[metadata]
show_name = Hyper PETG
material_type = petg


[settings]
filament_adhesiveness_category = 300
cool_plate_temp = 60
eng_plate_temp = 0
hot_plate_temp = 70
textured_plate_temp = 70
cool_plate_temp_initial_layer = 60
eng_plate_temp_initial_layer = 0
hot_plate_temp_initial_layer = 70
textured_plate_temp_initial_layer = 70
overhang_fan_threshold = 25%
overhang_fan_speed = 90
slow_down_for_layer_cooling = 1
close_fan_the_first_x_layers = 3
filament_end_gcode = ;filament end gcode \n
filament_flow_ratio = 1.0
reduce_fan_stop_start_freq = 1
fan_cooling_layer_time = 30
filament_cost = 69
filament_density = 1.27
filament_deretraction_speed = nil
filament_diameter = 1.75
filament_max_volumetric_speed = 10
filament_minimal_purge_on_wipe_tower = 15
filament_retraction_minimum_travel = nil
filament_retract_before_wipe = nil
filament_retract_when_changing_layer = nil
filament_retraction_length = 1.2
filament_z_hop = 0.2
filament_z_hop_types = nil
filament_retract_restart_extra = 0
filament_retraction_speed = nil
filament_settings_id = 
filament_soluble = 0
filament_type = PETG
filament_vendor = Creality
filament_wipe = nil
filament_wipe_distance = 2
bed_type = Cool Plate
nozzle_temperature_initial_layer = 235
full_fan_speed_layer = 0
fan_max_speed = 80
fan_min_speed = 40
slow_down_min_speed = 10
slow_down_layer_time = 8
filament_start_gcode = ;filament start gcode\n
nozzle_temperature = 240
temperature_vitrification = 80
activate_air_filtration = 0
activate_chamber_temp_control = 0
additional_cooling_fan_speed = 0
chamber_temperature = 0
complete_print_exhaust_fan_speed = 80
cool_cds_fan_start_at_height = 0
cool_special_cds_fan_speed = 0
default_filament_colour = ""
during_print_exhaust_fan_speed = 60
enable_overhang_bridge_fan = 1
enable_pressure_advance = 1
enable_special_area_additional_cooling_fan = 0
epoxy_resin_plate_temp = 0
epoxy_resin_plate_temp_initial_layer = 0
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_is_support = 0
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_multitool_ramming = 0
filament_multitool_ramming_flow = 10
filament_multitool_ramming_volume = 10
filament_notes = ""
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_lift_above = 0
filament_retract_lift_below = 0
filament_retract_lift_enforce = All Surfaces
filament_shrink = 100%
filament_toolchange_delay = 0
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
material_flow_dependent_temperature = 1
material_flow_temp_graph = [[3.0,230],[10.0,240],[20.0,250]]
nozzle_temperature_range_high = 270
nozzle_temperature_range_low = 220
pressure_advance = 0.07
required_nozzle_HRC = 0
support_material_interface_fan_speed = -1
