_travel_speed = 100%
+;;;inner_wall_jerk = 20
+;;;internal_bridge_flow = 1
+;;;internal_bridge_speed = 150%
+solid_infill_acceleration = 100%
+solid_fill_pattern = monotonic
+;;;ironing_angle = -1
+;;;ironing_pattern = zigzag
+;;;ironing_support_layer = 0
+infill_first = 0
+;;;make_overhang_printable = 0
+;;;make_overhang_printable_angle = 55
+;;;make_overhang_printable_hole_size = 0
+;;;max_bridge_length = 10
+;;;max_volumetric_extrusion_rate_slope = 0
+;;;max_volumetric_extrusion_rate_slope_segment_length = 3
 min_bead_width = 85%
 min_feature_size = 25%
-min_width_top_surface = 300%
-minimum_support_area = 5
+;;;min_width_top_surface = 300%
+;;;minimum_support_area = 5
 mmu_segmented_region_interlocking_depth = 0
 mmu_segmented_region_max_width = 0
-only_one_wall_first_layer = 0
-only_one_wall_top = 0
+;;;only_one_wall_first_layer = 0
+top_one_perimeter_type = none
 ooze_prevention = 0
-outer_wall_acceleration = 1000
-outer_wall_jerk = 20
-overhang_reverse = 0
-overhang_reverse_internal_only = 0
-overhang_reverse_threshold = 50%
-overhang_speed_classic = 0
-precise_outer_wall = 0
-prime_tower_brim_width = 3
-prime_volume = 45
-print_flow_ratio = 1
+external_perimeter_acceleration = 1000
+;;;outer_wall_jerk = 20
+;;;overhang_reverse = 0
+;;;overhang_reverse_internal_only = 0
+;;;overhang_reverse_threshold = 50%
+;;;overhang_speed_classic = 0
+;;;precise_outer_wall = 0
+wipe_tower_brim_width = 3
+;;;prime_volume = 45
+;;;print_flow_ratio = 1
 raft_contact_distance = 0.1
 raft_expansion = 1.5
 raft_first_layer_density = 90%
 raft_first_layer_expansion = 2
-role_based_wipe_speed = 1
-seam_gap = 10%
+;;;role_based_wipe_speed = 1
+seam_gap_distance = 10%
 single_extruder_multi_material_priming = 0
-skirt_speed = 50
+;;;skirt_speed = 50
 slice_closing_radius = 0.049
 slicing_mode = regular
-slow_down_layers = 0
-slowdown_for_curled_perimeters = 0
+;;;slow_down_layers = 0
+avoid_crossing_curled_overhangs = 0
 small_perimeter_speed = 50%
-small_perimeter_threshold = 0
-solid_infill_filament = 1
-sparse_infill_acceleration = 100%
-sparse_infill_filament = 1
-speed_limit_to_height = [[100,150,100,6000],[150,200,80,5500],[200,250,60,5000]]
-speed_limit_to_height_enable = 0
-spiral_mode_max_xy_smoothing = 200%
-spiral_mode_smooth = 0
+;;;small_perimeter_threshold = 0
+;;;solid_infill_filament = 1
+infill_acceleration = 100%
+;;;sparse_infill_filament = 1
+;;;speed_limit_to_height = [[100,150,100,6000],[150,200,80,5500],[200,250,60,5000]]
+;;;speed_limit_to_height_enable = 0
+;;;spiral_mode_max_xy_smoothing = 200%
+;;;spiral_mode_smooth = 0
 staggered_inner_seams = 0
 thick_bridges = 0
-thick_internal_bridges = 1
-timelapse_type = 0
-top_solid_infill_flow_ratio = 1
-top_surface_jerk = 20
-travel_jerk = 8
+;;;thick_internal_bridges = 1
+;;;timelapse_type = 0
+;;;top_solid_infill_flow_ratio = 1
+;;;top_surface_jerk = 20
+;;;travel_jerk = 8
 travel_speed_z = 0
 wall_distribution_count = 1
-wall_filament = 1
-wall_generator = arachne
-wall_sequence = inner wall/outer wall
+;;;wall_filament = 1
+perimeter_generator = arachne
+;;;wall_sequence = inner wall/outer wall
 wall_transition_angle = 10
 wall_transition_filter_deviation = 25%
 wall_transition_length = 100%
-wipe_before_external_loop = 0
-wipe_on_loops = 0
-wipe_speed = 80%
+;;;wipe_before_external_loop = 0
+;;;wipe_on_loops = 0
+;;;wipe_speed = 80%
 wipe_tower_bridging = 10
 wipe_tower_cone_angle = 0
 wipe_tower_extra_spacing = 100%
-wipe_tower_rotation_angle = 0
-wiping_volumes_extruders = 70,70,70,70,70,70,70,70,70,70
+;;;wipe_tower_rotation_angle = 0
+;;;wiping_volumes_extruders = 70,70,70,70,70,70,70,70,70,70

print_config/prusa_slicer/quality/0.20mm_Standard.ini

@@ -3,224 +3,224 @@ show_name = 0.20mm Standard Quality
 
 
 [settings]
-adaptive_layer_height = 0
-reduce_crossing_wall = 0
-bridge_flow = 0.95
+variable_layer_height = 0
+avoid_crossing_perimeters = 0
+bridge_flow_ratio = 0.95
 bridge_speed = 50
 brim_width = 5
-print_sequence = by layer
+complete_objects = 0
 default_acceleration = 2500
-bridge_no_support = 0
+dont_support_bridges = 0
 elefant_foot_compensation = 0.15
-outer_wall_line_width = 0.42
-outer_wall_speed = 60
-line_width = 0.45
-infill_direction = 45
-sparse_infill_density = 15%
-sparse_infill_pattern = zig-zag
-initial_layer_line_width = 0.5
-initial_layer_print_height = 0.2
-initial_layer_speed = 30
-gap_infill_speed = 50
-infill_combination = 0
-sparse_infill_line_width = 0.45
-infill_wall_overlap = 30
-sparse_infill_speed = 180
+external_perimeter_extrusion_width = 0.42
+external_perimeter_speed = 60
+extrusion_width = 0.45
+fill_angle = 45
+fill_density = 15%
+fill_pattern = zigzag
+first_layer_extrusion_width = 0.5
+first_layer_height = 0.2
+first_layer_speed = 30
+gap_fill_speed = 50
+solid_infill_every_layers = 0
+infill_extrusion_width = 0.45
+infill_overlap = 30%
+infill_speed = 180
 interface_shells = 0
-detect_overhang_wall = 1
-reduce_infill_retraction = 1
-wall_loops = 2
-inner_wall_line_width = 0.45
-inner_wall_speed = 90
-print_settings_id = 
+;;detect_overhang_wall = 1
+;;reduce_infill_retraction = 1
+perimeters = 2
+perimeter_extrusion_width = 0.45
+perimeter_speed = 90
+;;;print_settings_id = 
 raft_layers = 0
 seam_position = aligned
 skirt_distance = 2
 skirt_height = 2
-minimum_sparse_infill_area = 10
-internal_solid_infill_line_width = 0.42
-internal_solid_infill_speed = 180
-spiral_mode = 0
+solid_infill_below_area = 10
+solid_infill_extrusion_width = 0.42
+solid_infill_speed = 180
+spiral_vase = 0
 standby_temperature_delta = -5
-detect_thin_wall = 0
-top_surface_line_width = 0.42
-top_surface_speed = 50
+thin_walls = 0
+top_infill_extrusion_width = 0.42
+top_solid_infill_speed = 50
 travel_speed = 150
-enable_prime_tower = 0
-prime_tower_width = 60
-xy_hole_compensation = 0
-xy_contour_compensation = 0
-max_travel_detour_distance = 0
-bottom_surface_pattern = monotonic
-bottom_shell_layers = 4
-bottom_shell_thickness = 0
-brim_object_gap = 0.1
-compatible_printers_condition = 
-top_surface_acceleration = 2500
+wipe_tower = 0
+wipe_tower_width = 60
+xy_size_compensation = 0
+;;;xy_contour_compensation = 0
+;;;max_travel_detour_distance = 0
+bottom_fill_pattern = monotonic
+bottom_solid_layers = 4
+bottom_solid_min_thickness = 0
+;;;brim_object_gap = 0.1
+;;;compatible_printers_condition = 
+top_solid_infill_acceleration = 2500
 draft_shield = disabled
-enable_arc_fitting = 1
-wall_infill_order = inner wall/outer wall/infill
-initial_layer_acceleration = 500
+arc_fitting = disabled
+;;;wall_infill_order = inner wall/outer wall/infill
+first_layer_acceleration = 500
 travel_acceleration = 2500
-inner_wall_acceleration = 2000
-ironing_flow = 15%
+perimeter_acceleration = 2000
+ironing_flowrate = 15%
 ironing_spacing = 0.1
 ironing_speed = 20
 ironing_type = top
 layer_height = 0.2
-overhang_1_4_speed = 0
-overhang_2_4_speed = 60
-overhang_3_4_speed = 30
-overhang_4_4_speed = 10
-skirt_loops = 0
+overhang_speed_0 = 0
+overhang_speed_1 = 60
+overhang_speed_2 = 30
+overhang_speed_3 = 10
+skirts = 2
 resolution = 0.012
 
-top_surface_pattern = monotonic
-top_shell_layers = 4
-top_shell_thickness = 0.8
-initial_layer_infill_speed = 80
+top_fill_pattern = monotonic
+top_solid_layers = 4
+top_solid_min_thickness = 0.8
+first_layer_infill_speed = 80
 wipe_tower_no_sparse_layers = 0
-accel_to_decel_enable = 1
-accel_to_decel_factor = 25
-acceleration_limit_mess = [[0.5,1.0,100,6000],[1.0,1.5,80,5500],[1.5,2.0,60,5000]]
-acceleration_limit_mess_enable = 0
-ai_infill = 0
-alternate_extra_wall = 0
-bottom_solid_infill_flow_ratio = 1
+;;;accel_to_decel_enable = 1
+;;;accel_to_decel_factor = 25
+;;;acceleration_limit_mess = [[0.5,1.0,100,6000],[1.0,1.5,80,5500],[1.5,2.0,60,5000]]
+;;;acceleration_limit_mess_enable = 0
+;;;ai_infill = 0
+;;;alternate_extra_wall = 0
+;;;bottom_solid_infill_flow_ratio = 1
 bridge_acceleration = 50%
 bridge_angle = 0
-bridge_density = 100%
-brim_ears_detection_length = 1
-brim_ears_max_angle = 125
+;;;bridge_density = 100%
+;;;brim_ears_detection_length = 1
+;;;brim_ears_max_angle = 125
 brim_type = no_brim
-counterbore_hole_bridging = none
-default_jerk = 10
-detect_narrow_internal_solid_infill = 1
-dont_filter_internal_bridges = disabled
-elefant_foot_compensation_layers = 1
-enable_overhang_speed = 1
-enforce_support_layers = 0
+;;;counterbore_hole_bridging = none
+;;;default_jerk = 10
+;;;detect_narrow_internal_solid_infill = 1
+;;;dont_filter_internal_bridges = disabled
+;;;elefant_foot_compensation_layers = 1
+enable_dynamic_overhang_speeds = 1
+support_material_enforce_layers = 0
 ensure_vertical_shell_thickness = ensure_all
-exclude_object = 0
+;;;exclude_object = 0
 extra_perimeters_on_overhangs = 0
-filter_out_gap_fill = 0
-flush_into_infill = 0
-flush_into_objects = 0
-flush_into_support = 1
+;;;filter_out_gap_fill = 0
+;;;flush_into_infill = 0
+;;;flush_into_objects = 0
+;;;flush_into_support = 1
 fuzzy_skin = none
-fuzzy_skin_first_layer = 0
-fuzzy_skin_point_distance = 0.8
+;;;fuzzy_skin_first_layer = 0
+fuzzy_skin_point_dist = 0.8
 fuzzy_skin_thickness = 0.3
-gap_fill_target = everywhere
-gcode_add_line_number = 0
+gap_fill_enabled = everywhere
+;;;gcode_add_line_number = 0
 gcode_comments = 0
 gcode_label_objects = 1
-hole_to_polyhole = 0
-hole_to_polyhole_threshold = 0.01
-hole_to_polyhole_twisted = 1
-independent_support_layer_height = 1
+;;;hole_to_polyhole = 0
+;;;hole_to_polyhole_threshold = 0.01
+;;;hole_to_polyhole_twisted = 1
+;;;independent_support_layer_height = 1
 infill_anchor = 400%
 infill_anchor_max = 20
-infill_jerk = 10
-initial_layer_jerk = 10
-initial_layer_min_bead_width = 85%
-initial_layer_travel_speed = 100%
-inner_wall_jerk = 10
-internal_bridge_flow = 1
-internal_bridge_speed = 150%
-internal_solid_infill_acceleration = 100%
-internal_solid_infill_pattern = monotonic
-ironing_angle = -1
-ironing_pattern = zig-zag
-ironing_support_layer = 0
-is_infill_first = 0
-make_overhang_printable = 0
-make_overhang_printable_angle = 55
-make_overhang_printable_hole_size = 0
-material_flow_dependent_temperature = 0
-material_flow_temp_graph = [[3.0,210],[10.0,220],[12.0,230]]
-max_bridge_length = 10
-max_volumetric_extrusion_rate_slope = 0
-max_volumetric_extrusion_rate_slope_segment_length = 3
+;;;infill_jerk = 10
+;;;initial_layer_jerk = 10
+;;;initial_layer_min_bead_width = 85%
+;;;initial_layer_travel_speed = 100%
+;;;inner_wall_jerk = 10
+;;;internal_bridge_flow = 1
+;;;internal_bridge_speed = 150%
+solid_infill_acceleration = 100%
+solid_fill_pattern = monotonic
+;;;ironing_angle = -1
+;;;ironing_pattern = zigzag
+;;;ironing_support_layer = 0
+infill_first = 0
+;;;make_overhang_printable = 0
+;;;make_overhang_printable_angle = 55
+;;;make_overhang_printable_hole_size = 0
+;;;material_flow_dependent_temperature = 0
+;;;material_flow_temp_graph = [[3.0,210],[10.0,220],[12.0,230]]
+;;;max_bridge_length = 10
+;;;max_volumetric_extrusion_rate_slope = 0
+;;;max_volumetric_extrusion_rate_slope_segment_length = 3
 min_bead_width = 85%
 min_feature_size = 25%
-min_length_factor = 0.5
-min_width_top_surface = 300%
-minimum_support_area = 5
+;;;min_length_factor = 0.5
+;;;min_width_top_surface = 300%
+;;;minimum_support_area = 5
 mmu_segmented_region_interlocking_depth = 0
 mmu_segmented_region_max_width = 0
-only_one_wall_first_layer = 0
-only_one_wall_top = 1
+;;;only_one_wall_first_layer = 0
+top_one_perimeter_type = top
 ooze_prevention = 0
-outer_wall_acceleration = 1000
-outer_wall_jerk = 10
-overhang_reverse = 0
-overhang_reverse_internal_only = 0
-overhang_reverse_threshold = 50%
-overhang_speed_classic = 0
-precise_outer_wall = 0
-prime_tower_brim_width = 3
-prime_tower_enhance_type = chamfer
-prime_volume = 45
-print_flow_ratio = 1
-print_order = default
+external_perimeter_acceleration = 1000
+;;;outer_wall_jerk = 10
+;;;overhang_reverse = 0
+;;;overhang_reverse_internal_only = 0
+;;;overhang_reverse_threshold = 50%
+;;;overhang_speed_classic = 0
+;;;precise_outer_wall = 0
+wipe_tower_brim_width = 3
+;;;prime_tower_enhance_type = chamfer
+;;;prime_volume = 45
+;;;print_flow_ratio = 1
+;;;print_order = default
 raft_contact_distance = 0.1
 raft_expansion = 1.5
 raft_first_layer_density = 90%
 raft_first_layer_expansion = 2
-role_based_wipe_speed = 0
-scarf_angle_threshold = 155
-scarf_joint_flow_ratio = 1
-scarf_joint_speed = 100%
-scarf_overhang_threshold = 40%
-seam_gap = 10%
-seam_slope_conditional = 0
-seam_slope_entire_loop = 0
-seam_slope_inner_walls = 0
-seam_slope_min_length = 20
-seam_slope_start_height = 0
-seam_slope_steps = 10
-seam_slope_type = none
+;;;role_based_wipe_speed = 0
+;;;scarf_angle_threshold = 155
+;;;scarf_joint_flow_ratio = 1
+;;;scarf_joint_speed = 100%
+;;;scarf_overhang_threshold = 40%
+seam_gap_distance = 10%
+;;;seam_slope_conditional = 0
+scarf_seam_entire_loop = 0
+scarf_seam_on_inner_perimeters = 0
+scarf_seam_length = 20
+scarf_seam_start_height = 0
+;;;seam_slope_steps = 10
+;;;seam_slope_type = none
 single_extruder_multi_material_priming = 0
-skirt_speed = 50
+;;;skirt_speed = 50
 slice_closing_radius = 0.049
 slicing_mode = regular
-slow_down_layers = 0
-slowdown_for_curled_perimeters = 0
-small_area_infill_flow_compensation = 0
-small_area_infill_flow_compensation_model = 0,0;"\n0.2,0.4444";"\n0.4,0.6145";"\n0.6,0.7059";"\n0.8,0.7619";"\n1.5,0.8571";"\n2,0.8889";"\n3,0.9231";"\n5,0.9520";"\n10,1"
+;;;slow_down_layers = 0
+avoid_crossing_curled_overhangs = 0
+;;;small_area_infill_flow_compensation = 0
+;;;small_area_infill_flow_compensation_model = 0,0;"\n0.2,0.4444";"\n0.4,0.6145";"\n0.6,0.7059";"\n0.8,0.7619";"\n1.5,0.8571";"\n2,0.8889";"\n3,0.9231";"\n5,0.9520";"\n10,1"
 small_perimeter_speed = 50%
-small_perimeter_threshold = 0
-solid_infill_filament = 1
-sparse_infill_acceleration = 100%
-sparse_infill_filament = 1
-speed_limit_to_height = [[100,150,100,6000],[150,200,80,5500],[200,250,60,5000]]
-speed_limit_to_height_enable = 0
-spiral_mode_max_xy_smoothing = 200%
-spiral_mode_smooth = 0
+;;;small_perimeter_threshold = 0
+;;;solid_infill_filament = 1
+infill_acceleration = 100%
+;;;sparse_infill_filament = 1
+;;;speed_limit_to_height = [[100,150,100,6000],[150,200,80,5500],[200,250,60,5000]]
+;;;speed_limit_to_height_enable = 0
+;;;spiral_mode_max_xy_smoothing = 200%
+;;;spiral_mode_smooth = 0
 staggered_inner_seams = 1
 
 thick_bridges = 0
-thick_internal_bridges = 1
-timelapse_type = 0
-top_solid_infill_flow_ratio = 1
-top_surface_jerk = 8
-travel_jerk = 10
+;;;thick_internal_bridges = 1
+;;;timelapse_type = 0
+;;;top_solid_infill_flow_ratio = 1
+;;;top_surface_jerk = 8
+;;;travel_jerk = 10
 travel_speed_z = 0
 
-wall_direction = auto
+;;;wall_direction = auto
 wall_distribution_count = 1
-wall_filament = 1
-wall_generator = arachne
-wall_sequence = inner wall/outer wall
+;;;wall_filament = 1
+perimeter_generator = arachne
+;;;wall_sequence = inner wall/outer wall
 wall_transition_angle = 10
 wall_transition_filter_deviation = 25%
 wall_transition_length = 100%
-wipe_before_external_loop = 0
-wipe_on_loops = 0
-wipe_speed = 100%
+;;;wipe_before_external_loop = 0
+;;;wipe_on_loops = 0
+;;;wipe_speed = 100%
 wipe_tower_bridging = 10
 wipe_tower_cone_angle = 0
 wipe_tower_extra_spacing = 100%
-wipe_tower_rotation_angle = 0
-wiping_volumes_extruders = 70,70,70,70,70,70,70,70,70,70
+;;;wipe_tower_rotation_angle = 0
+;;;wiping_volumes_extruders = 70,70,70,70,70,70,70,70,70,70

print_config/prusa_slicer/supports/grid_support.ini

@@ -1,5 +1,5 @@
 [metadata]
-show_name = Grid Support
+show_name = 网状支撑 (Grid Support)
 
 
 [settings]
@@ -7,11 +7,11 @@ support_material = 1
 support_material_auto = 1
 support_material_extrusion_width = 0.4
 support_material_interface_extruder = 0
-support_top_z_distance = 0.2
-support_interface_loop_pattern = 0
-support_interface_top_layers = 2
-support_interface_spacing = 0.5
-support_interface_speed = 100%
+support_material_contact_distance = 0.2
+;;;support_interface_loop_pattern = 0
+support_material_interface_layers = 2
+support_material_interface_spacing = 0.5
+support_material_interface_speed = 100%
 support_material_pattern = rectilinear
 support_material_spacing = 2.5
 support_material_speed = 50
@@ -24,11 +24,11 @@ support_material_bottom_interface_layers = 2
 
 
 support_material_angle = 0
-support_bottom_interface_spacing = 0.5
-support_bottom_z_distance = 0.2
-support_critical_regions_only = 0
-support_expansion = 0
-support_interface_not_for_body = 1
-support_interface_pattern = auto
-support_remove_small_overhang = 1
-support_xy_overrides_z = xy_overrides_z
+;;;support_bottom_interface_spacing = 0.5
+support_material_bottom_contact_distance = 0.2
+;;;support_critical_regions_only = 0
+;;;support_expansion = 0
+;;;support_interface_not_for_body = 1
+support_material_interface_pattern = auto
+;;;support_remove_small_overhang = 1
+;;;support_xy_overrides_z = xy_overrides_z

print_config/prusa_slicer/supports/no_support.ini

@@ -1,50 +1,50 @@
 [metadata]
-show_name = No Support
+show_name = 无支撑 (No Support)
 
 
 [settings]
 support_material = 0
 
-support_line_width = 0.4
-support_interface_filament = 0
-support_on_build_plate_only = 0
-support_top_z_distance = 0.2
-support_interface_loop_pattern = 0
-support_interface_top_layers = 2
-support_interface_spacing = 0.5
-support_interface_speed = 100%
-support_base_pattern = rectilinear
-support_base_pattern_spacing = 2.5
-support_speed = 50
-support_threshold_angle = 30
-support_object_xy_distance = 0.35
+;;;support_line_width = 0.4
+;;;support_interface_filament = 0
+;;;support_on_build_plate_only = 0
+support_material_contact_distance = 0.2
+;;;support_interface_loop_pattern = 0
+support_material_interface_layers = 2
+support_material_interface_spacing = 0.5
+support_material_interface_speed = 100%
+;;;support_base_pattern = rectilinear
+;;;support_base_pattern_spacing = 2.5
+support_material_speed = 50
+;;;support_threshold_angle = 30
+;;;support_object_xy_distance = 0.35
 
-support_type = normal(auto)
+;;;support_type = 1
 support_material_style = default
-support_interface_bottom_layers = 2
-tree_support_branch_angle = 45
-tree_support_wall_count = 0
+support_material_bottom_interface_layers = 2
+;;;tree_support_branch_angle = 45
+;;;tree_support_wall_count = 0
 
-support_angle = 0
-support_bottom_interface_spacing = 0.5
-support_bottom_z_distance = 0.2
-support_critical_regions_only = 0
-support_expansion = 0
-support_interface_not_for_body = 1
-support_interface_pattern = auto
-support_remove_small_overhang = 1
-support_xy_overrides_z = xy_overrides_z
+support_material_angle = 0
+;;;support_bottom_interface_spacing = 0.5
+support_material_bottom_contact_distance = 0.2
+;;;support_critical_regions_only = 0
+;;;support_expansion = 0
+;;;support_interface_not_for_body = 1
+support_material_interface_pattern = auto
+;;;support_remove_small_overhang = 1
+;;;support_xy_overrides_z = xy_overrides_z
 
-tree_support_adaptive_layer_height = 1
-tree_support_angle_slow = 25
-tree_support_auto_brim = 1
-tree_support_branch_angle_organic = 40
-tree_support_branch_diameter = 2
-tree_support_branch_diameter_angle = 5
-tree_support_branch_diameter_double_wall = 3
-tree_support_branch_diameter_organic = 2
-tree_support_branch_distance = 5
-tree_support_branch_distance_organic = 1
-tree_support_brim_width = 3
-tree_support_tip_diameter = 0.8
-tree_support_top_rate = 30%
+;;;tree_support_adaptive_layer_height = 1
+;;;tree_support_angle_slow = 25
+;;;tree_support_auto_brim = 1
+;;;tree_support_branch_angle_organic = 40
+;;;tree_support_branch_diameter = 2
+;;;tree_support_branch_diameter_angle = 5
+;;;tree_support_branch_diameter_double_wall = 3
+;;;tree_support_branch_diameter_organic = 2
+;;;tree_support_branch_distance = 5
+;;;tree_support_branch_distance_organic = 1
+;;;tree_support_brim_width = 3
+;;;tree_support_tip_diameter = 0.8
+;;;tree_support_top_rate = 30%

print_config/prusa_slicer/supports/snug_support.ini

@@ -1,5 +1,5 @@
 [metadata]
-show_name = Snug Support
+show_name = 松散支撑 (Snug Support)
 
 
 [settings]
@@ -7,11 +7,11 @@ support_material = 1
 support_material_auto = 1
 support_material_extrusion_width = 0.4
 support_material_interface_extruder = 0
-support_top_z_distance = 0.2
-support_interface_loop_pattern = 0
-support_interface_top_layers = 2
-support_interface_spacing = 0.5
-support_interface_speed = 100%
+support_material_contact_distance = 0.2
+;;;support_interface_loop_pattern = 0
+support_material_interface_layers = 2
+support_material_interface_spacing = 0.5
+support_material_interface_speed = 100%
 support_material_pattern = rectilinear
 support_material_spacing = 2.5
 support_material_speed = 50
@@ -24,11 +24,11 @@ support_material_bottom_interface_layers = 2
 
 
 support_material_angle = 0
-support_bottom_interface_spacing = 0.5
-support_bottom_z_distance = 0.2
-support_critical_regions_only = 0
-support_expansion = 0
-support_interface_not_for_body = 1
-support_interface_pattern = auto
-support_remove_small_overhang = 1
-support_xy_overrides_z = xy_overrides_z
+;;;support_bottom_interface_spacing = 0.5
+support_material_bottom_contact_distance = 0.2
+;;;support_critical_regions_only = 0
+;;;support_expansion = 0
+;;;support_interface_not_for_body = 1
+support_material_interface_pattern = auto
+;;;support_remove_small_overhang = 1
+;;;support_xy_overrides_z = xy_overrides_z

print_config/prusa_slicer/supports/tree_support.ini

@@ -1,5 +1,5 @@
 [metadata]
-show_name = Tree Support
+show_name = 树状支撑 (Tree Support)
 
 
 [settings]
@@ -7,11 +7,11 @@ support_material = 1
 support_material_auto = 1
 support_material_extrusion_width = 0.4
 support_material_interface_extruder = 0
-support_top_z_distance = 0.2
-support_interface_loop_pattern = 0
-support_interface_top_layers = 2
-support_interface_spacing = 0.5
-support_interface_speed = 100%
+support_material_contact_distance = 0.2
+;;;support_interface_loop_pattern = 0
+support_material_interface_layers = 2
+support_material_interface_spacing = 0.5
+support_material_interface_speed = 100%
 support_material_pattern = rectilinear
 support_material_spacing = 2.5
 support_material_speed = 50
@@ -24,14 +24,14 @@ support_material_bottom_interface_layers = 2
 
 
 support_material_angle = 0
-support_bottom_interface_spacing = 0.5
-support_bottom_z_distance = 0.2
-support_critical_regions_only = 0
-support_expansion = 0
-support_interface_not_for_body = 1
-support_interface_pattern = auto
-support_remove_small_overhang = 1
-support_xy_overrides_z = xy_overrides_z
+;;;support_bottom_interface_spacing = 0.5
+support_material_bottom_contact_distance = 0.2
+;;;support_critical_regions_only = 0
+;;;support_expansion = 0
+;;;support_interface_not_for_body = 1
+support_material_interface_pattern = auto
+;;;support_remove_small_overhang = 1
+;;;support_xy_overrides_z = xy_overrides_z
 
 
 support_tree_angle = 45
@@ -48,4 +48,4 @@ support_tree_branch_distance = 5
 ; tree_support_branch_distance_organic = 1
 ; tree_support_brim_width = 3
 support_tree_tip_diameter = 0.8
-support_tree_top_rate = 30%
+support_tree_top_rate = 30%